ASTM F1821-18
(Specification)Standard Consumer Safety Specification for Toddler Beds
Standard Consumer Safety Specification for Toddler Beds
ABSTRACT
This consumer safety specification deals with the requirements for the design and performance of toddler beds. It also contains requirements for labeling and instructional material. This consumer safety specification is intended to minimize incidents to children resulting from normal use and reasonably foreseeable misuse of toddler beds. It does not address incidents resulting from alteration or unreasonable misuse. Materials shall be tested and shall conform to requirements of small parts, paint and surface coating, scissoring, shearing, and pinching, protective components, openings, labeling, corner post extensions, mattress retention, mattress support system, mattress support system attachment to end structures, guardrails, end structures, partially bounded openings, and permanency of labels and warnings.
SCOPE
1.1 This consumer safety specification covers requirements for the design and performance of toddler beds. It also contains requirements for labeling and instructional material.
1.2 This consumer safety specification is intended to minimize incidents to children resulting from normal use and reasonably foreseeable misuse of toddler beds. It does not address incidents resulting from alteration or unreasonable misuse.
1.3 For the purposes of this consumer safety specification, a toddler bed is a bed that is sized to accept a full-size crib mattress and is intended for use by a child not less than 15 months of age and who weighs no more than 50 lb (27.7 kg).
1.4 No toddler bed produced after the approval date of this consumer safety specification shall indicate compliance with this specification, either by label or by other means, unless it conforms to all the requirements contained herein.
1.5 This consumer safety specification includes the following sections:
Scope
Section 1
Referenced Documents
Section 2
Terminology
Section 3
Calibration and Standardization
Section 4
General Requirements
Section 5
Performance Requirement
Section 6
Test Methods
Section 7
Marking and Labeling
Section 8
Instructional Literature
Section 9
Keywords
Section 10
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1821 −18
Standard Consumer Safety Specification for
1
Toddler Beds
This standard is issued under the fixed designation F1821; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety specification addresses toddler bed incidents that were identified by the
Consumer Product Safety Commission (CPSC).
Inresponsetoincidentdatasuppliedbythecommission,thisconsumersafetyspecificationattempts
to minimize: entrapment in bed end structures, entrapment between the guardrail and side rail, and
entrapment in the mattress support system. Entrapment of a child’s head or neck can result in
asphyxiation. It also addresses corner post extensions, which may catch pacifier cords, ribbons,
necklaces, or clothing that a child may be wearing and which may be caught on a projection.
This consumer safety specification is written in accordance with the current available state-of-the-
art technology and will be updated whenever substantive information becomes available that
necessitates additional requirements or justifies a revision to existing requirements.
1. Scope
General Requirements Section 5
Performance Requirement Section 6
1.1 This consumer safety specification covers requirements
Test Methods Section 7
for the design and performance of toddler beds. It also contains Marking and Labeling Section 8
Instructional Literature Section 9
requirements for labeling and instructional material.
Keywords Section 10
1.2 This consumer safety specification is intended to mini-
1.6 The values stated in inch-pound units are to be regarded
mize incidents to children resulting from normal use and
as standard. The values given in parentheses are mathematical
reasonably foreseeable misuse of toddler beds. It does not
conversions to SI units that are provided for information only
address incidents resulting from alteration or unreasonable
and are not considered standard.
misuse.
1.7 The following safety hazards caveat pertains only to the
1.3 For the purposes of this consumer safety specification, a
test methods portion, Section 7, of this consumer safety
toddler bed is a bed that is sized to accept a full-size crib
specification: This standard does not purport to address all of
mattress and is intended for use by a child not less than 15
the safety concerns, if any, associated with its use. It is the
months of age and who weighs no more than 50 lb (27.7 kg).
