SIST EN 303 039 V1.1.1:2014
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Multichannel transmitter specification for the PMR Service - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Multichannel transmitter specification for the PMR Service - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
The present document covers the technical requirements for multiple channel radio transmitters used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz. It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue speech and using constant envelope or non-constant envelope modulation. The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two or more RF channels. The types of equipment covered by the present document are as follows:
- base station (equipment fitted with an antenna connector, intended for use in a fixed location);
- mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
- those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter
output;
- and any equipment that may be used in combination with any of the above equipments when directly
connected to those equipments for the amplification of the transmitter output signals of two or more individual equipments. Types of equipment not covered by the present document are as follows:
- hand portable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document;
- any equipment using passive combining solutions where each transmitter connected to the passive combining system transmits on a single channel, as detailed in EG 200 053 [i.13], clause H.3. These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment, the receiver specifications in the relevant specification (references [i.5] to [i.12]) should apply. These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor do they necessarily represent the optimum performance achievable. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.3] (R&TTE Directive), which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.3] may apply to equipment within the scope of the present document.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Storitev kopenskih mobilnih komunikacij - Specifikacija večkanalnega oddajnika za storitev PMR - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Ta dokument zajema tehnične zahteve za radijske oddajnike in sprejemnike, ki se uporabljajo v postajah za storitev zasebnega mobilnega radia (PMR). Uporablja se za storitev kopenskih mobilnih komunikacij, ki deluje na radijskih frekvencah med 30 MHz in 3 GHz ter ima medkanalske razmike < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz in 150 kHz.Uporablja se za opremo za neprekinjen in/ali prekinjen prenos podatkov in/ali digitalen prenos govora in/ali analogen prenos govora, ki uporablja modulacijo s konstantno ali nekonstantno ovojnico. Opremo sestavlja oddajnik, ki omogoča simultano ojačanje ali oddajanje na dveh radiofrekvenčnih kanalih ali več, ali ojačevalnik, ki pri uporabi z opremo za oddajanje omogoča hkraten prenos na dveh radiofrekvenčnih kanalih ali več. Ta dokument zajema naslednje vrste opreme:
– bazna postaja (oprema z antenskim priključkom za uporabo na stalni lokaciji);
– mobilna postaja (oprema z antenskim priključkom, ki se običajno uporablja v vozilu ali prenosno);
– prenosne postaje:
a) z antenskim priključkom; ali
b) brez zunanjega antenskega priključka (vgrajene antene), vendar opremljene s stalnim ali začasnim notranjim 50-ohmskim radiofrekvenčnim konektorjem, ki omogoča dostop do izhoda
oddajnika;
– in vsaka oprema, ki se jo lahko uporablja v kombinaciji z zgoraj navedeno opremo, ko je neposredno
povezana z opremo za ojačanje izhodnih signalov oddajnika dveh posameznih naprav ali več. Vrste opreme, ki jih ta dokument ne zajema:
– prenosna oprema brez zunanjega ali notranjega radijskofrekvenčnega priključka in brez možnosti namestitve začasnega notranjega 50-ohmskega priključka;
– oprema, ki uporablja pasivne kombinirane rešitve, pri katerih vsak oddajnik, povezan s pasivnim kombiniranim sistemom, oddaja na enem samem kanalu, kot je to opisano v točki H.3 standarda EG 200 053 [i.13]. Te specifikacije veljajo samo za oddajnik ali ojačevalnik oddajnika. Če je sprejemnik priključen na isto opremo, se uporabljajo specifikacije za sprejemnik iz ustrezne specifikacije (reference [I.5] do [I.12]). Te specifikacije ne vključujejo nujno vseh lastnosti, ki bi jih lahko potreboval uporabnik opreme, niti ne predstavljajo nujno optimalnega delovanja. Ta dokument zajema določila člena 3.2 Direktive 1999/5/ES [i.3] (direktive R&TTE), ki navaja, da »... mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.«
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE [i.3].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.577(Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Multichannel transmitter specification for the PMR Service - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 303 039 Version 1.1.1SIST EN 303 039 V1.1.1:2014en01-maj-2014SIST EN 303 039 V1.1.1:2014SLOVENSKI
STANDARD
SIST EN 303 039 V1.1.1:2014
