iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4154-22

(Specification)

Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt Fabrics

Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.  
5.2 It is recognized that for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: This fabric meets ASTM Specification D4154 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers knitted and woven fabrics comprised of any textile fiber or mixture of fibers used in men's and boy's beachwear and sports shirts.  
1.2 This performance specification is not applicable to knitted and woven fabrics used for interlining and swimwear.  
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Oct-2022
ICS
61.020 - Clothes
Technical Committee
D13 - Textiles
Drafting Committee
D13.61 - Apparel
Current Stage
Ref Project

Relations

Refers
ASTM D3787-16(2020) - Standard Test Method for Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test
Effective Date
01-Jul-2020

Buy Standard

ASTM D4154-22 - Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt FabricsASTM D4154-22 - Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt Fabrics
PreviousNext
Technical specification
ASTM D4154-22 - Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt Fabrics
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D4154-22 - Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt FabricsREDLINE ASTM D4154-22 - Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt Fabrics
PreviousNext
Technical specification
REDLINE ASTM D4154-22 - Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt Fabrics
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D4154 −22
Standard Performance Specification for
Men’s and Boys’ Knitted and Woven Beachwear and Sports
1
Shirt Fabrics
This standard is issued under the fixed designation D4154; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope by the Tongue (Single Rip) Method (Constant-Rate-of-
3
Traverse Tensile Testing Machine) (Withdrawn 1995)
1.1 This performance specification covers knitted and wo-
D2594 TestMethodforStretchPropertiesofKnittedFabrics
ven fabrics comprised of any textile fiber or mixture of fibers
Having Low Power
used in men’s and boy’s beachwear and sports shirts.
D2724 Test Method for Bond Strength of Bonded, Fused,
1.2 This performance specification is not applicable to
and Laminated Apparel Fabrics
knitted and woven fabrics used for interlining and swimwear.
D3786 Test Method for Bursting Strength of Textile
1.3 These requirements apply to both the length and width
Fabrics—Diaphragm Bursting Strength Tester Method
directions for those properties where fabric direction is perti-
D3787 Test Method for Bursting Strength of Textiles—
nent.
Constant-Rate-of-Traverse (CRT) Ball Burst Test
1.4 This standard does not purport to address all of the
D5034 TestMethodforBreakingStrengthandElongationof
safety concerns, if any, associated with its use. It is the
Textile Fabrics (Grab Test)
responsibility of the user of this standard to establish appro- 3
D7022 Terminology Relating toApparel (Withdrawn 2022)
priate safety, health, and environmental practices and deter-
4
2.2 AATCC Test Methods:
mine the applicability of regulatory limitations prior to use.
TM8 Colorfastness to Crocking: Crockmeter Method
1.5 This international standard was developed in accor-
TM15 Colorfastness to Perspiration
dance with internationally recognized principles on standard-
TM16.3 Colorfastness to Light: Xenon-Arc
ization established in the Decision on Principles for the
TM23 Colorfastness to Burnt Gas Fumes
Development of International Standards, Guides and Recom-
TM61 Colorfastness to Laundering: Accelerated
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee. TM96 Dimensional Changes in Laundering of Woven and
Knitted Textiles Except Wool
2. Referenced Documents
TM116 Colorfastness to Crocking: Rotary Vertical Crock-
2
meter Method
2.1 ASTM Standards:
D123 Terminology Relating to Textiles TM124 Smoothness Appearance of Fabrics After Repeated
D434 Test Method for Resistance to Slippage of Yarns in Home Launderings
Woven Fabrics Using a Standard Seam (Withdrawn
TM132 Colorfastness to Drycleaning
3
2003)
TM135 Dimensional Changes of Fabrics after Home Laun-
D1424 Test Method for Tearing Strength of Fabrics by
dering
Falling-Pendulum (Elmendorf-Type) Apparatus
TM172 Colorfastness to Powdered Non-chlorine Bleach in
D2262 Test Method for Tearing Strength of Woven Fabrics
Home Laundering
