iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E162-12a

(Test Method)

Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source

Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source

SIGNIFICANCE AND USE
This test method provides a laboratory test procedure for measuring and comparing the surface flammability of materials when exposed to a prescribed level of radiant heat energy. It is intended for use in measurements of the surface flammability of materials exposed to fire. The test is conducted using small specimens that are representative, to the extent possible, of the material or assembly being evaluated. (Example: in terms of their thickness, layering, and any potential substrate.)  
The rate at which flames will travel along surfaces depends upon the physical and thermal properties of the material, product or assembly under test, the specimen mounting method and orientation, the type and level of fire or heat exposure, the availability of air, and properties of the surrounding enclosure.  
In this procedure, the specimens are subjected to one or more specific sets of laboratory fire test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.
If the test results obtained by this test method are to be considered as part of an overall assessment of fire hazard in a building or structure, then the example criteria, concepts and procedures incorporated into Guide E1546 shall be taken into consideration.
SCOPE
1.1 This fire-test-response standard describes the measurement of surface flammability of materials. It is not intended for use as a basis of ratings for building code purposes (see Appendix X1).
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazard is given in Section 7.
Note 1—There is no similar or equivalent ISO standard.

General Information

Status
Historical
Publication Date
14-Jan-2012
ICS
13.220.50 - Fire-resistance of building materials and elements
Technical Committee
E05 - Fire Standards
Drafting Committee
E05.22 - Surface Burning
Current Stage
Ref Project

Relations

Replaces
ASTM E162-11a - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
Effective Date
15-Jan-2012
Replaced By
ASTM E162-13 - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
Effective Date
15-May-2013
Referred By
ASTM D3574-17 - Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams
Effective Date
15-Jan-2012
Referred By
ASTM D8318-20 - Standard Specification for Low-Density Poly (Vinylidene Fluoride) Based Material Intended for Use in Wire and Cable Jacketing
Effective Date
15-Jan-2012
Referred By
ASTM E1321-18 - Standard Test Method for Determining Material Ignition and Flame Spread Properties
Effective Date
15-Jan-2012
Referred By
ASTM D4727/D4727M-22 - Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes
Effective Date
15-Jan-2012
Referred By
ASTM E84-23b - Standard Test Method for Surface Burning Characteristics of Building Materials
Effective Date
15-Jan-2012
Referred By
ASTM F3214-23 - Standard Practice for Characterization of Fire Properties of Seating, Upholstery, and Padding Materials for Vehicles Associated with Amusement Rides and Devices
Effective Date
15-Jan-2012
Referred By
ASTM E2280-21 - Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
Effective Date
15-Jan-2012
Referred By
ASTM E1317-19 - Standard Test Method for Flammability of Surface Finishes
Effective Date
15-Jan-2012
Referred By
ASTM F1085-19 - Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels
Effective Date
15-Jan-2012
Referred By
ASTM C647-19 - Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
Effective Date
15-Jan-2012
Referred By
ASTM E3020-22 - Standard Practice for Ignition Sources
Effective Date
15-Jan-2012
Referred By
ASTM E176-21ae1 - Standard Terminology of Fire Standards
Effective Date
15-Jan-2012
Referred By
ASTM D4000-23 - Standard Classification System for Specifying Plastic Materials
Effective Date
15-Jan-2012

