iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C990M-03

(Specification)

Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)

Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)

SCOPE
1.1 This specification covers joints for precast concrete pipe and box, and other sections using preformed flexible joint sealants for use in storm sewers and culverts which are not intended to operate under internal pressure, or are not subject to infiltration or exfiltration limits. Joint material used in horizontal applications is intended to prevent the flow of solids through the joint.
1.2 For precast concrete manhole sections, and other vertical structures, which are subject to internal or external pressure, infiltration or exfiltration limits are not prohibited from being specified. Joints in vertical structures covered by this specification are intended mainly to prevent the flow of solids or fluids through the joint.
1.3 This specification is to be used with pipe and structures conforming in all respects to Specifications C 14M, C 76M, C 478M, C 506M, C 507M, C 655M, C 985M, C 1504, and C 1433M, provided that if there is a conflict in permissible variations in dimensions, the requirements of this specification shall govern.
1.4 This specification is the metric companion of Specification C 990.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—This specification covers the material and performance of the joint and sealant only. Infiltration and exfiltration quantities for installed sections are dependent on factors other than the joints which must be covered by other specifications and suitable testing of the installed pipeline.

General Information

Status
Historical
Publication Date
09-Jan-2003
ICS
91.100.30 - Concrete and concrete products
Technical Committee
C13 - Concrete Pipe
Drafting Committee
C13.08 - Joints for Precast Concrete Structures
Current Stage
Ref Project

Relations

Replaces
ASTM C990M-01a - Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)
Effective Date
10-Jan-2003
Replaced By
ASTM C990M-03a - Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)
Effective Date
01-Nov-2003
Referred By
ASTM C1821/C1821M-16(2021)e1 - Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures
Effective Date
10-Jan-2003
Referred By
ASTM C655M-19a - Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)
Effective Date
10-Jan-2003
Referred By
ASTM C506M-22a - Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)
Effective Date
10-Jan-2003
Referred By
ASTM C76M-22a - Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)
Effective Date
10-Jan-2003
Referred By
ASTM C507M-22 - Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)
Effective Date
10-Jan-2003

Buy Standard

ASTM C990M-03 - Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)ASTM C990M-03 - Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)
PreviousNext
Technical specification
ASTM C990M-03 - Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 990M – 03
METRIC
Standard Specification for
Joints for Concrete Pipe, Manholes, and Precast Box
1
Sections Using Preformed Flexible Joint Sealants [Metric]
This standard is issued under the fixed designation C 990M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope C 14M Specification for Concrete Sewer, Storm Drain, and
2
Culvert Pipe
1.1 This specification covers joints for precast concrete pipe
C 76M Specification for Reinforced Concrete Culvert,
and box, and other sections using preformed flexible joint
2
Storm Drain, and Sewer Pipe
sealants for use in storm sewers and culverts which are not
C 478M Specification for Precast Reinforced Concrete
intended to operate under internal pressure, or are not subject
2
Manhole Sections
to infiltration or exfiltration limits. Joint material used in
C 506M Specification for Reinforced Concrete Arch Cul-
horizontal applications is intended to prevent the flow of solids
2
vert, Storm Drain, and Sewer Pipe
through the joint.
C 507M Specification for Reinforced Concrete Elliptical
1.2 For precast concrete manhole sections, and other verti-
2
Culvert, Storm Drain, and Sewer Pipe
cal structures, which are subject to internal or external pres-
C 655M Specification for Reinforced Concrete D-Load
sure, infiltration or exfiltration limits are not prohibited from
2
Culvert, Storm Drain, and Sewer Pipe
being specified. Joints in vertical structures covered by this
C 822 Terminology Relating to Concrete Pipe and Related
specification are intended mainly to prevent the flow of solids
2
Products
or fluids through the joint.
C 969 Practice for Infiltration and Exfiltration Acceptance
1.3 This specification is to be used with pipe and structures
2
Testing of Installed Precast Concrete Pipe Sewer Lines
conforming in all respects to Specifications C 14M, C 76M,
C 972 Test Method for Compression—Recovery of Tape
C 478M, C 506M, C 507M, C 655M, C 985M, C 1504, and
3
Sealant
C 1433M, provided that if there is a conflict in permissible
C 985M Specification for Nonreinforced Concrete Speci-
variations in dimensions, the requirements of this specification
2
fied Strength Culvert, Storm Drain, and Sewer Pipe
shall govern.
C 1433M Specification for Precast Reinforced Concrete
1.4 This specification is the metric companion of Specifica-
Box Sections for Culverts, Storm Drains, and Sewers
tion C 990.
2
[Metric]
1.5 This standard does not purport to address all of the
C 1504 Specification for Manufacture of Precast Reinforced
safety concerns, if any, associated with its use. It is the
Concrete Three-sided Structures for Culverts and Storm
responsibility of the user of this standard to establish appro-
2
Drains
priate safety and health practices and determine the applica-
4
D 4 Test Method for Bitumen Content
bility of regulatory limitations prior to use.
D 6 Test Method for Loss on Heating of Oil and Asphaltic
4
NOTE 1—This specification covers the material and performance of the
Compounds
joint and sealant only. Infiltration and exfiltration quantities for installed
D 36 Test Method for Softening Point of Bitumen (Ring-
sections are dependent on factors other than the joints which must be
4
and-Ball Apparatus)
covered by other specifications and suitable testing of the installed
D 71 Test Method for Relative Density of Solid Pitch and
pipeline.
4
Asphalt (Displacement Method)
2. Referenced Documents
D 92 Test Method for Flash Fire Points by Cleveland Open
5
Cup
2.1 ASTM Standards:
1
This specification is under the jurisdiction of ASTM Committee C13 on
2
Annual Book of ASTM Standards, Vol 04.05.
Concrete Pipe and is the direct responsibility of Subcommittee C13.08 on Rubber
3
Annual Book of ASTM Standards, Vol 04.07
Gaskets.
4
Annual Book of ASTM Standards, Vol 04.04.
Current edition approved January 10, 2003. Published July 2003. Originally
5
Annual Book of ASTM Standards, Vol 05.01.
approved in 1992. Last previous edition approved in 2001 as C 990M–01.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
C990M–03
6
D 113 Test Method for Ductility of Bituminous Materials 6.1.1 Bitumen sealants shall comply with the following
D 217 Test Method for Cone Penetration of Lubricating composition and physical requirements. Testing shall be in
5
Grease accordance with the methods prescribed in Section 9.
5
D 482 T
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1904-22(Test Method)
Standard Test Methods for Determination of the Effects of Biogenic Acidification on Concrete Antimicrobial Additives and/or Concrete Products