TM188 Colorfastness to Sodium Hypochlorite Bleach in
Home Laundering
1
This performance specification is under the jurisdiction of ASTM Committee
EP1 Gray Scale for Color Change
D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on
Apparel. EP2 Gray Scale for Staining
Current edition approved Nov. 1, 2022. Published November 2022. Originally
EP8 AATCC 9-Step Chromatic Transference Scale
approved in 1982. Last previous edition approved in 2014 as D4154 – 14. DOI:
M11 A Glossary of AATCC Standard Terminology
10.1520/D4154-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
4
the ASTM website. AATCC Technical Manual, available from American Association of Textile
3
The last approved version of this historical standard is referenced on Chemists and Colorists (AATCC), P.O. Box 12215, Research Triangle Park, NC
www.astm.org. 27709, http://www.aatcc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4154−22
5
2.3 Federal Standard: 3.3 For terms relating to chemical or colorfastness testing,
16 CFR,ChapterII—ConsumerProductSafetyCommission refer to specific AATCC test methods, or the Glossary of
Subchapter D—Flammable Fabrics Act Regulations. AATCC Standard Terminology, or both.
6
2.4 Military Standard:
3.4 Definitions
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D4154 − 14 D4154 − 22
Standard Performance Specification for
Men’s and Boys’ Knitted and Woven Beachwear and Sports
1
Shirt Fabrics
This standard is issued under the fixed designation D4154; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This performance specification covers knitted and woven fabrics comprised of any textile fiber or mixture of fibers used in
men’s and boy’s beachwear and sports shirts.
1.2 This performance specification is not applicable to knitted and woven fabrics used for interlining and swimwear.
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D123 Terminology Relating to Textiles
3
D434 Test Method for Resistance to Slippage of Yarns in Woven Fabrics Using a Standard Seam (Withdrawn 2003)
D1424 Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus
D2262 Test Method for Tearing Strength of Woven Fabrics by the Tongue (Single Rip) Method (Constant-Rate-of-Traverse
3
Tensile Testing Machine) (Withdrawn 1995)
D2594 Test Method for Stretch Properties of Knitted Fabrics Having Low Power
D2724 Test Method for Bond Strength of Bonded, Fused, and Laminated Apparel Fabrics
3
D2905 Practice for Statements on Number of Specimens for Textiles (Withdrawn 2008)
D3786 Test Method for Bursting Strength of Textile Fabrics—Diaphragm Bursting Strength Tester Method
D3787 Test Method for Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test
D5034 Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
3
D7022 Terminology Relating to Apparel (Withdrawn 2022)
1
This performance specification is under the jurisdiction of ASTM Committee D13 on Textiles and is the direct responsibility of Subcommittee D13.61 on Apparel.
Current edition approved Feb. 1, 2014Nov. 1, 2022. Published March 2014November 2022. Originally approved in 1982. Last previous edition approved in 20082014 as
D4154 – 01D4154 – 14.(2008). DOI: 10.1520/D4154-14.10.1520/D4154-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4154 − 22
4
2.2 AATCC Test Methods:
8TM8 Colorfastness to Crocking: Crockmeter Method
15TM15 Colorfastness to Perspiration
16.3TM16.3 Colorfastness to Light: Xenon-Arc
23TM23 Colorfastness to Burnt Gas Fumes
61TM61 Colorfastness to Laundering: Accelerated
96TM96 Dimensional Changes in Laundering of Woven and Knitted Textiles Except Wool
116TM116 Colorfastness to Crocking: Rotary Vertical Crockmeter Method
124TM124 Smoothness Appearance of Fabrics After Repeated Home Launderings
132TM132 Colorfastness to Drycleaning
135TM135 Dimensional Changes of Fabrics after Home Laundering
172TM172 Colorfastness to Powdered Non-chlorine Bleach in Home Laundering
188TM188 Colorfastness to Sodium Hypochlorite Bleach in Home Laundering
Evaluation Procedure 1EP1 Gray Scale for Color Change
Evaluation Procedure 2EP2 Gray Scale for Staining
Evaluation Procedure 8EP8 AATCC 9-Step Chromatic Transference Scale
M11 A Glossary of AATCC Standard Terminology
5
2.3 Federal Standard:
16 CFR, Chapter II—Consumer Product Safety Commission Subchapter D—Flammable Fab
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7268-23(Specification)
Standard Performance Specification for Seamless Knit Garments Including Intimates and Swimwear

