iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F969-07

(Practice)

Standard Practice for Construction of Chain-Link Tennis Court Fence

Standard Practice for Construction of Chain-Link Tennis Court Fence

SIGNIFICANCE AND USE
The intended use of this practice is for 10- or 12-ft (3050 or 3660 mm) high chain-link fencing as complete enclosures around single or multiple tennis courts, or as backstops at either end of tennis courts.  
This practice is not intended for applications where fencing higher than 12 ft (3660 mm) is desired for a special application.  
Caution Regarding Windscreens— If wind screens are to be installed at the time of fence erection or at a later time, it is advisable to use stronger framework and parts and closer spacing of posts or back bracing depending upon the type of screening material to be used, area of fence to be covered, and local wind conditions. The Chain Link Fence Manufacturers Institute’s (CLFMI), Guide WLG 2445, provides the designer with the process to select the post size and post spacing.
SCOPE
1.1 This practice covers fencing around tennis courts, built from various types of chain-link fabric and framework materials, and installation practices for same.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jan-2007
ICS
97.220.10 - Sports facilities
Technical Committee
F14 - Fences
Drafting Committee
F14.10 - Specific Applications and Other Fence Systems and Components
Current Stage
Ref Project

Relations

Replaces
ASTM F969-01 - Standard Practice for Construction of Chain-Link Tennis Court Fence
Effective Date
01-Feb-2007
Replaced By
ASTM F969-11 - Standard Practice for Construction of Chain-Link Tennis Court Fence
Effective Date
01-Jun-2011
Referred By
ASTM F1553-11(2022) - Standard Guide for Specifying Chain Link Fence
Effective Date
01-Feb-2007

Buy Standard

ASTM F969-07 - Standard Practice for Construction of Chain-Link Tennis Court FenceASTM F969-07 - Standard Practice for Construction of Chain-Link Tennis Court Fence
PreviousNext
Standard
ASTM F969-07 - Standard Practice for Construction of Chain-Link Tennis Court Fence
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F969–07
Standard Practice for
1
Construction of Chain-Link Tennis Court Fence
ThisstandardisissuedunderthefixeddesignationF969;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Wire Used with Chain-Link Fence
2.2 Other Standards:
1.1 This practice covers fencing around tennis courts, built
WLG 2445 Guide for the Selection of Line Posts and their
from various types of chain-link fabric and framework mate-
3
Spacing
rials, and installation practices for same.
1.2 This standard does not purport to address all of the
3. Terminology
safety concerns, if any, associated with its use. It is the
3.1 Definitions—See Definitions F552 for definitions of
responsibility of the user of this standard to establish appro-
terms used in this practice.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
4. Summary of Practice
2. Referenced Documents 4.1 This practice is intended primarily to guide those
2 responsible for or concerned with the design and installation of
2.1 ASTM Standards:
chain-link fencing around tennis courts.
A392 Specification for Zinc-Coated Steel Chain-Link
4.2 This practice does not intend to preclude any practice
Fence Fabric
that has proven equal to or given better performance under
A491 Specification forAluminum-Coated Steel Chain-Link
varying conditions such as location, weather, intended use, etc.
Fence Fabric
A824 Specification for Metallic-Coated Steel Marcelled
5. Significance and Use
Tension Wire for Use With Chain Link Fence
5.1 Theintendeduseofthispracticeisfor10-or12-ft(3050
F552 Terminology Relating to Chain Link Fencing
or 3660 mm) high chain-link fencing as complete enclosures
F567 Practice for Installation of Chain-Link Fence
around single or multiple tennis courts, or as backstops at
F626 Specification for Fence Fittings
either end of tennis courts.
F668 Specification for Polyvinyl Chloride (PVC) and Other
5.2 This practice is not intended for applications where
Organic Polymer-Coated Steel Chain-Link Fence Fabric
fencing higher than 12 ft (3660 mm) is desired for a special
F900 Specification for Industrial and Commercial Swing
application.
Gates
5.3 Caution Regarding Windscreens— If wind screens are
F934 Specification for Colors for Polymer-Coated Chain
to be installed at the time of fence erection or at a later time, it
Link Fence Materials
is advisable to use stronger framework and parts and closer
F1043 Specification for Strength and Protective Coatings
spacing of posts or back bracing depending upon the type of
on Steel Industrial Chain Link Fence Framework
screening material to be used, area of fence to be covered, and
F1083 Specification for Pipe, Steel, Hot-Dipped Zinc-
local wind conditions. The Chain Link Fence Manufacturers
Coated (Galvanized) Welded, for Fence Structures
Institute’s (CLFMI), Guide WLG 2445, provides the designer
F1345 Specification for Zinc-5 % Aluminum-Mischmetal
with the process to select the post size and post spacing.
Alloy-Coated Steel Chain-Link Fence Fabric
F1664 Specification for Poly(Vinyl Chloride) (PVC) and
6. Classification
Other Conforming Organic Polymer-Coated Steel Tension
6.1 The four types of chain-link fencing described in this
practice are classified as follows:
6.1.1 Type I—Built with aluminum-coated steel chain-link
1
This practice is under the jurisdiction ofASTM Committee F14 on Fences and
fence fabric as specified in Specification A491.
is the direct responsibility of Subcommittee F14.10 on Specific Applications.
6.1.2 Type II—Built with zinc-coated steel chain-link fence
Current edition approved Feb. 1, 2007. Published February 2007. Originally
fabric as specified in SpecificationA392, Class 1 coating only.
approved in 1986. Last previous edition approved in 2001 as F969 - 01. DOI:
10.1520/F0969-07.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on AvailablefromChainLinkFenceManufacturersInstitute,10015OldColumbia
the ASTM website. Road, Suite B-215, Columbia, MD 21046, http://www.chainlinkinfo.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F969–07
6.1.3 Type III—Built with zinc-5% aluminum-mischmetal 8.3 Horizontal Rails:
alloy-coated steel chain-link fence fabric as specified in Speci- 8.3.1 Horizontal rails shall be as selected from Specifica-
fication F1345, in a choice of C
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3558-22(Guide)
Standard Guide for Chain-Link Pickleball Court Fences

