ASTM C67-08

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
American Association State Highway and Transportation
Designation:C67–07a Designation: C 67 – 08 Officials Standard
AASHTO No.: T 32-70
Standard Test Methods for
1
Sampling and Testing Brick and Structural Clay Tile
ThisstandardisissuedunderthefixeddesignationC67;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile.Although not necessarily
applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of
freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void
area. (Additional methods of test pertinent to ceramic glazed facing tile are included in Specification C126.)
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
NOTE 1—The testing laboratory performing this test method should be evaluated in accordance with Practice C1093.
1.3Unless otherwise indicated, the values stated in inch-pound units are to be regarded as the standard. The values given in
parentheses are for information only.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C43 Terminology of Structural Clay Products
C126 Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
C150 Specification for Portland Cement
C1093 Practice for Accreditation of Testing Agencies for Masonry
E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Testing
3. Terminology
3.1 Definitions—Terminology E6 and Terminology C43 shall be considered as applying to the terms used in these test
methods.
4. Sampling
4.1 SelectionandPreparationofTestSpecimens—Forthepurposeofthesetests,full-sizebrick,tile,orsolidmasonryunitsshall
be selected by the purchaser or by the purchaser’s authorized representative. Specimens shall be representative of the lot of units
from which they are selected and shall include specimens representative of the complete range of colors, textures, and sizes and
shall be free of or brushed to remove dirt, mud, mortar, or other foreign materials unassociated with the manufacturing process.
—Forthepurposeofthesetests,full-sizebrick,tile,orsolidmasonryunitsshallbeselectedbythepurchaserorbythepurchaser’s
authorized representative. Specimens shall be representative of the lot of units from which they are selected and shall include
specimensrepresentativeofthecompleterangeofcolors,textures,andsizes.Specimensshallbefreeoforbrushedtoremovedirt,
mud,mortar,orotherforeignmaterialsunassociatedwiththemanufacturingprocess.Brushesusedtoremoveforeignmaterialshall
1
These test methods are under the jurisdiction of Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.02 on Brick and
Structural Clay Tile.
Current edition approved Dec.Nov. 1, 2007.2008. Published December 2007.November 2008. Originally approved in 1937. Last previous edition approved in 2007 as
C67–07a.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C67–08
have bristles of plastic (polymer) or horsehair. Wire brushes sh
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
American Association State Highway and Transportation
Designation:C67–07a Designation: C 67 – 08 Officials Standard
AASHTO No.: T 32-70
Standard Test Methods for
1
Sampling and Testing Brick and Structural Clay Tile
ThisstandardisissuedunderthefixeddesignationC67;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile.Although not necessarily
applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of
freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void
area. (Additional methods of test pertinent to ceramic glazed facing tile are included in Specification C126.)
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
NOTE 1—The testing laboratory performing this test method should be evaluated in accordance with Practice C1093.
1.3Unless otherwise indicated, the values stated in inch-pound units are to be regarded as the standard. The values given in
parentheses are for information only.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C43 Terminology of Structural Clay Products
C126 Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
C150 Specification for Portland Cement
C1093 Practice for Accreditation of Testing Agencies for Masonry
E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Testing
3. Terminology
3.1 Definitions—Terminology E6 and Terminology C43 shall be considered as applying to the terms used in these test
methods.
4. Sampling
4.1 SelectionandPreparationofTestSpecimens—Forthepurposeofthesetests,full-sizebrick,tile,orsolidmasonryunitsshall
be selected by the purchaser or by the purchaser’s authorized representative. Specimens shall be representative of the lot of units
from which they are selected and shall include specimens representative of the complete range of colors, textures, and sizes and
shall be free of or brushed to remove dirt, mud, mortar, or other foreign materials unassociated with the manufacturing process.
—Forthepurposeofthesetests,full-sizebrick,tile,orsolidmasonryunitsshallbeselectedbythepurchaserorbythepurchaser’s
authorized representative. Specimens shall be representative of the lot of units from which they are selected and shall include
specimensrepresentativeofthecompleterangeofcolors,textures,andsizes.Specimensshallbefreeoforbrushedtoremovedirt,
mud,mortar,orotherforeignmaterialsunassociatedwiththemanufacturingprocess.Brushesusedtoremoveforeignmaterialshall
1
These test methods are under the jurisdiction of Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.02 on Brick and
Structural Clay Tile.
Current edition approved Dec.Nov. 1, 2007.2008. Published December 2007.November 2008. Originally approved in 1937. Last previous edition approved in 2007 as
C67–07a.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C67–08
have bristles of plastic (polymer) or horsehair. Wire brushes sh
...