ASTM C1157-02

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 1157 – 02
Standard Performance Specification for
1
Hydraulic Cement
This standard is issued under the fixed designation C 1157; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
2
1. Scope C 150 Specification for Portland Cement
C 151 Test Method for Autoclave Expansion of Portland
1.1 This specification covers hydraulic cements for both
2
Cement
general and special applications. This is a specification giving
C 183 Practice for Sampling and the Amount of Testing of
performance requirements. There are no restrictions on the
2
Hydraulic Cement
composition of the cement or its constituents.
C 185 Test Method for Air Content of Hydraulic Cement
1.2 The specification classifies cements by type based on
2
Mortar
specific requirements for general use, high early strength,
C 186 Test Method for Heat of Hydration of Hydraulic
resistance to attack by sulfates, and heat of hydration. Optional
2
Cement
requirements are provided for the property of low reactivity
2
C 188 Test Method for Density of Hydraulic Cement
with alkali-reactive aggregates.
C 191 Test Method for Time of Setting of Hydraulic Ce-
1.3 For properties where values are given in both SI and
2
ment by Vicat Needle
inch-pound units, the values in SI units are to be regarded as
C 204 Test Method for Fineness of Hydraulic Cement by
the standard. Values in SI units shall be obtained by measure-
2
Air Permeability Apparatus
ment in SI units or by appropriate conversion, using the Rules
2
C 219 Terminology Relating to Hydraulic Cement
for Conversion and Rounding given in Standard IEEE/ASTM
C 226 Specification for Air-Entraining Additions for Use in
SI 10, of measurements made in other units.
2
the Manufacture of Air-Entraining Hydraulic Cement
1.4 The text of this standard refers to notes and footnotes
C 227 Test Method for Potential Alkali Reactivity of
that provide explanatory material. These notes and footnotes
3
Cement-Aggregate Combinations (Mortar-Bar Method)
(excluding those in tables and figures) are not requirements of
C 311 Test Methods for Sampling and Testing Fly Ash or
the standard.
Natural Pozzolans for Use as a Mineral Admixture in
1.5 This standard does not purport to address all of the
3
Portland-Cement Concrete
safety concerns, if any, associated with its use. It is the
C 430 Test Method for Fineness of Hydraulic Cement by
responsibility of the user of this standard to establish appro-
2
the 45-μm (No. 325) Sieve
priate safety and health practices and determine the applica-
C 441 Test Method for Effectiveness of Mineral Admixtures
bility of regulatory limitations prior to use.
or Ground Blast-Furnace Slag in Preventing Excessive
NOTE 1—Specification C 150 is a prescription specification for portland 3
Expansion of Concrete Due to the Alkali-Silica Reaction
cement and specification C 595 is a specification for blended hydraulic
C 451 Test Method for Early Stiffening of Hydraulic Ce-
cement where the products that may be furnished are of restricted nature
2
ment (Paste Method)
and proportions and where the products must meet prescriptive require-
C 465 Specification for Processing Additions for Use in the
ments as to chemical and physical properties.
2
Manufacture of Hydraulic Cements
2
2. Referenced Documents
C 595 Specifications for Blended Hydraulic Cements
C 688 Specification for Functional Additions for Use in
2.1 ASTM Standards:
2
Hydraulic Cements
C 109/C 109M Test Method for Compressive Strength of
C 1012 Test Method for Length Change of Hydraulic-
Hydraulic Cement Mortars (Using 2-in. or 50-mm Cube
2
2
Cement Mortars Exposed to a Sulfate Solution
Specimens)
C 1038 Test Method for Expansion of Portland Cement
C 114 Test Methods for Chemical Analysis of Hydraulic
2
2
Mortar Bars Stored in Water
Cement
IEEE/ASTM SI 10 Standard for Use of the International
4
1
System of Units (SI): the Modern Metric System
This specification is under the jurisdiction of ASTM Committee C01 on
Cement and is the direct responsibility of Subcommittee C01.10 on Hydraulic
Cements for General Concrete Construction.
Current edition approved Aug. 10, 2002. Published September 2002. Originally
3
published as C 1157 – 92. Last previous edition C 1157 – 00a. Annual Book of ASTM Standards, Vol 04.02.
2 4
Annual Book of ASTM Standards, Vol 04.01. Annual Book of ASTM Standards, Vol 14.04.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Co
...