Buy Standard

ASTM E162-12a - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy SourceASTM E162-12a - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
PreviousNext
Standard
ASTM E162-12a - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E162-12a - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy SourceREDLINE ASTM E162-12a - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
PreviousNext
Standard
REDLINE ASTM E162-12a - Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E162 − 12a AnAmerican National Standard
Standard Test Method for
Surface Flammability of Materials Using a Radiant Heat
1
Energy Source
This standard is issued under the fixed designation E162; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope E84Test Method for Surface Burning Characteristics of
Building Materials
1.1 This fire-test-response standard describes the measure-
E176Terminology of Fire Standards
mentofsurfaceflammabilityofmaterials.Itisnotintendedfor
E1546Guide for Development of Fire-Hazard-Assessment
use as a basis of ratings for building code purposes (see
Standards
Appendix X1).
3
2.2 ISO Standards
1.2 The values stated in inch-pound units are to be regarded
ISO13943Fire Safety—Vocabulary
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only 3. Terminology
and are not considered standard.
3.1 Definitions—For definitions of terms used in this test
1.3 This standard measures and describes the response of method, refer to the terminology contained in Terminology
E176 and ISO13943. In case of conflict, the definitions given
materials, products, or assemblies to heat and flame under
controlled conditions, but does not by itself incorporate all in Terminology E176 shall prevail.
factors required for fire hazard or fire risk assessment of the
3.2 Definitions of Terms Specific to This Standard:
materials, products, or assemblies under actual fire conditions.
3.2.1 flashing, n—flame fronts of 3 seconds or less in
1.4 This standard does not purport to address all of the duration.
safety concerns, if any, associated with its use. It is the 3.2.1.1 Discussion—All flame fronts, however temporary,
responsibility of the user of this standard to establish appro- are to be taken into account.
priate safety and health practices and determine the applica-
3.2.2 radiant panel index, I,n—the radiant panel index is
s
bility of regulatory limitations prior to use.
the product of the flame spread factor, F , and the heat
s
1.5 Fire testing of products and materials is inherently
evolution factor, Q.
hazardous,andadequatesafeguardsforpersonnelandproperty
4. Summary of Test Method
shall be employed in conducting these tests. This test method
may involve hazardous materials, operations, and equipment.
4.1 This test method of measuring surface flammability of
Specific information about hazard is given in Section 7.
materials employs a radiant heat source consisting of a 12 by
18-in. (305 by 457-mm) panel, in front of which an inclined 6
NOTE 1—There is no similar or equivalent ISO standard.
by 18-in. (152 by 457 mm) specimen of the material is placed.
2. Referenced Documents
The orientation of the specimen is such that ignition is forced
2
near its upper edge and the flame front progresses downward.
2.1 ASTM Standards:
D3675Test Method for Surface Flammability of Flexible
4.2 A factor derived from the rate of progress of the flame
Cellular Materials Using a Radiant Heat Energy Source
front and another derived from the rate of heat liberated by the
material under test are combined to provide a radiant panel
index.
1
This test method is under the jurisdiction of ASTM Committee E05 on Fire
Standards and is the direct responsibility of Subcommittee E05.22 on Surface
5. Significance and Use
Burning.
5.1 Thistestmethodprovidesalaboratorytestprocedurefor
Current edition approved Jan. 15, 2012. Published February 2012. Originally
approved in 1960. Last previous edition approved in 2012 as E162–12. DOI:
measuringandcomparingthesurfaceflammabilityofmaterials
10.1520/E0162-12A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from International Organization for Standardization (ISO), 1, ch. de
Standards volume information, refer to the standard’s Document Summary page on la Voie-Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http://
the ASTM website. www.iso.ch.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E162 − 12a
when exposed to a prescribed level of radiant heat energy. It is to center the specimen holder directly in front of the radiant
intended for use in measurements of the surface flammability panel. The support and bracing members shall be constructed
of materials exposed to fire. The test is conducted using small from
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:E162–12 Designation:E162–12a
Standard Test Method for
Surface Flammability of Materials Using a Radiant Heat
1
Energy Source
This standard is issued under the fixed designation E162; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This fire-test-response standard describes the measurement of surface flammability of materials. It is not intended for use
as a basis of ratings for building code purposes (see Appendix X1).
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled
conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products,
or assemblies under actual fire conditions.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.5 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be
employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific
information about hazard is given in Section 7.
NOTE 1—There is no similar or equivalent ISO standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D3675 Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source
E84 Test Method for Surface Burning Characteristics of Building Materials
E176 Terminology of Fire Standards
E1546 Guide for Development of Fire-Hazard-Assessment Standards
3
2.2 ISO Standards
ISO13943 Fire Safety—Vocabulary
3. Terminology
3.1 Definitions—For definitions of terms used in this test method, refer to the terminology contained inTerminology E176 and
ISO13943. In case of conflict, the definitions given in Terminology E176 shall prevail.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 flashing, n—flame fronts of 3 seconds or less in duration.
3.2.1.1 Discussion—All flame fronts, however temporary, are to be taken into account.
3.2.2 radiant panel index, I , n—the radiant panel index is the product of the flame spread factor, F , and the heat evolution
s s
factor, Q.
4. Summary of Test Method
4.1 This test method of measuring surface flammability of materials employs a radiant heat source consisting of a 12 by 18-in.
(305 by 457-mm) panel, in front of which an inclined 6 by 18-in. (152 by 457 mm) specimen of the material is placed. The
1
This test method is under the jurisdiction of ASTM Committee E05 on Fire Standards and is the direct responsibility of Subcommittee E05.22 on Surface Burning.
CurrenteditionapprovedJan.15,2012.PublishedFebruary2012.Originallyapprovedin1960.Lastpreviouseditionapprovedin20112012asE162–11a.E162–12.DOI:
10.1520/E0162-12A.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http://www.iso.ch.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E162–12a
orientation of the specimen is such that ignition is forced near its upper edge and the flame front progresses downward.
4.2 A factor derived from the rate of progress of the flame front and another derived from the rate of heat liberated by the
material under test are combined to provide a radiant panel index.
5. Significance and Use
5.1 This test method provides a laboratory test procedure for measuring and comparing the surface flammability of materials
when exposed t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2749-23(Practice)
Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens

SIGNIFICANCE AND USE
5.1 This practice describes a procedure to gather data intended to measure the uniformity of exposure conditions upon test specimens for the fire test methods described in Test Methods E119, E814, E1529, E1725, E1966 and E2336. The collected data from furnaces are intended to form a basis for performance requirements for the furnaces described in the referenced standards.  
5.2 This practice does not include requirements for furnace performance.  
5.3 In this procedure, the standardized test specimen is subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this procedure to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this procedure.  
5.4 The attention of all persons connected with the conduct of this practice is drawn to the fact that fire testing is hazardous and that there is a possibility that harmful smoke and gases are developed during the test. There is also a possibility that mechanical and operational hazards develop during the construction of the test specimen and the disposal of the test residues. An assessment of all potential hazards and risks to health shall be made and safety precautions shall be identified and provided. Written safety instructions shall be issued. Appropriate training shall be provided to relevant personnel. Laboratory personnel shall ensure that they follow written safety instructions at all times.
SCOPE
1.1 This standard provides general principles for measuring the uniformity of the furnace exposure on specimens tested in accordance with Test Methods E119, E814, E1529, E1725, E1966 and E2336.  
1.2 This practice specifies the materials and the construction requirements for a standardized test specimen used to provide a mounting surface for the instrumentation that measures furnace exposure.  
1.3 The instrumentation records temperatures, pressure differentials, and oxygen content near the exposed surface of the test specimen.  
1.4 The values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only.  
1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM E84-23c(Test Method)
Standard Test Method for Surface Burning Characteristics of Building Materials

SIGNIFICANCE AND USE
4.1 This test method is intended to provide only comparative measurements of surface flame spread and smoke density measurements with that of select grade red oak and fiber-cement board surfaces under the specific fire exposure conditions described herein.  
4.2 This test method exposes a nominal 24-ft (7.32 m) long by 20-in. (508 mm) wide specimen to a controlled air flow and flaming fire exposure adjusted to spread the flame along the entire length of the select grade red oak specimen in 51/2 min.  
4.3 This test method does not provide for the following:  
4.3.1 Measurement of heat transmission through the tested surface.  
4.3.2 The effect of aggravated flame spread behavior of an assembly resulting from the proximity of combustible walls and ceilings.  
4.3.3 Classifying or defining a material as noncombustible, by means of a flame spread index by itself.
SCOPE
1.1 This fire-test-response standard for the comparative surface burning behavior of building materials is applicable to exposed surfaces such as walls and ceilings. The test is conducted with the specimen in the ceiling position with the surface to be evaluated exposed face down to the ignition source. The material, product, or assembly shall be capable of being mounted in the test position during the test. Thus, the specimen shall either be self-supporting by its own structural quality, held in place by added supports along the test surface, or secured from the back side.  
1.2 Test Method E84 is a 10-min fire-test response method. The following standards address testing of materials in accordance with test methods that are applications or variations of the test method or apparatus used for Test Method E84:  
1.2.1 Materials required by the user to meet an extended 30-min duration tunnel test shall be tested in accordance with Test Method E2768.  
1.2.2 Wires and cables for use in air-handling spaces shall be tested in accordance with NFPA 262.  
1.2.3 Pneumatic tubing for control systems shall be tested in accordance with UL 1820.  
1.2.4 Combustible sprinkler piping shall be tested in accordance with UL 1887.  
1.2.5 Optical fiber and communications raceways for use in air handling spaces shall be tested in accordance with UL 2024.  
1.3 The purpose of this test method is to determine the relative burning behavior of the material by observing the flame spread along the specimen. Flame spread and smoke developed index are reported. However, there is not necessarily a relationship between these two measurements.  
1.4 The use of supporting materials on the underside of the test specimen has the ability to lower the flame spread index from those which might be obtained if the specimen could be tested without such support. These test results do not necessarily relate to indices obtained by testing materials without such support.  
1.5 Testing of materials that melt, drip, or delaminate to such a degree that the continuity of the flame front is destroyed, results in low flame spread indices that do not relate directly to indices obtained by testing materials that remain in place.  
1.6 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.  
1.8 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.9 This standard does not purport to address all of the safety concerns, if a...

