SIST EN ISO 20126:2005

SLOVENSKI STANDARD
SIST EN ISO 20126:2005
01-december-2005
=RER]GUDYVWYR5RþQH]REQHãþHWNH6SORãQH]DKWHYHLQSUHVNXVQHPHWRGH,62

Dentistry - Manual toothbrushes - General requirements and test methods (ISO
20126:2005)
Zahnheilkunde - Handzahnbürsten - Allgemeine Anforderungen und Prüfverfahren (ISO
20126:2005)
Art dentaire - Brosses a dents manuelles - Exigences générales et méthodes d'essai
(ISO 20126:2005)
Ta slovenski standard je istoveten z: EN ISO 20126:2005
ICS:
97.170 Oprema za nego telesa Body care equipment
SIST EN ISO 20126:2005 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 20126:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 20126:2005
EUROPEAN STANDARD
EN ISO 20126
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2005
ICS 97.170

English Version
Dentistry - Manual toothbrushes - General requirements and test
methods (ISO 20126:2005)
Art dentaire - Brosses à dents manuelles - Exigences Zahnheilkunde - Handzahnbürsten - Allgemeine
générales et méthodes d'essai (ISO 20126:2005) Anforderungen und Prüfverfahren (ISO 20126:2005)
This European Standard was approved by CEN on 4 September 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20126:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 20126:2005

EN ISO 20126:2005 (E)





Foreword


This document (EN ISO 20126:2005) has been prepared by Technical Committee ISO/TC 106
"Dentistry" in collaboration with Technical Committee CEN/TC 55 "Dentistry", the secretariat of
which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2006, and conflicting national
standards shall be withdrawn at the latest by March 2006.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 20126:2005 has been approved by CEN as EN ISO 20126:2005 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 20126:2005


INTERNATIONAL ISO
STANDARD 20126
First edition
2005-09-15


Dentistry — Manual toothbrushes —
General requirements and test methods
Art dentaire — Brosses à dents manuelles — Exigences générales et
méthodes d'essai




Reference number
ISO 20126:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 20126:2005
ISO 20126:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 20126:2005
ISO 20126:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 20126 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 7, Oral care
products.
This first edition of ISO 20126, together with ISO 22254, cancels and replaces ISO 8627:1987.
© ISO 2005 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 20126:2005
ISO 20126:2005(E)
Introduction
Manual toothbrushes are used for the removal of dental plaque and oral debris in order to facilitate oral
hygiene. This International Standard is intended for the physical properties of manual toothbrushes, but the
impact resistance is not included until such time that the test can be evaluated by the working group.

iv © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 20126:2005
INTERNATIONAL STANDARD ISO 20126:2005(E)

Dentistry — Manual toothbrushes — General requirements and
test methods
1 Scope
This International Standard specifies requirements and test methods for the physical properties of manual
toothbrushes in order to promote the safety of these products for their intended use.
Specifically excluded are manual interdental brushes and powered oral hygiene devices as these instruments
are covered by separate International Standards.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition ci
...