ABSTRACT
This specification covers the evaluation of specific performance characteristics of importance in seamless knit garments, including camisoles, panties, slips, girdles and swimwear. Different tests shall be conducted in order to determine the following properties of seamless knit garments: bursting strength, colorfastness to laundering, colorfastness to drycleaning, colorfastness to crocking, colorfastness to light, colorfastness to perspiration, colorfastness to intimates, colorfastness to sea water, colorfastness to chlorinated pool water, colorfastness to chlorine and non-chlorine bleach, dimensional change, stretch, flammability, garnet twist, and fiber content.
SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the supplier, seamless knit garments intended for this end use should meet all of the requirements listed in Table 1 of this specification. (A) See Note 4.  
4.2 It is recognized that, for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements listed in Table 1. Therefore, one or more of the requirements in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
4.2.1 In such cases, any references to the specifications should specify that: “This product meets ASTM specifications XXXX except for the following characteristic(s).”  
4.3 Where no pre-purchase agreement has been reached between the purchaser and supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for a particular product.  
4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in seamless knit garments, including camisoles, panties, slips, girdles and swimwear.  
1.2 The following safety hazards caveat pertains only to the test methods described in this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4232-23(Specification)
Standard Performance Specification for Woven Career Apparel Fabrics: Dress and Vocational

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.  
5.2 It is recognized that where more critical requirements call for higher performance levels, for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. One or more of the requirements may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4232 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers the performance requirements for woven fabrics for career apparel: dress and vocational.  
1.2 This performance specification is not applicable to career apparel fabrics that do not patently fit the category of Career Dress Apparel. Performance specifications for such fabrics should be as agreed to between the purchaser and the seller. This performance specification is not applicable to overcoat or topcoat uniform fabrics.  
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4118-23(Specification)
Standard Performance Specification for Woven Coverall, Dungaree, Overall, and Shop-Coat Fabrics

SIGNIFICANCE AND USE
5.1 Upon agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4118 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.
SCOPE
1.1 This performance specification covers woven fabrics, composed of any textile fiber or mixture of textile fibers, to be used in the manufacture of coveralls, dungarees, overalls and shop coats.  
1.2 This performance specification recognizes two levels of wearing severity relative to performance requirements for these fabrics.  
1.3 This performance specification is not applicable to woven fabrics intended for use in the manufacture of industrial-protective clothing.  
1.4 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3995-23(Specification)
Standard Performance Specification for Knitted Career Apparel Fabrics: Dress and Vocational

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3995 except for the following characteristic(s).”  
5.3 Where no pre-purchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers the minimum performance requirements for knitted fabrics for dress and vocational career apparel composed of any textile fiber or mixtures of textile fibers.  
1.2 This performance specification is not applicable to career apparel fabrics such as those used in protective clothing, that do not patently fit the categories Career Apparel or Career Apparel, Dress (see Terminology D7022 for these terms). Minimum performance specifications for such fabrics should be as agreed between the purchaser and the seller.  
1.3 These requirements apply to the length and width directions for those factors where each fabric direction is pertinent.  
1.4 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3996-23(Specification)
Standard Performance Specification for Knit Swimwear Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3996 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers circular and warp knitted fabrics for use in knit swimwear, composed of any textile fiber or mixture of textile fibers.  
1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3655-22(Specification)
Standard Performance Specification for Men's and Women's Sliver Knitted Overcoat and Jacket Fabrics

