ASTM A307-03
(Specification)Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength
Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength
SCOPE
1.1 This specification covers the chemical and mechanical requirements of three grades of carbon steel bolts and studs in sizes 1/4 in. (6.35 mm) through 4 in. (104 mm). The fasteners are designated by "Grade" denoting tensile strength and intended use, as follows:Grade DescriptionGrade A Bolts and studs having a
minimum tensile strength of
60 ksi (414 MPa) and intended
for general applications,Grade B Bolts and studs having a
tensile strength of 60 to 100
ksi (414 to 690 MPa) and
intended for flanged joints in
piping systems with cast iron
flanges, andGrade C Nonheaded anchor bolts,
either bent or straight, having
properties conforming to
Specification A 36 (tensile
strength of 58 to 80 ksi (400
to 550 MPa)) and intended
for structural anchorage purposes.
1.1.1 The term studs includes stud stock, sometimes referred to as threaded rod.
1.2 This specification does not cover requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors or similar externally threaded fasteners.
1.3 Suitable nuts are covered in Specification A 563. Unless otherwise specified, the grade and style of nut for each grade of fastener, of all surface finishes, shall be as follows: Fastener Grade and Size Nut Grade and Style A, C, 1/4 to 1 1/2 in.A, hex A, C, over 1 1/2 to 4 in.A, heavy hex B, 1/ 4 to 4 in.A, heavy hex Nuts of other grades and styles having specified proof load stresses (Specification A 563, Table 3) greater than the specified grade and style of nut are also suitable.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 Supplementary Requirement S1 of an optional nature is provided, which describes additional restrictions to be applied when bolts are to be welded. It shall apply only when specified in the inquiry, order, and contract.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 307 – 03
Standard Specification for
1
Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength
This standard is issued under the fixed designation A 307; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
fication A 563, Table 3) greater than the specified grade and style of nut are also
1. Scope*
suitable.
2
1.1 This specification covers the chemical and mechanical
1.4 The values stated in inch-pound units are to be regarded
requirements of three grades of carbon steel bolts and studs in
as the standard. The values given in parentheses are for
1
sizes ⁄4 in. (6.35 mm) through 4 in. (104 mm). The fasteners
information only.
are designated by “Grade” denoting tensile strength and
1.5 Supplementary Requirement S1 of an optional nature is
intended use, as follows:
provided, which describes additional restrictions to be applied
Grade Description
when bolts are to be welded. It shall apply only when specified
in the inquiry, order, and contract.
Grade A Bolts and studs having a
1.6 Terms used in this specification are defined in Specifi-
minimum tensile strength of
60 ksi (414 MPa) and in-
cation F 1789 unless otherwise defined herein.
tended for general applica-
tions,
2. Referenced Documents
Grade B Bolts and studs having a
tensile strength of 60 to 100
2.1 ASTM Standards:
ksi (414 to 690 MPa) and
3
A 36/A 36M Specification for Carbon Structural Steel
intended for flanged joints in
piping systems with cast iron A 153/A 153M Specification for Zinc Coating (Hot-Dip) on
4
flanges, and
Iron and Steel Hardware
Grade C Nonheaded anchor bolts,
A 370 Test Methods and Definitions for Mechanical Testing
either bent or straight, hav-
5
ing properties conforming to of Steel Products
6
Specification A 36 (tensile
A 563 Specification for Carbon and Alloy Steel Nuts
strength of 58 to 80 ksi (400
A 706/A 706M Specification for Low-Alloy Steel De-
to 550 MPa)) and intended
3
for structural anchorage pur- formed Bars for Concrete Reinforcement
poses.
A 751 Test Methods, Practices, and Terminology for
5
Chemical Analysis of Steel Products
1.1.1 The term studs includes stud stock, sometimes re-
B 695 Specification for Coatings of Zinc Mechanically
ferred to as threaded rod.
7
Deposited on Iron and Steel
1.2 This specification does not cover requirements for
8
D 3951 Practice for Commercial Packaging
machine screws, thread cutting/forming screws, mechanical
F 606 Test Methods for Determining the Mechanical Prop-
expansion anchors or similar externally threaded fasteners.
erties of Externally and Internally Threaded Fasteners,
1.3 Suitable nuts are covered in Specification A 563. Unless
6
Washers, and Rivets
otherwise specified, the grade and style of nut for each grade of
F 1470 Guide for Fastener Sampling for Specified Mechani-
fastener, of all surface finishes, shall be as follows:
6
A cal Properties and Performance Inspection
Fastener Grade and Size Nut Grade and Style
6
1 1
A, C, ⁄4 to 1 ⁄2 in. A, hex
F 1789 Terminology for F16 Mechanical Fasteners
1
A, C, over 1 ⁄2 to 4 in. A, heavy hex
2.2 ANSI/ASME Standards:
1
B, ⁄4 to 4 in. A, heavy hex
9
B 1.1 Unified Screw Threads
A
Nuts of other grades and styles having specified proof load stresses (Speci-
3
Annual Book of ASTM Standards, Vol 01.04.