  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    27 pages
    English language
    sale 15% off
ASTM
ASTM E2837-23(Test Method)
Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies

SIGNIFICANCE AND USE
5.1 This test method evaluates the following under the specified test conditions:  
5.1.1 The ability of a test specimen to undergo movement without reducing its fire resistance rating, and  
5.1.2 The duration for which a test specimen will contain a fire and retain its integrity during a predetermined fire resistive test exposure.  
5.2 This test method provides for the following measurements and evaluations where applicable:  
5.2.1 Ability of the test specimen  to movement cycle.  
5.2.2 Ability of the test specimen  to prohibit the passage of flames and hot gases.  
5.2.3 Transmission of heat through the test specimen.  
5.2.4 Ability of the test specimen  to resist the passage of water during a hose stream test.  
5.3 This test method does not provide the following:  
5.3.1 Any information about the rated wall assembly because its performance has already been determined.  
5.3.2 Evaluation of the degree by which the test specimen contributes to the fire hazard by generation of smoke, toxic gases, or other products of combustion.  
5.3.3 Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the test specimen.  
5.3.4 Measurement of flame spread over the surface of the test specimen.
Note 3: The information in 5.3.1 – 5.3.4 may be determined by other suitable fire resistive test methods. For example, 5.3.4 may be determined by Test Method E84.  
5.4 In this procedure, the test specimens are subjected to one or more specific tests under laboratory conditions. When different test conditions are substituted or the end-use conditions are changed, it is not always possible by, or from, this test method to predict changes to the characteristics measured. Therefore, the results are valid only for the exposure conditions described in this test method.
SCOPE
1.1 This fire-test-response test method measures the performance of a unique fire resistive joint system called a continuity head-of-wall joint system, which is designed to be used between a rated wall assembly and a nonrated horizontal assembly during a fire resistance test.  
1.2 This fire-test-response standard does not measure the performance of the following:  
1.2.1 The rated wall assembly, which is already established by other test methods, such as Test Method E119, or  
1.2.2 The nonrated horizontal assembly, which would be established by other test methods such as Test Method E119.
Note 1: Typically, rated wall assemblies obtain a fire resistance rating after being tested to Test Method E119, NFPA 251, UL 263, CAN/ULC-S101, or other similar fire resistive test methods.  
1.3 This fire-test-response standard is not intended to evaluate the connections between rated wall assemblies and nonrated horizontal assemblies  unless part of the continuity head-of-wall joint system.  
1.4 The fire resistive test end point is the period of time elapsing before the first performance criteria is reached when the continuity head-of-wall joint system is subjected to one of two time-temperature fire exposures.  
1.5 The fire exposure conditions used are either those specified by Test Method E119 for testing assemblies to standard time-temperature exposures or Test Method E1529 for testing assemblies to rapid-temperature rise fires.  
1.6 This test method specifies the heating conditions, methods of test, and criteria to establish a fire resistance rating only for a continuity head-of-wall joint system.  
1.7 Test results establish the performance of continuity head-of-wall joint systems to maintain continuity of fire resistance of the rated wall assembly where the continuity head-of-wall joint system interfaces with a nonrated horizontal assembly during the fire-exposure period.  
1.8 Test results shall not be construed as having determined the continuity head-of-wall joint system, nonrated horizontal assembly and the rated wall assembly’s suitability for use after that ...

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    English language
    sale 15% off
ASTM
ASTM E814-23a(Test Method)
Standard Test Method for Fire Tests of Penetration Firestop Systems

SIGNIFICANCE AND USE
5.1 This test method is used to determine the performance of a firestop system with respect to exposure to a standard time-temperature fire test and a hose stream test. The performance of a firestop system is dependent upon the specific assembly of materials tested including the number, type, and size of penetrations and the floors or walls in which it is installed.  
5.2 Two ratings shall be established for each firestop system. An F rating shall be based upon flame occurrence on the unexposed surface, while the T rating shall be based upon the temperature rise as well as flame occurrence on the unexposed side of the firestop system. These ratings, together with detailed performance data such as the location of through-openings and temperatures of penetrating items are intended to be one factor in assessing performance of firestop systems.
SCOPE
1.1 This test method is applicable to firestop systems of various materials and construction. Firestop systems are intended for use in openings in fire-resistive walls and floors that are evaluated in accordance with Test Methods E119.  
1.2 Tests conducted in conformance with this test method record firestop system performance during the test exposure; but such tests shall not be construed to determine suitability of the firestop system for use after test exposure.  
1.3 This test method also measures the resistance of firestop systems to an external force stimulated by a hose stream. However, this test method shall not be construed as determining the performance of the firestop system during actual fire conditions when subjected to forces such as failure of cable support systems and falling debris.  
1.4 The intent of this test method is to develop data to assist others in determining the suitability of the firestops for use where fire resistance is required.  
1.5 This test method does not apply to membrane penetrations of a floor-ceiling assembly or roof-ceiling assembly that are tested as part of the assembly in accordance with Test Methods E119.  
1.6 This test method does not apply to membrane penetrations of load-bearing walls.  
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.8 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of materials, products, or assemblies under actual fire conditions.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered requirements of the standard.  
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM E3367-23(Test Method)
Standard Test Method for Determining the Combustion Behavior of Layered Assemblies using a Cone Calorimeter