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
1.4 No toddler bed produced after the approval date of this
mine the applicability of regulatory limitations prior to use.
consumer safety specification shall indicate compliance with
1.8 This international standard was developed in accor-
this specification, either by label or by other means, unless it
dance with internationally recognized principles on standard-
conforms to all the requirements contained herein.
ization established in the Decision on Principles for the
1.5 This consumer safety specification includes the follow-
Development of International Standards, Guides and Recom-
ing sections:
mendations issued by the World Trade Organization Technical
Scope Section 1
Barriers to Trade (TBT) Committee.
Referenced Documents Section 2
Terminology Section 3
2. Referenced Documents
Calibration and Standardization Section 4
2
2.1 ASTM Standards:
D3359 Test Methods for Rating Adhesion by Tape Test
1
This consumer safety specification is under the jurisdiction ofASTM Commit-
tee F15 on Consumer Products and is the direct responsibility of Subcommittee
2
F15.18onCribs,ToddlerBeds,PlayYards,Bassinets,CradlesandChangingTables. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Dec. 1, 2018. Published December 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1997. Last previous edition approved in 2016 as F1821 – 16. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F1821-18. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1821−18
D3574 Test Methods for Flexible Cellular Materials—Slab, 3.1.9 paper labels, n—any label which tears without the aid
Bonded, and Molded Urethane Foams of tools and leaves a fibrous edge.
F1169 Consumer Safety Specification for Full-Size Baby
3.1.10 partially bounded openings, n—any opening in a
Cribs
toddler bed that is not totall
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1821 − 16 F1821 − 18
Standard Consumer Safety Specification for
1
Toddler Beds
This standard is issued under the fixed designation F1821; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety specification addresses toddler bed incidents that were identified by the
Consumer Product Safety Commission (CPSC).
In response to incident data supplied by the commission, this consumer safety specification attempts
to minimize: entrapment in bed end structures, entrapment between the guardrail and side rail, and
entrapment in the mattress support system. Entrapment of a child’s head or neck can result in
asphyxiation. It also addresses corner post extensions, which may catch pacifier cords, ribbons,
necklaces, or clothing that a child may be wearing and which may be caught on a projection.
This consumer safety specification is written in accordance with the current available state-of-the-
art technology and will be updated whenever substantive information becomes available that
necessitates additional requirements or justifies a revision to existing requirements.
1. Scope
1.1 This consumer safety specification covers requirements for the design and performance of toddler beds. It also contains
requirements for labeling and instructional material.
1.2 This consumer safety specification is intended to minimize incidents to children resulting from normal use and reasonably
foreseeable misuse of toddler beds. It does not address incidents resulting from alteration or unreasonable misuse.
1.3 For the purposes of this consumer safety specification, a toddler bed is a bed that is sized to accept a full-size crib mattress
and is intended for use by a child not less than 15 months of age and who weighs no more than 50 lb (27.7 kg).
1.4 No toddler bed produced after the approval date of this consumer safety specification shall indicate compliance with this
specification, either by label or by other means, unless it conforms to all the requirements contained herein.
1.5 This consumer safety specification includes the following sections:
Scope Section 1
Referenced Documents Section 2
Terminology Section 3
Calibration and Standardization Section 4
General Requirements Section 5
Performance Requirement Section 6
Test Methods Section 7
Marking and Labeling Section 8
Instructional Literature Section 9
Keywords Section 10
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this consumer safety
specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and
determine the applicability of regulatory limitations prior to use.
1
This consumer safety specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee F15.18
on Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Changing Tables.
Current edition approved Oct. 1, 2016Dec. 1, 2018. Published October 2016December 2018. Originally approved in 1997. Last previous edition approved in 20152016
as F1821 – 15.F1821 – 16. DOI: 10.1520/F1821-16.10.1520/F1821-18.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1821 − 18
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D3359 Test Methods for Rating Adhesion by Tape Test
D3574 Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams
F1169 Consumer Safety Specification for Full-Size Baby Cribs
3
2.2 Code of Federal Regulations:
16 CFR 1303 Ban of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.