ASTM D2467-04

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 2467 – 04
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
1
80
This standard is issued under the fixed designation D 2467; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2. Referenced Documents
2
1.1 This specification covers poly(vinyl chloride) (PVC) 2.1 ASTM Standards:
Schedule 80 pipe fittings. Included are requirements for mate- D 618 Practice for Conditioning Plastics for Testing
rials, workmanship, dimensions, and burst pressure. D 1599 Test Method for Resistance to Short-Time Hydrau-
lic Pressure of Plastic Pipe, Tubing, and Fittings
NOTE 1—CPVC plastic pipe fittings, which were formerly included in
D 1600 Terminology for Abbreviated Terms Relating to
this standard, are now covered in Specification F 439.
Plastics
1.2 The products covered by this specification are intended
D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
for use with the distribution of pressurized liquids only, which
Compounds and Chlorinated Poly(Vinyl Chloride)
are chemically compatible with the piping materials. Due to
(CPVC) Compounds
inherent hazards associated with testing components and sys-
D 1785 Specification for Poly(Vinyl Chloride) (PVC) Plas-
tems with compressed air or other compressed gases, some
tic Pipe, Schedules 40, 80, and 120
manufacturers do not allow pneumatic testing of their products.
D 2122 Test Method for Determining Dimensions of Ther-
Consult with specific product/component manufacturers for
moplastic Pipe and Fittings
their specific testing procedures prior to pneumatic testing.
D 2749 Symbols for Dimensions of Plastic Pipe Fittings
F 412 Terminology Relating to Plastic Piping Systems
NOTE 2—Pressurized (compressed) air or other compressed gases
contain large amounts of stored energy, which present serious safety
F 439 Specification for Chlorinated Poly (Vinyl Chloride)
hazards should a system fail for any reason.
(CPVC) Plastic Pipe Fittings, Schedule 80
F 1498 Specification for Taper Pipe Threads 60° for Ther-
1.3 The text of this specification references notes, footnotes,
moplastic Pipe and Fittings
and appendixes which provide explanatory material. These
3
2.2 Federal Standard:
notes and footnotes (excluding those in tables and figures) shall
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
not be considered as requirements of this specification.
4
2.3 National Sanitation Foundation Standards:
1.4 The values stated in inch-pound units are to be regarded
Standard No. 14 for Plastic Piping Components and Related
as the standard. The values given in parentheses are provided
Materials
for information only.
Standard No. 61 for Drinking Water Systems
1.5 The following safety hazards caveat pertains only to the
Components—Health Effects
test method portion, Section 8, of this specification. This
standard does not purport to address all of the safety concerns,
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health
practices and determine the applicability of regulatory limita-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
tions prior to use.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
1 3
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
4
Current edition approved April 1, 2004. Published May 2004. Originally Available from the National Sanitation Foundation, P.O. Box 1468, Ann Arbor,
approved in 1965. Last previous edition approved in 2002 as D 2467 – 02. MI 48106.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 2467 – 04
3. Terminology 6.2 Threads—For all fittings having taper pipe threads,
threads shall conform to Specification F 1498 and be gaged in
3.1 General—Definitions are in accordance with Terminol-
accordance with 8.4.
ogy F 412 and abbreviations are in accordance with Terminol-
6.3 Burst Pressure:
ogy D 1600, unless otherwise indicated. The abbreviation for
6.4 Fittings tested in accordance with 8.5 shall withstand the
poly
...