SIGNIFICANCE AND USE
5.1 Flammable liquid products can be generated by either pyrolysis or melting of polymers. Materials that generate flammable liquid products include thermoplastic polymers (for example, polyolefins) and thermosetting polymers (for example, polyurea and flexible polyurethane), which degrade to yield, in part, liquid pyrolyzates when pyrolyzing. Such liquid material can accumulate underneath a burning item and eventually ignite to form a pool fire, generally leading to a sharp increase in heat release rate and increase in fire hazard.  
5.2 Fire barriers are able to hinder the formation of a pool fire by delaying the generation and the release of flammable liquid products.  
5.3 This test method is intended to simulate the combustion of a central (that is, away from the edges) cross-section of a single material or a multi-layered product with ignition occurring on the top surface of the specimen.  
5.4 The test method is designed to assess whether liquid products are released during the test and the time at which they are released.  
5.5 The test method is designed to assess whether dripping occurs during the test and the time at which it occurs.  
5.6 The test method is designed to assess whether bottom ignition occurs during the test and the time at which it occurs.  
5.7 The test method is designed to assess whether pool ignition occurs during the test and the time at which it occurs.  
5.8 The test method is designed to assess whether burn-through occurs during the test and the time at which it occurs.  
5.9 The test measures heat release rate, mass loss rate and the resulting smoke obscuration as a result of exposing the specimen to a radiant heat source.  
5.10 The test method assesses whether the components of the specimen under examination demonstrates any of the following behaviors: breaking open, charring, appearance of superficial cracks without complete separation of the parts, melting, or shrinkage.  
5.11 The test method does not assess flame s...
SCOPE
1.1 This test method covers a means to measure the response of materials, products or layered assemblies when exposed to controlled levels of radiant heating, with or without an external ignitor.  
1.2 This test method provides an alternative test configuration to Test Method E1354 to measure the ignitability, heat release rate (including peak heat release rate and total heat released), mass loss rate, effective heat of combustion and visible smoke development.  
1.3 Compared to Test Method E1354, this test method adds the ability to measure the time at which the following phenomena occur: (1) appearance of liquid products (generated by either melting or pyrolysis of the specimen) underneath the sample, dripping and generation of a liquid pool underneath the specimen, (2) flaming over the bottom surface of the specimen and liquid pool, and; (3) burn-through.  
1.4 This test method is not intended to measure the response of products comprised of noncombustible cores.  
1.5 The top side of the specimens shall be exposed to an initial test heat flux of 0 kW/m2 to 75 kW/m2. External ignition, if any, shall be by electric spark.  
1.6 This test method has been developed for use to evaluate the fire test response characteristics of materials, products or layered assemblies. It is potentially useful for mathematical modeling, material or product design purposes, and research and development.  
1.7 This test method is used to measure and describe the response of assemblies to heat and flame under controlled conditions but does not by itself incorporate all factors required for fire hazard or fire risk assessment of an end-use product under actual fire conditions.  
1.8 This test method is used to measure the effect of fire barriers on the burning behavior of materials, products or layered assemblies to a range of radiant heat intensities but does not account for all factors that affect the performance of fire barriers at ...

  • Standard
    25 pages
    English language
    sale 15% off
ASTM
ASTM E2750-23(Guide)
Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM E814

