ASTM F3325-19
(Specification)Standard Specification for Leg-Protective Devices for Chainsaw Users
Standard Specification for Leg-Protective Devices for Chainsaw Users
SCOPE
1.1 This specification specifies minimum requirements for the design, performance, testing, and certification of protective clothing and protective devices designed to provide cut resistance protection to the legs of operators of power chainsaws.2
1.2 The objective of this specification is to prescribe fit, function, and performance criteria for protective clothing and protective devices that, when worn by chainsaw operators, are intended to reduce the severity of leg injuries caused by contact with a running power saw chain.
1.3 This standard is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.
1.4 Controlled laboratory tests used to determine compliance with the performance requirements of this standard shall not be deemed as establishing performance levels for all situations to which chainsaw operators may be exposed.
1.5 Mandatory requirements are indicated by the use of “shall”; recommendations and advisory information are indicated by the use of “should.”
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F3325 −19
Standard Specification for
1
Leg-Protective Devices for Chainsaw Users
This standard is issued under the fixed designation F3325; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.1.2.1 Discussion—The term authority having jurisdiction
is used in this document in a broad manner, since jurisdictions
1.1 This specification specifies minimum requirements for
and the responsibilities of approval agencies vary.
the design, performance, testing, and certification of protective
clothing and protective devices designed to provide cut resis- 2.1.3 certification, n—a system whereby an organization
2
tance protection to the legs of operators of power chainsaws. determines that a manufacturer has demonstrated the ability to
make a product that complies with the requirements of the
1.2 The objective of this specification is to prescribe fit,
specification, authorizes the manufacturer to use a label on
function, and performance criteria for protective clothing and
products that comply with the requirements of the
protective devices that, when worn by chainsaw operators, are
specification, and conducts a follow-up to verify the methods
intendedtoreducetheseverityofleginjuriescausedbycontact
the manufacturer uses to determine compliance with the
with a running power saw chain.
requirements of this specification.
1.3 This standard is not intended to serve as a detailed
2.1.4 certification organization, n—an independent, third-
manufacturing or purchasing specification, but can be refer-
party organization that determines product compliance with the
enced in purchase contracts to ensure that minimum perfor-
requirements of the specification with a labeling and listing
mance requirements are met.
follow-up program.
1.4 Controlled laboratory tests used to determine compli-
2.1.5 chainsaw, n—a portable, power-operated tool used for
ance with the performance requirements of this standard shall
cutting wood that has cutters linked in a chain.
not be deemed as establishing performance levels for all
2.1.6 chain speed, n—the speed of synchronized movement
situations to which chainsaw operators may be exposed.
of linked cutters around a guide bar and sprocket.
1.5 Mandatory requirements are indicated by the use of
2.1.7 chain stop, n—for chainsaw cut resistance, the result-
“shall”; recommendations and advisory information are indi-
ing action when a material clogs (jams) the drive sprocket or
cated by the use of “should.”
slows the speed sufficiently to prevent advancement of the saw
1.6 This international standard was developed in accor-
chain.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the 2.1.8 cut resistance, n—in chainsaw testing, the ability of a
Development of International Standards, Guides and Recom- material, while in contact with the linked cutters, to resist
mendations issued by the World Trade Organization Technical cut-through by the cutters of a moving saw chain, independent
Barriers to Trade (TBT) Committee. of either jamming or chain stop.
2.1.9 cut-through, n—for chainsaw cut resistance,theaction
2. Terminology
of a running chainsaw after complete breakthrough of either
2.1 Definitions:
protective garment or protective device.
2.1.1 approve, v—to be acceptable to the authority having
2.1.10 cut-through time, n—for chainsaw cut resistance, the
jurisdiction.
time required for a running saw chain to effect complete
2.1.2 authority having jurisdiction, n—the organization,
breakthrough of a protective garment or protective device.
office, or individual responsible for approving any equipment,
2.1.11 follow-up program, n—the sampling, inspection,
installation, or procedure.
tests, or other measures conducted by the certification organi-
zation on a periodic basis to determine the continued compli-
1
This specification is under the jurisdiction of ASTM Committee F23 on
anceofproductsthatarebeingmadebythemanufacturertothe
Personal Protective Clothing and Equipment and is the direct responsibility of
requirements of the standard specification.
