iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C584-81(1999)

(Test Method)

Standard Test Method for Specular Gloss of Glazed Ceramic Whitewares and Related Products

Standard Test Method for Specular Gloss of Glazed Ceramic Whitewares and Related Products

SCOPE
1.1 This test method covers the determination of 60° specular gloss of glazed ceramic whitewares and related products.  
1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Oct-1999
ICS
81.060.20 - Ceramic products
Technical Committee
C21 - Ceramic Whitewares and Related Products
Drafting Committee
C21.03 - Methods for Whitewares and Environmental Concerns
Current Stage
Ref Project

Relations

Replaced By
ASTM C584-81(2006) - Standard Test Method for Specular Gloss of Glazed Ceramic Whitewares and Related Products
Effective Date
15-Feb-2006
Referred By
ASTM E179-17(2022) - Standard Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials
Effective Date
10-Oct-1999

Buy Standard

ASTM C584-81(1999) - Standard Test Method for Specular Gloss of Glazed Ceramic Whitewares and Related ProductsASTM C584-81(1999) - Standard Test Method for Specular Gloss of Glazed Ceramic Whitewares and Related Products
PreviousNext
Standard
ASTM C584-81(1999) - Standard Test Method for Specular Gloss of Glazed Ceramic Whitewares and Related Products
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
Designation:C584 – 81(Reapproved1999)
Standard Test Method for
Specular Gloss of Glazed Ceramic Whitewares and Related
Products
This standard is issued under the fixed designation C 584; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
NOTE 1—If a greater degree of distinction between bright glazed
1. Scope
surfaces is desired, the 20° geometry instrument will provide it.
1.1 This test method covers the determination of 60° specu-
lar gloss of glazed ceramic whitewares and related products.
5. Apparatus
1.2 This standard does not purport to address all of the
5.1 Instrumental Components—The apparatus shall consist
safety concerns, if any, associated with its use. It is the
of an incandescent light source and lens furnishing an incident
responsibility of the user of this standard to establish appro-
beam of rays of required aperture, means for locating the
priate safety and health practices and determine the applica-
surface of the specimen, and a receptor located to receive the
bility of regulatory limitations prior to use.
required pyramid of rays reflected from the specimen. The
receptor shall be a photosensitive device having maximum
2. Referenced Documents
response near the middle of the visible region of the specimen.
2.1 ASTM Standards:
5.2 Geometric Conditions—The axis of the incident beam
D 523 Test Method for Specular Gloss
shall be 60° from the perpendicular to the specimen surface.
The axis of the receptor beam shall be coincident with the
3. Terminology
mirror image of the axis of the incident beam. A flat piece of
3.1 Definition:
polished black glass in the specimen position shall form an
3.1.1 specular gloss—the ratio of reflected to incident light,
image of the source in the center of the receptor window. The
times 1000, for specified apertures of illumination and recep-
length of the illuminated area of the specimen shall be equal to
tionwhentheaxisofreceptioncoincideswiththemirrorimage
notmorethanonethirdthedistancefromthecenterofthisarea
of the axis of illumination.
to the receptor field stop.The axis of the incident beam and the
axis of the receptor shall be within 0.1° of the nominal value
4. Significance and Use
indicated by the geometry. The dimensions and tolerances of
4.1 This test method provides a means of establishing
the source and receptor shall be as indicated in Table 1 (see
specular gloss limits for bright, semi-mat, and mat glazed
also Test Method D 523). The angular dimensions of the
surfaces. It is realized that specular gloss measurements do not
receptor field stop are measured from the receptor lens in a
always correlate well with visual rankings of glossiness be-
collimated-beam type instrument, and from the test surface in
cause specular gloss is only one of several related appearance
a converging-beam type instrument. See Fig. 1 for a general-
attributes that produce the sensation of gloss. However, the
ized illustration of the dimensions. The tolerances are chosen
prescribedtestmethodisofsufficientaccuracyfortheintended
so that errors of no more than one gloss unit at any point on the
purpose.
scale will result from errors in the source and receptor
apertures.
5.3 Vignetting—There shall be no vignetting of rays that lie
within the field angles specified in 5.2.
5.4 Spectral Conditions—Results should not differ signifi-
cantly from those obtained with a source-filter photocell
combination that is spectrally corrected to yield CIE luminous
This method is under the jurisdiction of ASTM Committee C-21 on Ceramic
efficiency with CIE Source C. Since specular reflection is, in
Whitewares and Related Products and is the direct responsibility of Subcommittee
C21.03 on Test Methods for Whiteware Properties.
Current edition approved Dec. 28, 1981. Published March 1982. Originally
published as C584 – 65 T. Last previous edition C584 – 81 (1994).
2 4
Annual Book of ASTM Standards, Vol 06.01. For more complete data see Hammond III, H. K., and Nimeroff, I.,“ Measure-
See Illing, A. M., “Comparison of Instrument Measurement and Visual ment of Sixty-Degree Specular Gloss,” Journal of Research, Nat. Bureau Standards,
Estimation of Specular Gloss of Glazed Ceramic Tile,” Materials Research & Vol 44, June 1950 ( RP 2105): also Hunter, R. S., “Gloss Evaluation of Materials,”
Standards, Vol 2, No. 2, Feb. 1962, p. 117. ASTM Bulletin, No. 186, December 1962.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
C584
TABLE 1 Angles and Relative Dimensions of Source Image and Receptors
In Plane of Measurement Perpendicular to Plane of Measurement
Relative Relative
u, deg 2 tan u/2 u, deg 2 tan u/2
Dimension Dimension
A
Source image tolerance 6 0.75 0.0131 0.171 3.0 0.0524 0.682
0.25 0.0044 0.057
60° receptor tolerance 6 4.4 0.0768 1.000 11.7 0.2049 2.668
0.1 0.0018 0.023 0.2 0.0035 0.046
A
Maximum; no minimum specification.
FIG. 1 Generalized Glossmeter Showing Apertures and Source Image Formation for a Collimated-Beam Type Instrument
general, spectrally nonselective, spectral corrections need
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1870-18(2024)(Test Method)
Standard Test Method for Determination of Impact Diameter from Falling Ball on Ceramic Tile