SIGNIFICANCE AND USE
5.1 The Intended Use of This Guide is to identify the specific functions and qualities desired of a pickleball fence and offer recommendations on how to achieve them with a chain link fence for different types of pickleball courts.  
5.2 The Primary Function of a Pickleball Court Fence is to keep pickleball balls in and uninvited traffic out. It also serves as a barrier to prevent players from colliding with fixed objects and spectators. It also prevents players from running onto irregular or slippery surfaces or into dangerous adjacent areas. Fences need to respond to secondary functional requirements, including: spectator viewing, screening the court from wind and visual distractions outside the court, and being as open and welcoming as security conditions permit. In cases where security or dangerous adjacent conditions are an issue, a uniformly high type of enclosure can still be called for, but in most cases, pickleball fences are a variety of heights and may accommodate lights, shade shelters, gates for players and maintenance, and can have completely open (no fence) portions of the perimeter that lead to decks, grandstands, or landscaping
SCOPE
1.1 The purpose of this guide is to inform the builder, designer, facility manager, or owner, or a combination thereof, of a pickleball court or facility about the many details and features of pickleball court fence. It focuses on what to consider when designing a pickleball fence, offers some recommendations, and points the user to where they could find additional useful information regarding the design, construction, and maintenance of pickleball courts.  
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2000-19(Specification)
Standard Safety Performance Specification for Fences for Baseball and Softball Fields

SCOPE
1.1 This specification provides recommended minimum requirements for various types of fences used in softball and baseball ballfields and other sports facilities, and practices for installation.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2698-08(2018)(Guide)
Standard Guide for Fences for Above-Ground and In-ground Skate Park Facilities

SIGNIFICANCE AND USE
5.1 This guide sets forth minimum standard requirements for use in local codes and ordinances relating to fences/barriers separating pedestrian circulation and traffic areas from skate park and related venue enclosures to prevent collision, contain the skateboards and prevent falls into such in-ground venue areas.  
5.2 This guide sets forth minimum standard requirements for use in local codes and ordinances relating to enclosing skate parks and preventing unfamiliar use of the facilities creating falls from hazards.  
5.3 This guide does not have the effect of law, nor is it intended to supersede local codes and ordinances of a more restrictive nature.  
5.4 Studies have been the basis for certain recommendations in this guide and will assist those who intend to provide protection against unfamiliar access by restricting access to children under the age of five years who have no training and others unfamiliar with the equipment and features in skateboards. This would include, but is not limited to, state and local governments, model code organizations, building code groups, and consumers. It is understood that the format will vary depending upon the specific use and local conditions.
SCOPE
1.1 This guide provides recommended minimum requirements for denoting the various types of fences/barriers for skate parks and for inline skating or roller hockey rinks and extreme performance areas.  
1.2 This guide provides the minimum requirements for the protection of the participants from intrusion of other activity users; from unauthorized and unsupervised use by users that could be harmed by unanticipated entry into the area and from falls into in-ground skate park area.  
1.3 This guide provides for the safety of spectators from errant skateboard use.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are provided for information purposes only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2699-08(2018)(Guide)
Standard Guide for Fences for Commercial and Public Outdoor Water Spray/Play Areas

