ASTM D600-07

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D600 −07
StandardSpecification for
1
Liquid Paint Driers
This standard is issued under the fixed designation D600; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* D1545 Test Method for Viscosity of Transparent Liquids by
Bubble Time Method
1.1 This specification covers liquids for use in paints,
E29 Practice for Using Significant Digits in Test Data to
varnishes, enamels, and similar organic coatings and are
Determine Conformance with Specifications
solutions of metallic salts of:
2.2 U.S. Federal Specification:
1.1.1 Class A—2-Ethyl hexanoic acids in petroleum spirits.
PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging
1.1.2 Class B—Naphthenic acids in petroleum spirits.
3
of
1.1.3 Class C—Neodecanoic acids in petroleum spirits.
1.1.4 Class D—Tall oil fatty acids in petroleum spirits.
3. Chemical and Physical Requirements
1.1.5 Class E—Any of the above acids or acid blends, but
3.1 Quantitative Requirements—The drier shall conform to
containing additives that make the liquid drier water dispers-
the quantitative requirements as specified in Table 1 for
ible. Some other driers may also contain complexing agents.
metallic content, color, and viscosity.
1.1.6 Class F—Other acids and acid blends unidentified by
their producers. 3.2 Physical Appearance—Each type of drier shall be a
mobile liquid free of sediment and suspended matter and shall
1.2 The following applies to all specified limits in this
be stable and miscible with oil as listed in Test Methods D564.
standard; for purposes of determining conformance with this
standard, an observed value or a calculated value shall be
4. Significance and Use
rounded off “to the nearest unit” in the last right-hand digit
4.1 This specification covers the general requirements for
used in expressing the specification limit in accordance with
liquid paint driers used in paints, varnishes, enamels, and
the rounding-off method of Practice E29.
similar organic coatings.
1.3 The values stated in SI units are to be regarded as
4.2 The values listed should be considered as general guides
standard. No other units of measurement are included in this
to the character of the products, rather than reproducible
standard.
constants.
1.4 For specific hazard information and guidance, see the
supplier’s Material Safety Data Sheets for materials listed in
5. Test Methods
this specification.
5.1 The properties enumerated in this specification shall be
determined in accordance with Test Methods D564, except as
2. Referenced Documents
otherwise provided in this specification.
2
2.1 ASTM Standards:
D564 Test Methods for Liquid Paint Driers
D1544 Test Method for Color of Transparent Liquids (Gard-
ner Color Scale)
1
This specification is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, andApplications and is the direct responsibility of
Subcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.
CurrenteditionapprovedJune1,2007.PublishedJuly2007.Originallyapproved
in 1941. Last previous edition approved in 2001 as D600 – 90 (2001). DOI:
10.1520/D0600-07.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. www.dodssp.daps.mil.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D600−07
A
TABLE 1 Typical Requirements of Liquid Paint Driers
Nonvolative Typical Specific B
Color, Gardner
Metal Concentration, %
G-H Viscosity (Test
Matter, % Gravity 25/25°C
Class Metal (Test Method
Method D1545)
D1544)
min max max min max
C
A Calcium 3.9 4.1 50 0.884 —3 A
A Calcium 4.9 5.1 60 0.894 0.912 5 C
B Calcium 3.9 4.1 70 0.902 0.937 10 D
B Calcium 4.9 5.1 85 0.932 0.970 11 T
C Calcium 4.9 5.1 46 0.888 — 2 A
D Calcium 3.9 4.1 66 0.890 0.918 9 B
E Calcium 3.9 4.1 63 0.905 0.930 8 G
E Calcium 5.9 6.1 76 0.922 0.960 5 N
F Calcium 3.9 4.1 50 0.850 0.884 3 A
F Calcium 4.9 5.1 60 0.900 0.936 4 B
F Calcium 5.9 6.1 74 0.873 0.948 6 N
F Calcium 7.9 8.1 70 0.958 — 5 B
F Calcium 9.9 10.1 65 1.000 1.030 7–8 K
A Cerium 5.9 6.1 30 0.856 — 8 A
B Cerium 5.9 6.1
...