SIGNIFICANCE AND USE
4.1 As described in Guide C1894, the MIC of concrete is considered to be a three-stage process with the reduction in pH (Stage I) (for example, 12.5 > pH > 9-10), the establishment of biofilms which further lowers the pH (Stage II) (for example, 9-10 > pH > 4-6) and eventual deterioration due to biogenic acid exposure (Stage III) (for example,  
4.2 The tests are performed in simulated exposure solutions containing well-controlled bacterial strains that are grown in the laboratory. These tests do not require an environmental chamber and are intended to be performed as benchtop tests in biosafety level 1 laboratory conditions. These tests are suitable for simulation of the Stage II and III of MIC because the pH range of the solution can be controlled within the ranges of each stage.  
4.3 This standard provides three test methods.  
4.3.1 Test Method A is suitable for assessing the efficacy of antimicrobial admixtures in delaying or preventing biogenic acidification in a nutrient-rich simulated wastewater exposure solution.  
4.3.2 Test Method B is suitable for assessing the effectiveness of antimicrobial admixtures in a prescribed cementitious system (Option B1) or assessing the performance of different cementitious systems (Option B2) in delaying or preventing microbially-induced corrosion of concrete in the Stage II of MIC.  
4.3.3 Test Method C is suitable for assessing the suitability of cementitious systems in delaying or preventing microbially-induced corrosion of concrete in the Stage III of MIC.  
4.4 The results obtained by these test methods should serve as information to be used with Guide C1894 in, but not as the sole basis for, selection of a biologically-resistant material for a particular application. No attempt has been made to incorporate into these test methods all the various factors that may affect the performance of a material when subjected to actual service.
SCOPE
1.1 This standard presents test methods for the determination of the effects of biogenic acidification on concrete products and/or efficacy of antimicrobial products to resist microbially-induced corrosion (MIC) of concrete. In these tests, the biogenic acidification is achieved by sulfur-oxidizing bacteria (SOB) that can convert elemental sulfur or thiosulfate to sulfuric acid without the use of H2S gas.  
1.2 This standard is referenced in the guideline document for MIC of concrete products. Guide C1894 provides guidance for microbially-induced corrosion of concrete products and an overview of where this test, and its options, can and should be used. This document is not intended to be a guideline document for MIC of concrete products.  
1.3 This standard does not cover controlled breeding chamber tests, in which H2S gas is produced by bacterial activity and acidification is the result of the conversion of this H2S gas to sulfuric acid.  
1.4 This standard does not cover chemical acid immersion tests, in which acidification is achieved by chemical sulfuric acid addition, not by bacterial activity. Testing protocols for chemical acid immersion are described in Test Methods C267 and C1898.  
1.5 This standard does not cover tests that assess field exposure conditions or sewage pipe, concrete tank, or concrete riser network design.  
1.6 This standard does not cover live trial tests where concrete coupons or other specimens are monitored in sewers.  
1.7 The tests described in this standard should not be performed on concrete samples that have already been exposed to MIC conditions.  
1.8 This standard does not cover concrete deterioration due to chemical sulfate attack, which is caused by the reaction of sulfate compounds that exist in wastewater with the hydration products of cement. Test methods for assessing sulfate attack are provided by Test Methods C452 and C1012/C1012M.  
1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this ...