SIGNIFICANCE AND USE
4.1 Impact diameter may be used to interpret impact resistance.  
4.2 Maximum impact diameter may be a specified requirement for tile.
SCOPE
1.1 This test method covers procedures for measuring impact properties of ceramic tile, bonded to a standardized concrete substrate, from a falling 2-in. steel ball.  
1.2 This test method is intended solely for evaluating standardized laboratory test specimens and does not purport to simulate actual installed performance.  
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C373-18(2023)(Test Method)
Standard Test Methods for Determination of Water Absorption and Associated Properties by Vacuum Method for Pressed Ceramic Tiles and Glass Tiles and Boil Method for Extruded Ceramic Tiles and Non-tile Fired Ceramic Whiteware Products

SIGNIFICANCE AND USE
3.1 Measurement of density, porosity, and specific gravity is a tool for determining the degree of maturation of a ceramic body, or for determining structural properties that may be required for a given application.
SCOPE
1.1 These test methods covers procedures for determining water absorption, bulk density, apparent porosity, and apparent specific gravity of non-tile fired unglazed ceramic whiteware2 products, glazed or unglazed ceramic tiles, and glass tiles.  
1.2 The values stated in metric units are normative. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not normative.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM C674-13(2023)(Test Method)
Standard Test Methods for Flexural Properties of Ceramic Whiteware Materials

SIGNIFICANCE AND USE
3.1 These test methods provide a means for determining the modulus of rupture and the modulus of elasticity, which may be required in product specifications.
SCOPE
1.1 These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C242-21(Terminology)
Standard Terminology of Ceramic Whitewares and Related Products

SCOPE
1.1 This terminology pertains to the terminology used in ceramic whitewares and related products.  
1.2 Words adequately defined in standard dictionaries are not included. Included are words that are peculiar to this industry. Double words, hyphenated words, or phrases are listed alphabetically under the first word; additional important words are cross-referenced.  
1.3 For definitions of terms relating to surface imperfections on ceramics, refer to Terminology F109.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM F109-21(Terminology)
Standard Terminology Relating to Surface Imperfections on Ceramics

SCOPE
1.1 This terminology describes and illustrates imperfections observed on whitewares and related products. For additional definitions of terms relating to whitewares and related products, refer to Terminology C242. To observe these defects, examination shall be performed visually, with or without the aid of a dye penetrant, as described in Test Method C949. Agreement by the manufacturer and the purchaser regarding specific techniques of observation is strongly recommended.  
1.2 This terminology does not cover every defect or imperfection possible for whitewares or related products. The standard is not intended to be an all inclusive document for ceramic imperfections. New defect types may be created as ceramic processes, materials, and technology evolve.  
1.3 Some of the imperfection photos utilize magnification for clarity in documentation. Unless otherwise noted, typical observation conditions for detection of tile imperfections/defects shall consist of current ANSI A137.1 viewing criteria for the specific defect type  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    64 pages
    English language
    sale 15% off
  • Standard
    64 pages
    English language
    sale 15% off
ASTM
ASTM C738-94(2020)(Test Method)
Standard Test Method for Lead and Cadmium Extracted from Glazed Ceramic Surfaces