SIGNIFICANCE AND USE
4.1 The methods and procedures set forth in this guide relate to the extension of the fire test results to firestop systems that have not been tested.  
4.2 Users of this guide must have knowledge and understanding of the provisions of Test Methods E119 and Test Method E814 including those pertaining to conditions of acceptance.  
4.3 In order to apply some of the principles described in this guide, reference to the original fire test report will be necessary.  
4.4 In Test Method E814, the specimens are subjected to specific laboratory fire test exposure conditions. Differences between the tested assembly and the as-built assembly impact the fire-test-response characteristics. Substitution of different test conditions also impacts the fire-test-response characteristics.  
4.5 The extension of data is valid only for the fire test exposure described in Test Method E814.  
4.6 This guide shall not be used to extrapolate the fire resistance rating to a higher value.  
4.7 Limitations:  
4.7.1 The extension of fire resistance data is to be used only for changes to the tested specimen that fall within normal and reasonable limits of accepted construction practices.  
4.7.2 Conclusions derived from using this guide are valid only if the identified change is the only change in the construction or properties of the components.  
4.7.3 Evaluation of changes to the fire-resistive assembly in which the firestop is installed is governed by the Extension of Data principles in Practice E2032.  
4.8 The statements in this guide are based on a single change to a system.
Note 2: It is possible that multiple changes have a different cumulative effect than that of individual changes evaluated separately. The principles contained herein may provide useful information for the application of sound engineering principles to evaluate the effect of multiple differences between tested and installed firestops.  
4.9 Extensions of data using this document shall be done by individ...
SCOPE
1.1 This guide covers the extension of results obtained from fire tests performed in accordance with Test Method E814 to applications that have not been tested. Test Method E814 evaluates the duration for which test specimens will contain a fire, retain their integrity, or both during a predetermined fire test exposure. Firestops are intended for use in fire-resistive walls and floors that are evaluated in conformance with Test Methods E119.
Note 1: Data obtained from firestops tested in accordance with Test Methods E119 with positive pressure can also be used.  
1.2 This guide is based on principles involving the extension of test data using simple considerations. The acceptance of these principles and their application is based substantially on an analogous worst-case proposition.  
1.3 These principles are only applicable to temperature conditions represented by the standard time-temperature curve described in Test Method E814, for systems falling within the scope of Test Method E814. This test method is a fire-test-response standard.  
1.4 The types of building constructions which are part of this guide are as follows: floors, walls, partitions, floor/ceiling and roof/ceiling assemblies.  
1.5 This guide applies to:  
1.5.1 a single penetrating item, or  
1.5.2 multiple penetrating items.  
1.6 This guide does not apply to joints systems tested to Test Methods E119, E1966, E2307, and E2837.  
1.7 Penetrating items can be one of the following: metallic pipe, non-metallic pipe, metallic tubing, non-metallic tubing, metallic conduit, non-metallic conduit, flexible metal conduit, cables, cable trays, bus ducts, insulated pipes, insulated tubing, insulated conduit, insulated and non-insulated ducts, and structural members.    
Metallic pipe, tubing or conduit  
6.7  
Insulated pipe, tubing or conduit  
6.8  
Non-metallic pipe, tubing or conduit  
6.9 and 6.10  
Flexible metal conduit  
6.11.1.4 and 6....

  • Guide
    8 pages
    English language
    sale 15% off
  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM E603-23(Guide)
Standard Guide for Room Fire Experiments

SIGNIFICANCE AND USE
5.1 This guide provides assistance for planning room fire tests. The object of each experiment is to evaluate the role of a material, product, or system in the fire growth within one or more compartments.  
5.2 The relationship between laboratory fire test methods and actual room fires can be investigated by the use of full-scale and reduced-scale experiments. This guide is aimed at establishing a basis for conducting full-scale experiments for the study of room fire growth.  
5.3 Room fire tests can be placed into four main categories: reconstruction, simulation, research and standardization.  
5.3.1 Reconstruction room fire tests are full scale replicates of a fire scene with the geometry, materials, contents, and ignition source intended to duplicate a particular scenario. The usual purpose of such a test is to evaluate what happened or what might happen in such a scenario.  
5.3.2 Simulation room fire tests are comparable to reconstruction fire tests, except that not all of the parameters are duplicated. A simulated fire test is one in which one or more components of a fire scenario are altered, usually in order to facilitate conducting the test. The compartment design must carefully address geometry and materials of construction to ensure that they do not significantly alter the fire response. Reconstruction and simulation fire tests often have a distinctive objective, such as time to flashover, that is related to the nature of the original fire scene.  
5.3.3 Research room fire tests are conducted in order to elucidate the effects of one or more of the following: geometry, materials, placement of items, ventilation, or other parameters. The measured effects (such as room temperature, heat flux, heat release rate, time to flashover, post flashover conditions) are chosen to provide the most useful information.  
5.3.4 Standardization room fire tests include scenarios that have been adopted by a standardization body. In this case, the compartment, ignition...
SCOPE
1.1 This guide addresses means of conducting full-scale fire experiments that evaluate the fire-test-response characteristics of materials, products, or assemblies under actual fire conditions.  
1.2 It is intended as a guide for the design of the experiment and for the use and interpretation of its results. The guide is also useful for establishing laboratory conditions that simulate a given set of fire conditions to the greatest extent possible.  
1.3 This guide allows users to obtain fire-test-response characteristics of materials, products, or assemblies, which are useful data for describing or appraising their fire performance under actual fire conditions.  
1.3.1 The results of experiments conducted in accordance with this guide are also useful elements for making regulatory decisions regarding fire safety requirements. The use for regulatory purposes of data obtained from experiments conducted using this guide requires that certain conditions and criteria be specified by the regulating authority.  
1.4 The rationale for conducting room fire experiments in accordance with this guide is shown in 1.5 – 1.8.  
1.5 Room fire experiments are a means of generating input data for computer fire models and for providing output data with which to compare modeling results.  
1.6 One of the major reasons for conducting room fire experiments is as an experimental means of assessing the potential fire hazard associated with the use of a material or product in a particular application. This should be borne in mind when designing nonstandard experiments.  
1.7 A rationale for conducting room fire experiments is the case when smaller-scale fire tests inadequately represent end-use applications.  
1.8 A further rationale for conducting room fire experiments is to verify the results obtained with smaller scale tests, to understand the scaling parameters for such tests.  
1.9 Room fire tests can be placed into four main cate...