1 4
This specification is under the jurisdiction of ASTM Committee F16 on Annual Book of ASTM Standards, Vol 01.06.
5
Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts, Annual Book of ASTM Standards, Vol 01.03.
6
Nuts, Rivets, and Washers. Annual Book of ASTM Standards, Vol 01.08.
7
Current edition approved Oct. 1, 2003. Published October 2003. Originally Annual Book of ASTM Standards, Vol 02.05.
8
approved in 1947. Last previous edition approved in 2002 as A 307 – 02. Annual Book of ASTM Standards, Vol 15.09.
2 9
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
cation SA-307 in Section II of that Code. 4th Floor, New York, NY 10036.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A307–03
9
B 18.2.1 Square and Hex Bolts and Screws 4.5.4 When no preference is specified, the supplier may
10
B 18.24.1 Part Identifying Number (PIN) Code System furnish either a hot-dip zinc coating in accordance with
2.3 Military Standard: Specification A 153, Cla
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A307–02 Designation: A 307 – 03
Standard Specification for
1
Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength
This standard is issued under the fixed designation A307; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 Thisspecification coversthechemicalandmechanicalrequirementsofthreegradesofcarbonsteelboltsandstudsinsizes
1
⁄4 in. (6.35 mm) through 4 in. (104 mm). The fasteners are designated by “Grade” denoting tensile strength and intended use, as
follows:
Grade Description
Grade A Bolts and studs having a
minimum tensile strength of
60 ksi (414 MPa) and in-
tended for general applica-
tions,
Grade B Bolts and studs having a
tensile strength of 60 to 100
ksi (414 to 690 MPa) and
intended for flanged joints in
piping systems with cast iron
flanges, and
Grade C Nonheaded anchor bolts,
either bent or straight, hav-
ing properties conforming to
Specification A 36 (tensile
strength of 58 to 80 ksi (400
to 550 MPa)) and intended
for structural anchorage pur-
poses.
1.1.1 The term studs includes stud stock, sometimes referred to as threaded rod.
1.2 This specification does not cover requirements for machine screws, thread cutting/forming screws, mechanical expansion
anchors or similar externally threaded fasteners.
1.3 Suitable nuts are covered in Specification A563. Unless otherwise specified, the grade and style of nut for each grade of
fastener, of all surface finishes, shall be as follows:
A
Fastener Grade and Size Nut Grade and Style
1 1
A, C, ⁄4 to 1 ⁄2 in. A, hex
1
A, C, over 1 ⁄2 to 4 in. A, heavy hex
1
B, ⁄4to4in. A, heavy hex
A
Nuts of other grades and styles having specified proof load stresses (SpecificationA 563, Table 3) greater than the specified grade and style of nut are also suitable.
1.4 Thevaluesstatedininch-poundunitsaretoberegardedasthestandard.Thevaluesgiveninparenthesesareforinformation
only.
1.5 SupplementaryRequirementS1ofanoptionalnatureisprovided,whichdescribesadditionalrestrictionstobeappliedwhen
bolts are to be welded. It shall apply only when specified in the inquiry, order, and contract.
1.6 Terms used in this specification are defined in Specification F1789 unless otherwise defined herein.
2. Referenced Documents
2.1 ASTM Standards:
1
This specification is under the jurisdiction ofASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts, Nuts, Rivets,
and Washers.
Current edition approved Oct. 10, 2002. Published November 2002. Originally published as A307–47T. Last previous edition A307–00.
Current edition approved Oct. 1, 2003. Published October 2003. Originally approved in 1947. Last previous edition approved in 2002 as A307–02.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-307 in Section II of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A307–03
3
A36/A36M Specification for Carbon Structural Steel
4
A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
5
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
6
A563 Specification for Carbon and Alloy Steel Nuts
3
A706/A706M Specification for Low-Alloy Steel Deformed Bars for Concrete Reinforcement
5
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
7
B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
8
D3951 Practice for Commercial Packaging
F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and
6
Rivets
6
F1470Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection Guide for Fastener
6
Sampling for Specified Mechanical Properties and Performance Inspection
6
F1789 Terminology for F16 Mechanical Fasteners
2.2 ANSI/ASME Standards:
9
B1.1 Unified Screw Threads
9
B18.2.1 Square and Hex Bolts and Screws
10
B18.24.1 Part Identifying Number (PIN) Code System
2.3 Military Standard:
11
MIL-STD105 Single Sampling Plan for Normal Inspection
3. Ordering Information
3.1 Orde
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.