ASTM C110-02

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 110 – 02
Standard Test Methods for
Physical Testing of Quicklime, Hydrated Lime, and
1
Limestone
This standard is issued under the fixed designation C 110; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2. Referenced Documents
1.1 These test methods cover physical testing of quicklime 2.1 ASTM Standards:
and hydrated lime, and of limestone not otherwise covered in C 25 Test Methods for Chemical Analysis of Limestone,
2 3
ASTM standards. Quicklime, and Hydrated Lime
3
C 28 Specification for Gypsum Plasters
NOTE 1—Quicklime and hydrated lime have a high affinity for moisture
C 50 Practice for Sampling, Inspection, Packing, and Mark-
and carbon dioxide. Caution should be taken to protect both hydrated and
3
ing of Lime and Limestone Products
quicklime during sampling, storage, and testing (see Practice C 50).
C 51 Terminology Relating to Lime and Limestone (as used
1.2 The test procedures appear in the following order:
3
by the Industry)
Section
3
C 91 Specification for Masonry Cement
C 109 Test Method for Compressive Strength of Hydraulic
Air Entrainment 13
3
Apparent Loose Density of Hydrated Lime, Pulverized
Cement Mortars (Using 2-in. or 50-mm Cube Specimens)
Quicklime, and Limestone 16
C 117 Test Method for Material Finer than 75–Micrometre
Apparent Packed Density of Hydrated Lime, Pulverized
4
Quicklime, and Limestone 17 (No. 200) Sieve in Mineral Aggregates by Washing
Autoclave Expansion of Hydrated Lime 8
C 136 Test Method for Sieve Anlaysis of Fine and Coarse
Dry Brightness of Pulverized Limestone 15
4
Aggrgates
Dry Screening by Air Jet Sieve 19
3
Fineness of Pulverized Quicklime and Hydrated Lime by Air C 150 Specification for Portland Cement
Permeability 18
C 185 Test Method for Air Content of Hydraulic Cement
Limestone Grindability 20
3
Mortar
Particle Size of Pulverized Limestone 14
3
Plasticity of Lime Putty 7 C 188 Test Method for Density of Hydraulic Cement
Popping and Pitting of Hydrated Lime 9
C 204 Test Method for Fineness of Hydraulic Cement by
Residue and Sieve Analysis 5
3
Air Permeability Apparatus
Settling Rate of Hydrated Lime 11
Slaking Rate of Quicklime 12 C 207 Specification for Hydrated Lime for Masonry Pur-
Specific Gravity of Hydrated Lime Products 21 3
poses
Standard Consistency of Lime Putty 6
C 230 Specification for Flow Table for Use in Tests of
Water Retention of Hydrated Lime 10
3
Wet Sieve Analysis of Agricultural Liming Materials 22 Hydraulic Cement
C 305 Practice for Mechanical Mixing of Hydraulic Cement
1.3 The values stated in SI units are to be regarded as the
3
Pastes and Mortars of Plastic Consistency
standard.
C 430 Test Method for Fineness of Hydraulic Cement by
1.4 This standard does not purport to address all of the
3
the 45-μm (No. 325) Sieve
safety concerns, if any, associated with its use. It is the
C 472 Test Methods for Physical Testing of Gypsum, Gyp-
responsibility of the user of this standard to establish appro-
3
sum Plasters and Gypsum Concrete
priate safety and health practices and determine the applica-
C 670 Practice for Preparing Precision and Bias Statements
bility of regulatory limitations prior to use.
4
for Test Methods for Construction Materials
C 702 Practice for Reducing Field Samples of Aggregate to
4
Testing Size
3
1
These test methods are under the jurisdiction of ASTM Committee C07 on C 778 Specification for Standard Sand
Lime and are the direct responsibility of Subcommittee C07.06 on Physical Tests.
C 1005 Specification for Weights and Weighing Devices for
Current edition approved June 10, 2002. Published August 2002. Originally
3
Use in the Physical Testing of Hydraulic Cements
published as C 110 – 34 T. Last previous edition C 110 – 00a.
2
For tests on limestone as aggregate, see Vol 04.02 of the Annual Book of ASTM
Standards. For tests on limestone as building stone, see Vol 04.05 of the Annual
3
Annual Book of ASTM Standards, Vol 04.01.
Book of ASTM Standards.
4
Annual Book of ASTM Standards, Vol 04.02.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
C110
5
D 75 Practice for Sampling Aggregates 5.2.5 Attach a pressure gage to the water faucet and a rubber
E 11 Specification for Wire and Cloth Sieves for Testing
tubing to the output
...