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM C1837-22(Specification)
Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures

ABSTRACT
This specification covers the procedures and test methods for the production of dry cast concrete, defined as very low slump or zero-slump concrete that requires continuous and intense vibration, or mechanical means, or a combination of vibration and mechanical means to consolidate the concrete, enabling immediate removal of the forms from the product. The placement, consolidation, curing, or protection of the concrete are not covered by this specification. The aggregates shall be sized, graded, proportioned, and mixed with such proportions of cementitious material, water, and admixtures, if any, to produce a thoroughly mixed concrete of such quality that the precast product will conform to the test and design requirements of the relevant specification. Materials covered by this specification are the following: cementitious materials (cement, slag cement, fly ash), allowable combinations of cementitious materials, aggregates, and admixtures and blends.
This specification also covers weigh batching and mixing, volumetric batching and continuous mixing, reporting, and strength of the specimen.
SCOPE
1.1 This specification covers the production of dry cast concrete as defined in 3.2.1. Requirements for quality of concrete shall be as hereinafter specified. This specification does not cover the placement, consolidation, curing, or protection of the concrete.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1894-22(Guide)
Standard Guide for Microbially Induced Corrosion of Concrete Products

SCOPE
1.1 This guide discusses microbially induced corrosion (MIC) of concrete products and laboratory test methods for determining the resistance of concrete to MIC. Although the guide is intended for concrete products, it also covers cementitious mortar and paste that are used in specialized applications or laboratory investigations.  
1.2 While this guide discusses concrete materials and admixtures, the document is not intended to specifically address field exposure conditions or sewage pipe, concrete tank, or concrete riser network design.  
1.3 This guide does not cover live trial tests where concrete coupons or other specimens are monitored in sewers.  
1.4 This guide does not cover concrete deterioration due to chemical sulfate attack, which is caused by the reaction of sulfate compounds that exist in wastewater with the hydration products of cement. Test methods for assessing sulfate attack are provided by Test Methods C452 and C1012/C1012M.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 The text of this guide references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM C1821/C1821M-16(2021)e1(Practice)
Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures

SIGNIFICANCE AND USE
4.1 This practice is useful as a reference by an owner and/or the engineer in preparing project specifications.  
4.2 The practice is useful as a reference by an owner, engineer, or installing contractor to properly install precast concrete circular manholes.
SCOPE
1.1 This practice covers the procedures to be followed in the planning, site preparation, installation, testing and backfilling of underground vertical reinforced circular precast concrete manholes and components manufactured in accordance with Specification C478/C478M and used in sewer, drainage, and water works.  
1.2 Concrete pipe and box culverts are not covered under this practice. Also, precast concrete utility structures covered in Specification C858 are excluded from this practice.  
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM C1577-20e1(Specification)
Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD

ABSTRACT
This specification covers single-cell precast reinforced concrete box sections cast monolithically and intended to be used for the construction of culverts and for the conveyance of storm water, industrial wastes and sewage. The reinforced concrete shall consist of cementitious materials, mineral aggregates and water, in which steel has been embedded in such a manner that the steel and concrete act together. The precast reinforced concrete box sections shall be produced with tongue and groove ends. The box section shall be cured using any of the following methods or combinations thereof: steam curing; water curing; and membrane curing. Compression tests for determining concrete compressive strength shall be allowed to be made on either standard rodded concrete cylinders or concrete cylinders compacted and cured in like manner as the box sections, or on cores drilled from the box section.
SCOPE
1.1 This specification covers single-cell precast reinforced concrete box sections cast monolithically and intended to be used for the construction of culverts and for the conveyance of storm water, industrial wastes and sewage.
Note 1: This specification is primarily a manufacturing and purchasing specification. However, standard designs per the AASHTO LRFD Bridge Design Specifications are included and the criteria used to develop these designs are given in Appendix X1. The successful performance of this product depends upon the proper selection of the box section, bedding, backfill, and care that the installation conforms to the construction specifications. The purchaser of the precast reinforced concrete box sections specified herein is cautioned that proper correlation of the loading conditions and the field requirements with the box section specified, and provision for inspection at the construction site, are required.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    24 pages
    English language
    sale 15% off
ASTM
ASTM C1898-20(Test Method)
Standard Test Methods for Determining the Chemical Resistance of Concrete Products to Acid Attack