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the seller, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. (A) More than one method can be used to measure these properties. These methods cannot be used interchangeably since there can be no overall correlation between them (see Note 2, Note 3, and Note 7).(B) AATCC Gray Scale for Color Change.(C) AATCC Gray Scale for Staining.(D) AATCC 9-Step Chromatic Transference Scale.(E) It has been reported that the results for staining, obtained by standard AATCC Test Methods, on fabrics dyed to dark shades that contain a combination of polyester and spandex, or their blends, may not show the full staining propensity of such fabrics in consumer use. It is, therefore, recommended that the staining results obtained by these tests not be used for acceptance testing of such fabrics.  
4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
4.2.1 In such cases, any references to the specification shall specify that: This fabric meets ASTM Specification D3655 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers men's and women's sliver knitted overcoat and jacket fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 This performance specification is not applicable to knitted fabrics used for interlinings.  
1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3562-22(Specification)
Standard Performance Specification for Woven Drycleanable Coat Fabrics

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the seller, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. (A) See Note 6.  
4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1; therefore, one or more of the requirements may be modified by mutual agreement between the purchaser and the seller.  
4.2.1 In such cases, any references to the specification shall specify that: This fabric meets Performance Specification D3562 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
4.4 The significance and uses of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven drycleanable topcoats, overcoats, and dress coat outer fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 This performance specification is not applicable to woven fabrics used for linings, interlinings, rainwear garments, and all-purpose, water-repellent garments nor is this performance specification applicable to bonded or laminated fabrics.  
1.3 These requirements apply to both the length and width directions for those properties where each fabric direction is pertinent.  
1.4 When a fabric requires special treatment, specific methods will be described as they are developed for that material, and such special tests will have precedence over these general requirements.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this performance specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3994-22(Specification)
Standard Performance Specification for Woven Swimwear Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3994, except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics for use in men's, women's and children's swimwear, composed of any textile fiber or mixture of textile fibers.  
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.3 The following safety hazards caveat pertains only to the test method described in this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7020-22(Specification)
Standard Performance Specification for Woven Blouse, Dress, Dress Shirt & Sport Shirt Fabrics

ABSTRACT
This performance specification covers fabrics for woven blouses, dresses, dress shirts, and sport shirts. It is not however applicable to woven fabrics used for interlinings. These requirements apply to the length and width directions for those properties where fabric direction is pertinent. The fabrics shall meet the following performance requirements: breaking strength which shall be determined using a constant rate of extension tensile testing machine; resistance to yarn slippage; tearing strength; dimensional change during pressing and finishing, after laundering, or after dry cleaning; colorfastness to laundering and dry cleaning; shade change due to sodium hypochlorite bleaching or non-chlorine bleaching, burnt gas fumes, dry and wet crocking, perspiration, and xenon-arc light; fabric smoothness after pressing, laundering, and dry cleaning; and flammability.
SIGNIFICANCE AND USE
4.1 Fabrics intended for this end-use should meet all of the requirements listed in Table 1.  (A) There is more than one method that can be used to measure breaking strength, tearing strength and colorfastness. These methods cannot be used interchangeably since there may be no overall correlation between them (see Note 2 and Note 3).(B) See Note 5.  
4.2 It should be recognized that fabrics can be produced utilizing an almost infinite number of combinations of construction variables (e.g., type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1.  
4.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use.  
4.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers fabrics for woven blouses, dresses, dress shirts, and sport shirts.  
1.2 This performance specification is not applicable to woven fabrics used for interlinings.  
1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 When a fabric requires special treatment, specific methods will be described as they are developed for that material, and such special tests will have precedence over these general requirements.  
1.5 The following precautionary caveat pertains only to the test methods described in this performance specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4119-22(Specification)
Standard Performance Specification for Men's and Boys' Knitted Dress Shirt Fabrics

SIGNIFICANCE AND USE
5.1 Upon agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4119 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.
SCOPE
1.1 This performance specification covers knitted fabrics comprised of any textile fiber or mixture of fibers, used in men's and boy's dress shirts.  
1.2 This performance specification is not applicable to knitted fabrics used for interlinings.  
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off