ASTM E2104-22

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E2104 − 15 E2104 − 22
Standard Practice for
Radiographic Examination of Advanced Aero and Turbine
1
Materials and Components
This standard is issued under the fixed designation E2104; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice establishes the minimum requirements for radiographic examination of metallic and nonmetallic materials and
components used in designated applications such as gas turbine engines and flight structures.
1.2 The requirements in this practice are intended to control the radiographic process to ensure the quality of radiographic images
produced for use in designated applications such as gas turbine engines and flight structures; this practice is not intended to
establish acceptance criteria for material or components. When examination is performed in accordance with this practice,
engineering drawings, specifications, or other applicable documents shall indicate the acceptance criteria.
1.3 All areas of this practice may be open to agreement between the cognizant engineering organization and the supplier, or
specific direction from the cognizant engineering organization.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E543 Specification for Agencies Performing Nondestructive Testing
E747 Practice for Design, Manufacture and Material Grouping Classification of Wire Image Quality Indicators (IQI) Used for
Radiology
E999 Guide for Controlling the Quality of Industrial Radiographic Film Processing
E1025 Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI)
Used for Radiography
E1030E1030/E1030M Practice for Radiographic Examination of Metallic Castings
E1032 Practice for Radiographic Examination of Weldments Using Industrial X-Ray Film
E1079 Practice for Calibration of Transmission Densitometers
1
This practice is under the jurisdiction of ASTM Committee E07 on Nondestructive Testing and is the direct responsibility of Subcommittee E07.01 on Radiology (X and
Gamma) Method.
Current edition approved June 1, 2015June 1, 2022. Published June 2015June 2022. Originally approved in 2001. Last previous edition approved in 20092015 as
E2104 - 09.E2104 – 15. DOI: 10.1520/E2104-15.10.1520/E2104-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E2104 − 22
E1165 Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging
E1254 Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
E1316 Terminology for Nondestructive Examinations
E1390 Specification for Illuminators Used for Viewing Industrial Radiographs
E1316 Terminology for Nondestructive Examinations
E1815 Test Method for Classification of Film Systems for Industrial Radiography
E1817 Practice for Controlling Quality of Radiological Examination by Using Representative Quality Indicators (RQIs)
E2033 Practice for Radiographic Examination Using Computed Radiography (Photostimulable Luminescence Method)
E2698 Practice for Radiographic Examination Using Digital Detector Arrays
3
2.2 AWS Documents:
ANSI/AWS A2.4 Symbols for Welding and Nondestructive Testing
4
2.3 AIA Documents:
NAS-410NAS410 Certification and Qualification of Nondestructive Test Personnel
5
2.4 NCRP Documents:
NCRP 51 Radiation Protection Design Guidelines for 0.1-100 MeV
...