SIGNIFICANCE AND USE
5.1 This guide sets forth minimum standard requirements for use in local codes and ordinances relating to commercial and public water spray/play areas.  
5.2 This guide does not have the effect of law, nor is it intended to supersede local codes and ordinances of a more restrictive nature.  
5.3 This guide provides certain recommendations to assist those who intend to provide protection against injuries or fatalities associated with any possible vehicle passage into, or pedestrian passage to or from a water spray/play area environment by children. This would include, but not be limited to, state and local governments, model code organizations, building code groups, and consumers. It is understood that the format will vary depending upon the specific use and local conditions.
SCOPE
1.1 This guide provides the recommended minimum requirements for various types of fences for commercial and public outdoor water spray/play areas.  
1.2 This guide provides for the safety of occupants in water spray/play areas or zones as it pertains to vehicular intrusion as well as other participant intrusion, and for children containment or entry/exit.  
1.3 This guide does not choose the product components for the fence system, the choice of which should be made by the operators of the water spray/play area space and their specification writers or drafters based upon their determination of the merits of the products that could be used.  
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values stated in parentheses are provided for information purposes only.  
1.5 This guide does not purport to address the aspect of safety within a water spray/play area or zone. It is the responsibility of the user of this guide to establish appropriate safety practices as related to the water spray/play area and determine the applicability of regulatory requirements prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F969-11(2016)(Practice)
Standard Practice for Construction of Chain-Link Tennis Court Fence

SIGNIFICANCE AND USE
5.1 The intended use of this practice is for 10- or 12-ft (3050 or 3660 mm) high chain-link fencing as complete enclosures around single or multiple tennis courts, or as backstops at either end of tennis courts.  
5.2 This practice is not intended for applications where fencing higher than 12 ft (3660 mm) is desired for a special application.  
5.3 Caution Regarding Windscreens—If wind screens are to be installed at the time of fence erection or at a later time, it is advisable to use stronger framework and parts and closer spacing of posts or back bracing depending upon the type of screening material to be used, area of fence to be covered, and local wind conditions. The Chain Link Fence Manufacturers Institute’s (CLFMI), Guide WLG 2445, provides the designer with the process to select the post size and post spacing.
SCOPE
1.1 This practice covers fencing around tennis courts, built from various types of chain-link fabric and framework materials, and installation practices for same.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1346-23(Specification)
Standard Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs

SCOPE
1.1 This specification establishes requirements for safety covers for swimming pools, spas, hot tubs, and wading pools (hereinafter referred to as pools, unless otherwise specified). When correctly installed and used in accordance with the manufacturer's instructions, this specification is intended to reduce the risk of drowning by inhibiting the access of children under five years of age to the water.  
1.2 This specification includes performance tests to demonstrate the compliance or noncompliance to requirements herein stated for safety covers. It also includes marking requirements for all covers.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods section, Section 9, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2959-23a(Practice)
Standard Practice for Aerial Adventure Courses

SIGNIFICANCE AND USE
4.1 The rational for developing a separate standard practice for Aerial Adventure Courses is based on the unique functional, operational and patron participation requirements when compared to amusement rides and devices.  
4.2 The purpose of this practice is to provide designers, manufacturers, constructors, system integrators, owners/operators, and auditors with criteria and references for use in the design, manufacture, construction, installation, integration, operation, maintenance, auditing, and major modification of Aerial Adventure Courses.  
4.3 Unless this practice expressly provides otherwise in a particular provision, the term “Aerial Adventure Course” is to be used in place of “Amusement Rides and Devices” herein.
SCOPE
1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Auditing and Major Modification of Aerial Adventure Courses.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    28 pages
    English language
    sale 15% off
  • Standard
    28 pages
    English language
    sale 15% off
ASTM
ASTM F2461-23(Practice)
Standard Practice for Manufacture, Construction, Operation, and Maintenance of Aquatic Play Equipment

