ASTM C67-13
(Test Method)Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile
Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile
ABSTRACT
These test methods cover procedures for the sampling and testing of brick and structural clay tile. The tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate or absorption, and determination of weight, size, warpage, length chanange, and void areas. For purposes of these tests, full-size bricks, tiles, or solid masonry units shall be used as test specimens. They shall be representative of the lot of units from which they are to be selected in respect of the range of colors, textures, and sizes and shall be free of or brushed to remove dirt, mud, mortar, or other foreign materials unassociated with the manufacturing process.
SCOPE
1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void area. (Additional methods of test pertinent to ceramic glazed facing tile are included in Specification C126.)
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.Note 1—The testing laboratory performing this test method should be evaluated in accordance with Practice C1093.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C67 − 13 AmericanAssociation State Highway and Transportation
Officials Standard
AASHTO No.: T 32-70
Standard Test Methods for
1
Sampling and Testing Brick and Structural Clay Tile
ThisstandardisissuedunderthefixeddesignationC67;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* C1093Practice for Accreditation of Testing Agencies for
Masonry
1.1 These test methods cover procedures for the sampling
C1232Terminology of Masonry
and testing of brick and structural clay tile. Although not
E4Practices for Force Verification of Testing Machines
necessarily applicable to all types of units, tests include
E6Terminology Relating to Methods of Mechanical Testing
modulus of rupture, compressive strength, absorption, satura-
tion coefficient, effect of freezing and thawing, efflorescence,
3. Terminology
initial rate of absorption and determination of weight, size,
warpage,lengthchange,andvoidarea.(Additionalmethodsof
3.1 Definitions—For definitions relating to sampling and
test pertinent to ceramic glazed facing tile are included in
testingbrick,refertoTerminologyE6andTerminologyC1232.
Specification C126.)
4. Sampling
1.2 The text of this standard references notes and footnotes
which provide explanatory material.These notes and footnotes
4.1 Selection and Preparation of Test Specimens—For the
(excluding those in tables and figures) shall not be considered
purpose of these tests, full-size brick, tile, or solid masonry
as requirements of the standard.
units shall be selected by the purchaser or by the purchaser’s
NOTE 1—The testing laboratory performing this test method should be
authorizedrepresentative.Specimensshallberepresentativeof
evaluated in accordance with Practice C1093.
the lot of units from which they are selected and shall include
1.3 The values stated in inch-pound units are to be regarded
specimens representative of the complete range of colors,
as standard. The values given in parentheses are mathematical
textures, and sizes. Specimens shall be free of or brushed to
conversions to SI units that are provided for information only
remove dirt, mud, mortar, or other foreign materials unassoci-
and are not considered standard.
ated with the manufacturing process. Brushes used to remove
1.4 This standard does not purport to address all of the
foreign material shall have bristles of plastic (polymer) or
safety concerns, if any, associated with its use. It is the horsehair. Wire brushes shall not be used for preparing speci-
responsibility of the user of this standard to establish appro-
mens for testing. Specimens exhibiting foreign material that is
priate safety and health practices and determine the applica- not removed by brushing shall be discarded to ensure that
bility of regulatory limitations prior to use.
damaged or contaminated specimens are not tested.
4.2 Number of Specimens:
2. Referenced Documents
4.2.1 Brick—For the modulus of rupture, compressive
2
2.1 ASTM Standards:
strength, abrasion resistance, and absorption determinations, at
C126Specification for Ceramic Glazed Structural Clay Fac-
leasttenindividualbrickshallbeselectedforlotsof1000000
ing Tile, Facing Brick, and Solid Masonry Units
brick or fraction thereof. For larger lots, five additional
C150Specification for Portland Cement
specimensshallbeselectedfromeachadditional500000brick
or fraction thereof. Additional specimens are taken at the
1
discretion of the purchaser.
These test methods are under the jurisdiction of Committee C15 on Manufac-
tured Masonry Units and is the direct responsibility of Subcommittee C15.02 on
4.2.2 Structural Clay Tile—For the weight determination
Brick and Structural Clay Tile.
and for compressive strength and absorption tests, at least five
CurrenteditionapprovedJuly1,2013.PublishedJuly2013.Originallyapproved
tile shall be selected from each lot of 250 tons (226.8 Mg) or
in1937.Lastpreviouseditionapprovedin2012asC67–12.DOI:10.1520/C0067-
13.
fraction thereof. For larger lots, five additional specimens shall
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
be tested for each 500 tons (453.6 Mg) or fraction thereof. In
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
no case shall less than five tile be taken.Additional specimens
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. are taken at the discretion of the purchaser.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C67 − 12 C67 − 13 American Association State Highway and Transportation
Officials Standard
AASHTO No.: T 32-70
Standard Test Methods for
1
Sampling and Testing Brick and Structural Clay Tile
This standard is issued under the fixed designation C67; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily
applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of
freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void
area. (Additional methods of test pertinent to ceramic glazed facing tile are included in Specification C126.)
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
NOTE 1—The testing laboratory performing this test method should be evaluated in accordance with Practice C1093.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C126 Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
C150 Specification for Portland Cement
C1093 Practice for Accreditation of Testing Agencies for Masonry
C1232 Terminology of Masonry
E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Testing
3. Terminology
3.1 Definitions—TerminologyFor E6 and Terminologydefinitions relating to C1232 shall be considered as applying to
thesampling and testing brick, refer to Terminology E6 terms usedand Terminology C1232in these test methods.
4. Sampling
4.1 Selection and Preparation of Test Specimens—For the purpose of these tests, full-size brick, tile, or solid masonry units shall
be selected by the purchaser or by the purchaser’s authorized representative. Specimens shall be representative of the lot of units
from which they are selected and shall include specimens representative of the complete range of colors, textures, and sizes.
Specimens shall be free of or brushed to remove dirt, mud, mortar, or other foreign materials unassociated with the manufacturing
process. Brushes used to remove foreign material shall have bristles of plastic (polymer) or horsehair. Wire brushes shall not be
used for preparing specimens for testing. Specimens exhibiting foreign material that is not removed by brushing shall be discarded
to ensure that damaged or contaminated specimens are not tested.
1
These test methods are under the jurisdiction of Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.02 on Brick and
Structural Clay Tile.
Current edition approved June 1, 2012July 1, 2013. Published July 2012July 2013. Originally approved in 1937. Last previous edition approved in 20112012 as
C67 – 11.C67 – 12. DOI: 10.1520/C0067-12.10.1520/C0067-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C67 − 13
4.2 Number of Specimens:
4.2.1 Brick—For the modulus of rupture, compressive strength, abrasion resistance, and absorption determinations, at least ten
individual brick sha
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.