SIGNIFICANCE AND USE
4.1 As described in Guide C1894, the MICC is considered to be a three-stage process with the reduction in pH (Stage I) (for example, 12.5 > pH > 9-10), the establishment of biofilms which further lowers the pH (Stage II) (for example, 9-10 > pH > 4-6) and eventual deterioration due to biogenic acid exposure (Stage III) (for example,  
4.2 As described in Guide C1894, acid immersion testing should be used with great caution in specifying concrete as this is a final stage of deterioration and the concrete may not be exposed to the conditions of this test.  
4.3 The results obtained by these test methods should serve as a guide in, but not as the sole basis for, selection of a chemical-resistant material for a particular application. No attempt has been made to incorporate into this test method all the various factors that may affect the performance of a material when subjected to actual service.
SCOPE
1.1 These test methods are intended to evaluate the chemical resistance of cement paste, mortar and concrete materials. This method is loosely based on Test Methods C267, however the solution is more rigorously defined and flexural strength is used. These test methods provide for the determination of changes in the following properties of the test specimens and test medium after exposure of the specimens to the medium:  
1.1.1 Mass of specimen,  
1.1.2 Appearance of specimen,  
1.1.3 Appearance of test medium, and  
1.1.4 Strength of specimens.  
1.2 Guide C1894 provides a standard guide for Microbially Induced Corrosion of Concrete (MICC) products. This standard is used for assessing the chemical resistance of cementitious products to acid attack caused by MICC; however as described in the guideline document for MICC products the current document only applies for Stage III of corrosion. This document is not intended to be a guideline document for the complete evaluation of MICC or for assessing the efficacy of antimicrobial additives used to reduce MICC.  
1.3 This standard supplements Test Methods C267 to improve the consistency of reported results for acids generated by MICC or other sources.  
1.4 This standard does not cover tests in which acidification is achieved by bacterial activity. Testing protocols for bacterial activity are described in Guide C1894.  
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to alternative units (typically inch-pound units) that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C990-09(2019)(Specification)
Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants

ABSTRACT
This specification covers joints for precast concrete pipe and box and other sections using preformed flexible joint sealants for use in storm sewers and culverts which are not intended to operate under internal pressure, or are not subject to infiltration or exfiltration limits. Joint material used in horizontal applications is intended to prevent the flow of solids through the joint. The acceptability of the pipe joint and sealant shall be determined by the results of the physical tests prescribed. Bitumen sealants shall be produced from asphalts, hydrocarbon resins and plasticizing compounds reinforced with inert mineral filler and shall contain no solvents. Butyl rubber sealants shall be produced from blends of butyl rubber and refined hydrocarbon resins and plasticizing compounds reinforced with inert mineral filler and shall contain no solvents. The joint design shall consist of a bell or groove on one end of the section and a spigot or tongue on the adjacent end of the joining section. The different test methods for the determination of the composition and physical properties of bitumen or butyl sealants are presented in details. The sections shall be tested hydrostatically in vertical alignment and a sufficient number of sections shall be assembled in straight alignment.
SCOPE
1.1 This specification covers joints for precast concrete pipe and box, and other sections using preformed flexible joint sealants for use in storm sewers and culverts which are not intended to operate under internal pressure, or are not subject to infiltration or exfiltration limits. Joint material used in horizontal applications is intended to prevent the flow of solids through the joint.  
1.2 For precast concrete manhole sections and other vertical structures, which are subject to internal or external pressure, infiltration or exfiltration limits are not prohibited from being specified. Joints in vertical structures covered by this specification are intended mainly to prevent the flow of solids or fluids through the joint.  
1.3 This specification is to be used with pipe and structures conforming in all respects to Specifications C14, C76, C478, C506, C507, C655, C985, C1433, C1504, and C1577, provided that if there is a conflict in permissible variations in dimensions, the requirements of this specification shall govern.  
1.4 This specification is the inch-pound companion to C990M; therefore, no SI equivalents are presented in the specification.
Note 1: This specification covers the material and performance of the joint and sealant only. Infiltration and exfiltration quantities for installed sections are dependent on factors other than the joints which must be covered by other specifications and suitable testing of the installed pipeline.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C990M-09(2019)(Specification)
Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)