ABSTRACT
This test method details the standard and precise procedures for the determination of lead and cadmium extracted by acetic acid from glazed ceramic surfaces. The apparatus needed for this procedure include an atomic absorption spectrometer, lead and cadmium lamps, and glassware of chemical resistant borosilicate glass. The water, detergent wash, and reagents such as acetic acid, lead nitrate solution, hydrochloric acid, and cadmium solution should conform to chemical purity specified. Measurement procedures, precision, and bias are discussed thoroughly.
SCOPE
1.1 This test method covers the precise determination of lead and cadmium extracted by acetic acid from glazed ceramic surfaces. The procedure of extraction may be expected to accelerate the release of lead from the glaze and to serve, therefore, as a severe test that is unlikely to be matched under the actual conditions of usage of such ceramic ware. This test method is specific for lead and cadmium.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1466-00(2020)(Test Method)
Standard Test Method for Graphite Furnace Atomic Absorption Spectrometric Determination of Lead and Cadmium Extracted From Ceramic Foodware

SIGNIFICANCE AND USE
5.1 Toxic effects of lead and cadmium are well known and release of these elements from foodware is regulated by many countries. Regulatory decisions are based on results of 24-h leaching with acetic acid because results of this test method are precise and accurate and this test method is easy to use. Concentrations of lead and cadmium extracted by food may be different from results of this method, however, because acidity, contact time, and temperature typical of consumer use are different from those of this test method.  
5.2 This test method is intended for application only in contamination-free settings and should be performed by well-qualified technical personnel. It is recognized that it is not a practical or appropriate method to use in a nonlaboratory environment for quality assurance and control of the ceramic process. Users are advised to use Test Method C738 (flame AAS) for purposes of the latter.
SCOPE
1.1 This test method covers procedures for using graphite furnace atomic absorption spectroscopy (GFAAS) to quantitatively determine lead and cadmium extracted by acetic acid at room temperature from the food-contact surface of foodware. The method is applicable to food-contact surfaces composed of silicate-based materials (earthenware, glazed ceramicware, decorated ceramicware, decorated glass, and lead crystal glass) and is capable of determining lead concentrations greater than 0.005 to 0.020 μg/mL and cadmium concentrations greater than 0.0005 to 0.002 μg/mL, depending on instrument design.  
1.2 This test method also describes quality control procedures to check for contamination and matrix interference during GFAAS analyses and a specific sequence of analytical measurements that demonstrates proper instrument operation during the time period in which sample solutions are analyzed.  
1.3 Cleaning and other contamination control procedures are described in this test method. Users may modify contamination control procedures provided that the modifications produce acceptable results and are used for both sample and quality control analyses.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM C849-88(2020)(Test Method)
Standard Test Method for Knoop Indentation Hardness of Ceramic Whitewares

SIGNIFICANCE AND USE
5.1 The Knoop indentation hardness is one of many properties that is used to characterize ceramic whitewares. Attempts have been made to relate Knoop indentation hardness to tensile strength, grinding speeds, and other hardness scales, but no generally accepted methods are available. Such conversions are limited in scope and should be used with caution, except for special cases where a reliable basis for the conversion has been obtained by comparison tests.
SCOPE
1.1 This test method covers the determination of the Knoop indentation hardness of ceramic whitewares and the verification of Knoop indentation hardness testing machines using standard glasses.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C329-88(2020)(Test Method)
Standard Test Method for Specific Gravity of Fired Ceramic Whiteware Materials

SIGNIFICANCE AND USE
3.1 Measurement of specific gravity is a tool for determining the degree of maturation of a ceramic body.
SCOPE
1.1 This test method covers the determination of specific gravity of fired ceramic whiteware materials under prescribed conditions.  
Note 1: This test method is not applicable to materials attacked by water.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2442-75(2020)(Specification)
Standard Specification for Alumina Ceramics for Electrical and Electronic Applications

SCOPE
1.1 This specification covers the requirements for fabricated alumina parts suitable for electronic and electrical applications and ceramic-to-metal seals as used in electron devices. This specification specifies limits and methods of test for electrical, mechanical, thermal, and general properties of the bodies used for these fabricated parts, regardless of part geometry.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off