Subcommittee F23.20 on Physical.
Current edition approved Feb. 1, 2019. Published March 2019. Originally
2.1.12 jamming, n—for chainsaw cut resistance, the clog-
approved in 2018. Last previous edition approved in 2018 as F3325 – 18. DOI:
ging action manifested by a protective garment that can
10.1520/F3325-19.
2
This was developed as a replacement for the archived CAN/BNQ 1923-450. produce a chain stop.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken,
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F3325 − 18 F3325 − 19
Standard Specification for
1
Leg-Protective Devices for Chainsaw Users
This standard is issued under the fixed designation F3325; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification specifies minimum requirements for the design, performance, testing, and certification of protective
2
clothing and protective devices designed to provide cut resistance protection to the legs of operators of power chainsaws.
1.2 The objective of this specification is to prescribe fit, function, and performance criteria for protective clothing and protective
devices that, when worn by chainsaw operators, are intended to reduce the severity of leg injuries caused by contact with a running
power saw chain.
1.3 This standard is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in
purchase contracts to ensure that minimum performance requirements are met.
1.4 Controlled laboratory tests used to determine compliance with the performance requirements of this standard shall not be
deemed as establishing performance levels for all situations to which chainsaw operators may be exposed.
1.5 Mandatory requirements are indicated by the use of “shall”; recommendations and advisory information are indicated by
the use of “should.”
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Terminology
2.1 Definitions:
2.1.1 approve, v—to be acceptable to the authority having jurisdiction.
2.1.2 authority having jurisdiction, n—the organization, office, or individual responsible for approving any equipment,
installation, or procedure.
2.1.2.1 Discussion—
The term authority having jurisdiction is used in this document in a broad manner, since jurisdictions and the responsibilities of
approval agencies vary.
2.1.3 certification, n—a system whereby an organization determines that a manufacturer has demonstrated the ability to make
a product that complies with the requirements of the specification, authorizes the manufacturer to use a label on products that
comply with the requirements of the specification, and conducts a follow-up to verify the methods the manufacturer uses to
determine compliance with the requirements of this specification.
2.1.4 certification organization, n—an independent, third-party organization that determines product compliance with the
requirements of the specification with a labeling and listing follow-up program.
2.1.5 chainsaw, n—a portable, power-operated tool used for cutting wood that has cutters linked in a chain.
2.1.6 chain speed, n—the speed of synchronized movement of linked cutters around a guide bar and sprocket.
2.1.7 chain stop, n—for chainsaw cut resistance, the resulting action when a material clogs (jams) the drive sprocket or slows
the speed sufficiently to prevent advancement of the saw chain.
1
This specification is under the jurisdiction of ASTM Committee F23 on Personal Protective Clothing and Equipment and is the direct responsibility of Subcommittee
F23.20 on Physical.
Current edition approved Aug. 15, 2018Feb. 1, 2019. Published September 2018March 2019. Originally approved in 2018. Last previous edition approved in 2018 as
F3325 – 18. DOI: 10.1520/F3325-18.10.1520/F3325-19.
2
This was developed as a replacement for the archived CAN/BNQ 1923-450.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F3325 − 19
2.1.8 cut resistance, n—in chainsaw testing, the ability of a material, while in contact with the linked cutters, to resist
cut-through by the cutters of a moving saw chain, independent of either jamming or chain stop.
2.1.9 cut-through, n—for chainsaw cut resistance, the action of a running chainsaw after complete breakthrough of either
protective garment or protective device.
2.1.10 cut-through time, n—for chainsaw cut resistance, the time required for a running saw chain to effect complete
breakthrough of a protective garment o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.