SCOPE
1.1 This practice covers information for manufacture, construction, operations and maintenance of aquatic play equipment and provides safety performance standards for various types of public aquatic play components and aquatic play composite structures.  
1.2 Inclusions:  
1.2.1 Climbable and climb-resistant aquatic play components, composite aquatic play structures, user controls, water sprays, fountains, and slides that occur on wet decks and wading, swimming or leisure pools. The play components specified herein occur for use in aquatic play areas.  
1.2.2 Play equipment, fall zones, use zones for wet decks, wading pools, swimming pools and leisure pools.  
1.2.3 This standard is intended to apply to Aquatic Play Equipment that is located in and around re- circulated and potable water recreational facilities. Such facilities include but are not limited to amusement parks, theme parks, water parks, family entertainment centers, municipal swimming pools and municipal parks.  
1.2.4 Waterslides 6 ft in height or smaller.  
1.3 Exclusions:  
1.3.1 Playground equipment that does not have an entry or an exit onto or into a wet deck, wading pool, swimming pool or aquatic recreation pool.  
1.3.2 Home playground or home pool equipment or play equipment as scoped in Consumer Safety Performance Specification F1148-21 and ANSI/NSPI-5.  
1.3.3 Waterslides as scoped in Practice F2376-22.  
1.3.4 Flotation devices used on water slides or in swimming pools.  
1.3.5 Swimming pools as specified by ANSI/NSPI-1 or ANSI/IAF-9.  
1.3.6 Products or facility elements specifically designed to provide access to and from pools for people with disabilities.  
1.3.7 Water rides such as log flumes, raft rides, inner tube rides, waterslides or other attractions where the participant sits in a vehicle or is physically propelled or moved by or with water.  
1.3.8 Sports equipment, fitness equipment, and diving equipment.  
1.4 Compliance:  
1.4.1 Where water is indirectly or directly added or applied to Consumer Safety Performance Specification F1487-21 play equipment, the equipment shall comply with this standard. Where a requirement for compliance to a section of the Consumer Safety Performance Specification F1487-21 standard is required by this standard, the section number is preceded with the standard's designation.  
1.4.2 Soft contained play structures with aquatic play components shall comply with Safety Performance Specification F1918-21 except as modified by this standard.  
1.4.3 Aquatic play components and composite play structures represented, as complying with this safety performance standard shall meet all applicable requirements specified herein. Anyone representing compliance with this standard shall keep such essential records as are necessary to document any claim that the requirements within this standard have been met.  
1.5 This standard includes the following sections:    
Scope  
Section 1  
Referenced Documents  
Section 2  
Terminology  
Section 3  
Manufacturing and Materials  
Section 4  
Design  
Section 5  
Performance Requirements  
Section 6  
Operator Responsibilities  
Section 7  
Manufacturer/Designer
Responsibilities  
Section 8  
Installer Responsibilities  
Section 9  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. (The conversion factor from inch-pound to metric units is 1 in. = 25.4 mm, and 1 lb = 4.4482 N.)  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with intern...

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM F1777-19(2023)(Practice)
Standard Practice for Paintball Game Site Operation

ABSTRACT
This practice sets forth procedures for operating a paintball playing field. The goal is to assist paintball field operators in running a safe business. Like any other physical activity, paintball presents a potential for injury. No procedural practice can prevent all injuries, especially when paintball players do not follow safety instructions. The ultimate responsibility for preventing injury lies with the paintball player. This practice, however, intends to promote safe paintball field operation through standardization of operating practice.
SCOPE
1.1 This practice establishes minimum safety requirements for the operation of paintball playing game sites, and provides for certain materials and procedures required.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2286-16(2023)(Specification)
Standard Design and Performance Specification for Removable Mesh Fencing for Swimming Pools, Hot Tubs, and Spas

SCOPE
1.1 This specification outlines the performance and design requirements for removable mesh safety barriers used for barriers for swimming pools, hot tubs, and spas to reduce the incidence of injuries or death for infants and children up to and including five years of age.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off