ASTM C109/C109M-08

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:C109/C109M–07 Designation: C 109/C 109M – 08
Standard Test Method for
Compressive Strength of Hydraulic Cement Mortars (Using
1
2-in. or [50-mm] Cube Specimens)
This standard is issued under the fixed designation C 109/C 109M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—A typo in 5.9.2 was corrected editorially August 2008.
1. Scope*
1.1 Thistestmethodcoversdeterminationofthecompressivestrengthofhydrauliccementmortars,using2-in.or[50-mm]cube
specimens.
NOTE 1—Test Method C 349 provides an alternative procedure for this determination (not to be used for acceptance tests).
1.2 This test method covers the application of the test using either inch-pound or SI units. The values stated in either system
shall SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets.
The values stated in each system aremay not be exact equivalents; therefore, each system shall be used independently of the other.
Combining values from the two systems may result in nonconformance with the specification. standard.
1.3 ValuesinSIunitsshallbeobtainedbymeasurementinSIunitsorbyappropriateconversion,usingtheRulesforConversion
and Rounding given in Standard IEEE/ASTM SI 10, of measurements made in other units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and
2
tissue upon prolonged exposure. )
2. Referenced Documents
3
2.1 ASTM Standards:
C91 Specification for Masonry Cement
C114 Test Methods for Chemical Analysis of Hydraulic Cement
C 150 Specification for Portland Cement
C 230/C 230M Specification for Flow Table for Use in Tests of Hydraulic Cement
C 305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
C 349 Test Method for Compressive Strength of Hydraulic-Cement Mortars (Using Portions of Prisms Broken in Flexure)
C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of
Hydraulic Cements and Concretes
C 595 Specification for Blended Hydraulic Cements
C 618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C 670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
C 778 Specification for Standard Sand
C 989 Specification for Slag Cement for Use in Concrete and Mortars
C 1005 Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of
Hydraulic Cements
C 1157 Performance Specification for Hydraulic Cement
C 1328 Specification for Plastic (Stucco) Cement
C 1329 Specification for Mortar Cement
1
This test method is under the jurisdiction of ASTM Committee C01 on Cement and is the direct responsibility of Subcommittee C01.27 on Strength.
Current edition approved Aug. 15, 2007. Published September 2007. Originally approved in 1934. Last previous edition approved in 2005 as C 109/C109M–05.
´1
Current edition approved Dec. 1, 2008. Published January 2009. Originally approved in 1934. Last previous edition approved in 2007 as C 109/C 109M – 07 .
2
See the section on Safety, Manual of Cement Testing, Annual Book of ASTM Standards, Vol 04.01.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C 109/C 109M – 08
C 1437 Test Method for Flow of Hydraulic Cement Mortar
IEEE/ASTM SI 10 Standard for Use of the International System of Units (SI): The Modern Metric System
3. Summary of Test Method
3.1 The mortar used consis
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:C109/C109M–07 Designation: C 109/C 109M – 08
Standard Test Method for
Compressive Strength of Hydraulic Cement Mortars (Using
1
2-in. or [50-mm] Cube Specimens)
This standard is issued under the fixed designation C 109/C 109M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
´ NOTE—A typo in 5.9.2 was corrected editorially August 2008.
1. Scope*
1.1 Thistestmethodcoversdeterminationofthecompressivestrengthofhydrauliccementmortars,using2-in.or[50-mm]cube
specimens.
NOTE 1—Test Method C 349 provides an alternative procedure for this determination (not to be used for acceptance tests).
1.2 This test method covers the application of the test using either inch-pound or SI units. The values stated in either system
shall SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets.
The values stated in each system aremay not be exact equivalents; therefore, each system shall be used independently of the other.
Combining values from the two systems may result in nonconformance with the specification. standard.
1.3 ValuesinSIunitsshallbeobtainedbymeasurementinSIunitsorbyappropriateconversion,usingtheRulesforConversion
and Rounding given in Standard IEEE/ASTM SI 10, of measurements made in other units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and
2
tissue upon prolonged exposure. )
2. Referenced Documents
3
2.1 ASTM Standards:
C91 Specification for Masonry Cement
C114 Test Methods for Chemical Analysis of Hydraulic Cement
C 150 Specification for Portland Cement
C 230/C 230M Specification for Flow Table for Use in Tests of Hydraulic Cement
C 305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
C 349 Test Method for Compressive Strength of Hydraulic-Cement Mortars (Using Portions of Prisms Broken in Flexure)
C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of
Hydraulic Cements and Concretes
C 595 Specification for Blended Hydraulic Cements
C 618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C 670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
C 778 Specification for Standard Sand
C 989 Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars
C 1005 Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of
Hydraulic Cements
C 1157 Performance Specification for Hydraulic Cement
C 1328 Specification for Plastic (Stucco) Cement
C 1329 Specification for Mortar Cement
1
This test method is under the jurisdiction of ASTM Committee C01 on Cement and is the direct responsibility of Subcommittee C01.27 on Strength.
Current edition approved Aug. 15, 2007. Published September 2007. Originally approved in 1934. Last previous edition approved in 2005 as C 109/C109M–05.
´1
Current edition approved Dec. 1, 2008. Published January 2009. Originally approved in 1934. Last previous edition approved in 2007 as C 109/C 109M – 07 .
2
See the section on Safety, Manual of Cement Testing, Annual Book of ASTM Standards, Vol 04.01.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C 109/C 109M – 08
C 1437 Test Method for Flow of Hydraulic Cement Mortar
IEEE/ASTM SI 10 Standard for Use of the International System of Units (SI): The Modern Metric System
3. Summary of Test Method
3
...