  • Guide
    20 pages
    English language
    sale 15% off
  • Guide
    20 pages
    English language
    sale 15% off
ASTM
ASTM E1623-22a(Test Method)
Standard Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL)

SIGNIFICANCE AND USE
5.1 This test method is used primarily to determine the heat release rate of materials, products, and assemblies. Other parameters are the effective heat of combustion, mass loss rate, the time to ignition, smoke and gas production, emissivity, and surface temperature. Examples of test specimens are assemblies of materials or products that are tested in their end-use thickness. Therefore, the test method is suitable for assessing the heat release rate of a wall assembly.  
5.2 Representative joints and other characteristics of an assembly shall be included in a specimen when these details are part of normal design.  
5.3 This test method is applicable to end-use products not having an ideally planar external surface. The heat flux shall be adjusted to be that which is desired at the average distance of the surface from the radiant panel.  
5.4 In this procedure, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.  
5.5 Test Limitations:  
5.5.1 The test results have limited validity if: (a) the specimen melts sufficiently to overflow the drip tray, or (b) explosive spalling occurs.  
5.5.2 Exercise caution in interpreting results of specimens that sag, deform, or delaminate during a test. Report observations of such behavior.
SCOPE
1.1 This fire-test-response standard assesses the response of materials, products, and assemblies to controlled levels of radiant heat exposure with or without an external ignitor.  
1.2 The fire-test-response characteristics determined by this test method include the ignitability, heat release rates, mass loss rates, visible smoke development, and gas release of materials, products, and assemblies under well ventilated conditions.  
1.3 This test method is also suitable for determining many of the parameters or values needed as input for computer fire models. Examples of these values include effective heat of combustion, surface temperature, ignition temperature, and emissivity.  
1.4 This test method is also intended to provide information about other fire parameters such as thermal conductivity, specific heat, radiative and convective heat transfer coefficients, flame radiation factor, air entrainment rates, flame temperatures, minimum surface temperatures for upward and downward flame spread, heat of gasification, nondimensional heat of gasification (1)2 and the Φ flame spread parameter (see Test Method E1321). While some studies have indicated that this test method is suitable for determining these fire parameters, insufficient testing and research have been done to justify inclusion of the corresponding testing and calculating procedures.  
1.5 The heat release rate is determined by the principle of oxygen consumption calorimetry, via measurement of the oxygen consumption as determined by the oxygen concentration and flow rate in the exhaust product stream (exhaust duct). The procedure is specified in 11.1. Smoke development is quantified by measuring the obscuration of light by the combustion product stream (exhaust duct).  
1.6 Specimens are exposed to a constant heat flux in the range of 0 to 50 kW/m2  in a vertical orientation. Hot wires are used to ignite the combustible vapors from the specimen during the ignition and heat release tests. The assessment of the parameters associated with flame spread requires the use of line burners instead of hot wire ignitors.  
1.6.1 Heat release measurements at low heat flux levels (2) require special considerations as described in Section A1.1.6.  
1.7 This test method has been developed for evaluations, design, or research and development of materials, products, or...

  • Standard
    24 pages
    English language
    sale 15% off
  • Standard
    24 pages
    English language
    sale 15% off
ASTM
ASTM E2690-22(Practice)
Standard Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics

