SIST-TP R086-001:2004
(Main)Guidance for technology audit of fibre optic connector kits and terminated connectors
Guidance for technology audit of fibre optic connector kits and terminated connectors
CENELEC Report * D124/C047: Withdrawn
Guide pour les audites de filière technologique concernant les connecteurs pour fibre optique, en kit ou cablés
Navodila za tehnološko presojo konektorske opreme optičnih vlaken in zaključnih konektorjev*
General Information
Standards Content (Sample)
SLOVENSKI SIST-TP R086-001:2004
STANDARD
september 2004
Navodila za tehnološko presojo konektorske opreme optičnih vlaken in
zaključnih konektorjev*
Guidance for technology audit of fibre optic connector kits and terminated
connectors
ICS 33.180.
...
This May Also Interest You
EN IEC 61300-3-29 identifies two basic measurement methods for characterizing the spectral transfer functions of DWDM devices. The transfer functions are the functions of transmittance dependent of wavelengths. In this standard, optical attenuations are also used. The transfer functions can be used to produce measurements of insertion loss (IL), polarization dependent loss (PDL), isolation, centre wavelength, bandwidth (BW) and other optical performances.
- Standard42 pagesEnglish languagesale 10% offe-Library read for×1 day
EN IEC 61300-2-42 specifies a test to determine the influence of a side load applied to a cord assembled with a strain relief. The intention is to simulate a static load, due to a length of fibre cable, which would typically be experienced during service. Components should withstand side loads during optical transmission without degradation of the optical performance. Besides a boot, any feature that controls the bending radius of the fibre can be considered as strain relief.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which a fibre optical fuse satisfies in order to be categorised as meeting the requirements of single mode fibre plug-receptacle style optical fuse used in controlled environments. Optical performance specified in this document relate to plug-receptacle style configuration fuses only.
- Standard27 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61753 contains the minimum test and measurement requirements and severity levels that a passive chromatic dispersion compensator (PCDC) using virtually imaged phased array (VIPA) must satisfy in order to be categorized as meeting the IEC standard, category C-controlled environments. Generally, PCDCs are used to reduce the magnitude of chromatic dispersion (CD) between regenerators by adding CD to the span that has a sign opposite to the total CD of the fibre cable and components. The requirements cover non-connectorized PCDCs used in single-channel transmission and wavelength division multiplexing (WDM) transmission in single-mode fibres(IEC 60793-2-50 B1/B2/B4).
- Standard24 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61753 contains the minimum initial test and measurement requirements and severities which a fibre optical fuse satisfies in order for it to be categorised as meeting the requirements of single mode fibre pigtailed style optical fuse used in controlled environments. Optical performance specified in this document relates to in-line type configurations fuses only.
- Standard23 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61300 details a procedure for determining the suitability of a fibre optic device to withstand the environmental condition of high humidity and high temperature which may occur in actual use, storage and/or transport. The test is primarily intended to permit the observation of effects of high humidity at constant temperature over a given period. Absorption of moisture may result in swelling that would destroy functional utility, cause loss of physical strength, and cause changes in other important mechanical properties. Degradation of optical properties may also occur. Although not necessarily intended as a simulated tropical test, this test can, nevertheless, be useful in determining moisture absorption of insulating or covering materials.
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
The purpose of this part of IEC 61300 is to ensure that the captivation ort he attachment of the cable to the fibre optic device will withstand compressive axial loads likely to be applied during normal service.
- Standard10 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements that an SC-RJ connector set with one side protected by an industrial housing with the fibres terminated with cylindrical zirconia PC ferrules, an adaptor fitted with resilient alignment sleeves and
patchcord shall meet in order for it to be categorised as an EN standard product. The product is rated IP67. Since different variants are permitted, product marking details are given in 3.6.
- Corrigendum2 pagesGerman languagesale 10% offe-Library read for×1 day
This part of the IEC 61300 series, evaluates the assembly and reassembly of a fibre optic mechanical splice, a fibre management system or a closure for a specified number of times. The test procedures simulate the following conditions which may be encountered during the component's service lifetime: - the ability of an optical mechanical splice to be re-installed after disassembly; - the ability to re-enter fibre management systems and closures, by accessing fibres and optical components and making reconfigurations without disturbing transmission in adjacent fibre circuits; - verification of the sealing performance after frequent opening and closing of enclosures.
- Standard14 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 61754 defines the standard interface dimensions for the type SF optical board connector that uses a normal glass fibre and the physical contact technique to connect flexible optical boards and ribbon fibres.
- Standard16 pagesEnglish languagesale 10% offe-Library read for×1 day


Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.