ABSTRACT
This specification covers joints for precast concrete pipe and box and other sections using preformed flexible joint sealants for use in storm sewers and culverts which are not intended to operate under internal pressure, or are not subject to infiltration or exfiltration limits. Joint material used in horizontal applications is intended to prevent the flow of solids through the joint. The acceptability of the pipe joint and sealant shall be determined by the results of the physical tests prescribed. Bitumen sealants shall be produced from asphalts, hydrocarbon resins and plasticizing compounds reinforced with inert mineral filler and shall contain no solvents. Butyl rubber sealants shall be produced from blends of butyl rubber and refined hydrocarbon resins and plasticizing compounds reinforced with inert mineral filler and shall contain no solvents. The joint design shall consist of a bell or groove on one end of the section and a spigot or tongue on the adjacent end of the joining section. The different test methods for the determination of the composition and physical properties of bitumen or butyl sealants are presented in details. The sections shall be tested hydrostatically in vertical alignment and a sufficient number of sections shall be assembled in straight alignment.
SCOPE
1.1 This specification covers joints for precast concrete pipe and box and other sections using preformed flexible joint sealants for use in storm sewers and culverts which are not intended to operate under internal pressure, or are not subject to infiltration or exfiltration limits. Joint material used in horizontal applications is intended to prevent the flow of solids through the joint.  
1.2 Precast concrete manhole sections and other vertical structures that are subject to internal or external pressure, infiltration, or exfiltration limits are not prohibited from being specified. Joints in vertical structures covered by this specification are intended mainly to prevent the flow of solids or fluids through the joint.  
1.3 This specification is to be used with pipe and structures conforming in all respects to Specifications C14M, C76M, C478M, C506M, C507M, C655M, C985M, C1433M, C1504M, and C1577, provided that if there is a conflict in permissible variations in dimensions, the requirements of this specification shall govern.  
1.4 This specification is the metric companion of Specification C990.
Note 1: This specification covers the material and performance of the joint and sealant only. Infiltration and exfiltration quantities for installed sections are dependent on factors other than the joints which must be covered by other specifications and suitable testing of the installed pipeline.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1677-11a(2017)(Specification)
Standard Specification for Joints for Concrete Box, Using Rubber Gaskets

ABSTRACT
This specification covers flexible joints for concrete box sections, using rubber gaskets for leak resistant joints. The specification covers the design of joints and the requirements for rubber gaskets to be used. The gasket shall be fabricated from a rubber compound. The basic polymer shall be natural rubber, synthetic rubber, or a blend of both meeting the physical requirements prescribed. Gasket volume determination, non-circular shape gasket stretch height, and gasket length test methods shall be performed to determine the physical properties of the gastket in accordance with specified requirements. These test methods cover procedures for the mechanical testing of wrought and cast steels, stainless steels, and related alloys. Tension, bend, Rockwell hardness, portable hardness, brinell, and charpy impact tests shall be performed in accordance to specified requirements.
SCOPE
1.1 This specification covers flexible joints for concrete box sections, using rubber gaskets for leak resistant joints. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for boxes conforming in all other respects to Specification C1433 or C1577, provided that if there is conflict in permissible variations in dimensions the requirements of this specification for joints shall govern.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4791-19(2023)(Test Method)
Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate

SIGNIFICANCE AND USE
5.1 The particle shape of coarse aggregates influences the properties of some construction materials and may affect their placement and consolidation.  
5.2 This test method provides a means for checking compliance with specifications that limit such particles or to determine the relative shape characteristics of coarse aggregates.
SCOPE
1.1 This test method covers the determination of the percentages of flat particles, elongated particles, or flat and elongated particles in coarse aggregates. Two procedures, Method A and Method B, are presented in this standard. Method A is a reflection of the original procedure as developed prior to Superpave and is intended for all non-Superpave applications. Method B is a comparison of the maximum particle dimension to the minimum particle dimension and is intended for use with Superpave specifications.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.2.1 Exception (regarding sieves, per Specification E11)—The values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth. When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off