SIGNIFICANCE AND USE
5.1 Building products made with caulks and sealants are often used for applications for which Test Method E84 is used for compliance with building code, life safety code or mechanical code requirements. This practice describes, in detail, specimen mounting procedures for those caulks and sealants which are not able to be supported by their own structural characteristics during the test.  
5.2 Codes are often silent with regard to testing caulks and sealants for the assessment of flame spread index and smoke developed index as surface burning characteristics. This practice describes specimen preparation and mounting procedures for such materials and products.  
5.3 The material shall be representative of the materials used in actual field installations.  
5.4 The limitations for this procedure are those associated with Test Method E84.
SCOPE
1.1 This practice describes procedures for specimen preparation and mounting when testing caulks and sealants to assess flame spread and smoke development as surface burning characteristics using Test Method E84.  
1.1.1 Caulks and sealants up to 8 in. (203.2 mm) in width shall follow the requirements of 7.1.  
1.1.2 Caulks and sealants in excess of 8 in. (203.2 mm) in width shall follow the requirements of 7.2.
1.1.2.1 Caulks and sealants in excess of 8 in. (203.2 mm) in width can be considered coatings.  
1.2 This practice applies to caulks and sealants intended for various uses within buildings. The caulks and sealants addressed in this practice are not able to be supported by their own structural characteristics during the test.  
1.2.1 This practice does not apply to adhesives that are used to adhere or bind together surfaces. Annex A12 of Test Method E84 provides a procedure for testing adhesives.  
1.3 Testing is conducted in accordance with Test Method E84.  
1.4 This practice does not provide pass/fail criteria that can be used as a regulatory tool.  
1.5 This practice does not apply to materials for which the test specimen does not remain in place before and during the test until maximum flame propagation has occurred.  
1.6 This practice is not for system evaluation. It is for the comparison of the materials only.  
1.7 The results obtained by using this mounting procedure are confined to the materials themselves as tested and are not comparable to those obtained with materials that are tested in a full tunnel width application.  
1.8 This fire standard cannot be used to provide quantitative measures.  
1.9 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.10 This standard gives instructions on specimen preparation and mounting, but the fire-test-response method is given in Test Method E84. See also Section 9.  
1.11 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered requirements of the standard.  
1.12 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.13 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.14 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E2599-22(Practice)
Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics

SIGNIFICANCE AND USE
5.1 Reflective insulation, radiant barrier and vinyl stretch ceiling materials are evaluated in accordance with Test Method E84 to comply with building or mechanical code requirements. This practice describes, in detail, a specimen mounting procedure for reflective insulation, radiant barrier and vinyl stretch ceiling materials.  
5.2 The material shall be representative of the materials used in actual field installations.  
5.3 Specimen preparation and mounting procedures for materials not described in this practice shall be added as the information becomes available.  
5.4 The limitations for this procedure are those associated with Test Method E84.  
5.5 This practice shall not apply to rigid foam plastics with or without reflective facers.  
5.6 This practice shall not apply to site-fabricated stretch systems covered by Practice E2573.
SCOPE
1.1 This practice describes a procedure for specimen preparation and mounting when testing reflective insulation, radiant barrier and vinyl stretch ceiling materials to assess flame spread and smoke development as surface burning characteristics using Test Method E84.  
1.2 This practice is for reflective insulation materials and radiant barrier materials intended for mechanical fastening to substrates or building structural members, or intended to be mounted to a substrate with an adhesive.  
1.3 Specimens of reflective insulation materials and radiant barrier materials intended for mechanical fastening shall be prepared and mounted in accordance with 6.1. Specimens of reflective insulation materials and radiant barrier materials intended to be mounted to a substrate with an adhesive shall be prepared and mounted in accordance with 6.2. If the reflective insulation material or sheet radiant barrier material includes manufacturer recommended installation instructions with the option to be installed either by mechanical attachment or adhered, the insulation material shall be tested by both mounting procedures as outlined in 6.1 and 6.2.  
1.4 Specimens of vinyl stretch ceiling materials shall be prepared and mounted in accordance with 6.1.
Note 1: Vinyl stretch ceiling materials are mechanically fastened.  
1.5 This practice shall apply to reflective insulation materials and radiant barrier materials as defined in Section 3.  
1.6 This practice shall apply to reflective plastic core insulation materials as defined in 3.2.3. Reflective plastic core insulation materials are one specific type of reflective insulation materials.  
1.7 This practice shall apply to vinyl stretch ceiling materials as defined in Section 3.  
1.8 This practice shall not apply to rigid foam plastics with or without reflective facers.  
1.9 This practice shall not apply to site-fabricated stretch systems covered by Practice E2573.  
1.10 Testing is conducted in accordance with Test Method E84.  
1.11 This practice does not provide pass/fail criteria that can be used as a regulatory tool.  
1.12 Use the values stated in inch-pound units as the standard in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM SI-10 for further details.  
1.13 This fire standard cannot be used to provide quantitative measures.  
1.14 Fire testing of products and materials is inherently hazardous and adequate safeguards for personnel and property shall be employed in conducting these tests. Fire testing involves hazardous materials, operations and equipment. This practice gives instructions on specimen preparation and mounting but the fire-test-response method is given in Test Method E84. See also Section 8.  
1.15 The text of this practice references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered requirements of the standard.  
1.16 This standard does not purport to address all of the safety concerns, if any, associa...

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off