SIST EN 61300-3-27:1999

SLOVENSKI STANDARD
01-maj-1999
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 3-27: Examinations and measurements -
Measurement method for the hole location of a multiway connector plug (IEC
61300-3-27:1997)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures -- Part 3-27: Examinations and measurements - Measurement
method for the hole location of a multiway connector plug
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Meßverfahren -- Teil 3-27: Untersuchungen und Messungen - Meßmethode zur
Bestimmung der Lochposition eines Mehrfach-Stiftsteckverbinders
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d'essais et de mesures -- Partie 3-27: Examens et mesures - Méthode de
mesure pour la localisation du trou sur une fiche de connecteur multivoies
Ta slovenski standard je istoveten z: EN 61300-3-27:1997
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

NORME
CEI
INTERNATIONALE
IEC
61300-3-27
INTERNATIONAL
Première édition
STANDARD
First edition
1997-05
Dispositifs d’interconnexion et composants
passifs à fibres optiques – Méthodes
fondamentales d’essais et de mesures –
Partie 3-27:
Examens et mesures –
Méthode de mesure pour la localisation
du trou sur une fiche de connecteur multivoies
Fibre optic interconnecting devices
and passive components – Basic test
and measurement procedures –
Part 3-27:
Examinations and measurements –
Measurement method for the hole location
of a multiway connector plug
 IEC 1997 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni utilisée No part of this publication may be reproduced or utilized in
sous quelque forme que ce soit et par aucun procédé, électronique any form or by any means, electronic or mechanical, including
ou mécanique, y compris la photocopie et les microfilms, sans photocopying and microfilm, without permission in writing from
l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE F
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue

61300-3-27 © IEC:1997 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
–––––––––
FIBRE OPTIC INTERCONNECTING DEVICES AND
PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –
Part 3-27: Examinations and measurements – Measurement method
for the hole location of a multiway connector plug
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61300-3-27 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
The text of this standard is based on the following documents:
FDIS Report on voting
86B/849/FDIS 86B/958/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
IEC 61300 consists of the following parts, under the general title
Fibre optic interconnecting
devices and passive components – Basic test and measurement procedures:
– Part 1: General and guidance
– Part 2: Tests
– Part 3: Examinations a
...