ETSI EN 303 039 V1.1.1 (2014-04) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Multichannel transmitter specification for the PMR Service; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Harmonized European Standard SIST EN 303 039 V1.1.1:2014
ETSI ETSI EN 303 039 V1.1.1 (2014-04) 2
Reference DEN/ERM-TGDMR-314 Keywords data, mobile, PMR, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 303 039 V1.1.1:2014
ETSI ETSI EN 303 039 V1.1.1 (2014-04) 3 Contents Intellectual Property Rights . 5 Foreword . 5 Introduction . 5 1 Scope . 6 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 7 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 9 3.3 Abbreviations . 10 4 General . 11 4.1 Presentation of equipment for testing purposes . 11 4.1.1 Choice of model for testing . 11 4.1.1.1 Auxiliary test equipment . 11 4.1.1.2 Declarations by the provider . 11 4.2 Multi-Mode equipment . 12 4.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 12 5 Test conditions, power sources and ambient temperatures . 12 5.1 Normal and extreme test conditions . 12 5.2 Test power source . 12 5.3 Normal test conditions . 12 5.3.1 Normal temperature and humidity . 12 5.3.2 Normal test power source . 13 5.3.2.1 Mains voltage . 13 5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13 5.3.2.3 Other power sources . 13 5.4 Extreme test conditions . 13 5.4.1 Extreme temperatures . 13 5.4.2 Extreme test source voltages . 13 5.4.2.1 Mains voltage . 13 5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 13 5.4.2.3 Power sources using other types of batteries . 14 5.4.2.4 Other power sources . 14 5.5 Procedure for tests at extreme temperatures . 14 5.5.1 Procedure for equipment designed for continuous transmission. 14 5.5.2 Procedure for equipment designed for intermittent transmission . 14 6 General test conditions . 15 6.1 Test bandwidth . 15 6.2 Test load (artificial antenna) . 15 6.3 Test signals (wanted and unwanted signals) . 15 6.3.1 Transmitter test signals for digital transmissions . 15 6.3.2 Encoder for digital transmitter measurements . 15 6.3.3 Transmitter test signals for analogue transmissions . 16 6.3.3.1 Test signals for frequency modulated channels. 16 6.3.3.2 Test signals for amplitude modulated channels. 16 6.3.3.3 Transmitter effective radiated power test signal (C1) . 16 6.4 Transceiver data interface for digital transmissions . 16 6.5 Impedance . 16 6.6 PEP . 16 6.7 Duplex equipment . 17 6.8 Modes of operation of the transmitter . 17 6.9 Measurement filter definition for digital transmissions . 17 SIST EN 303 039 V1.1.1:2014
ETSI ETSI EN 303 039 V1.1.1 (2014-04) 4 7 Technical characteristics of the transmitter . 17 7.1 Transmitter output power (conducted) . 17 7.1.1 Definitions . 17 7.1.2 Method of measurement . 18 7.1.3 Limits . 18 7.2 Adjacent and alternate channel power . 18 7.2.1 Definition . 18 7.2.2 Method of measurement . 19 7.2.3 Limits . 22 7.3 Unwanted emissions . 23 7.3.1 Definition . 23 7.3.2 Method of measuring the power level . 24 7.3.2.1 Measurement options . 24 7.3.2.2 Method of measuring conducted spurious emissions (clause 7.3.2.1 a)) . 24 7.3.2.3 Method of measuring the effective radiated power (clause 7.3.2.1 b)) . 25 7.3.2.4 Method of measuring wideband noise. 26 7.3.2.5 Method for measuring frequency conversion oscillator conducted spurious emissions. 27 7.3.2.6 Method for measuring third order intermodulation products between wanted channels . 28 7.3.3 Limits . 28 7.3.3.1 Spurious emissions power . 28 7.3.3.2 Wideband noise power . 29 7.3.3.3 Frequency conversion oscillator spurious emission . 30 7.3.3.4 Third order intermodulation product spurious emission . 30 7.4 Intermodulation attenuation. 31 7.4.1 Definition . 31 7.4.2 Method of measurement . 31 7.4.3 Limits . 32 7.5 Transient power measurements . 32 7.5.1 Definition . 32 7.5.2 Method of Measurement . 32 7.5.3 Limits . 33 8 Measurement uncertainty . 33 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 35 Annex B (normative): Radiated measurement . 37 B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 37 B.1.1 Anechoic chamber . 37 B.1.2 Anechoic chamber with a conductive ground plane . 38 B.1.3 Open Area Test Site (OATS) . 39 B.1.4 Test antenna . 40 B.1.5 Substitution antenna . 41 B.1.6 Measuring antenna . 41 B.2 Guidance on the use of radiation test sites . 41 B.2.1 Verification of the test site . 41 B.2.2 Preparation of the EUT . 41 B.2.3 Power supplies to the EUT . 41 B.2.4 Range length . 42 B.2.5 Site preparation . 42 B.3 Coupling of signals . 43 B.3.1 General . 43 B.3.2 Data signals . 43 Annex C (normative): Spectrum analyser specification . 44 Annex D (informative): Bibliography . 45 History . 46
SIST EN 303 039 V1.1.1:2014
ETSI ETSI EN 303 039 V1.1.1 (2014-04) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directive 98/34/EC [i.4] as amended by Directive 98/48/EC [i.14]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.3]. See article 5.1 of Directive 1999/5/EC for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.3] are summarized in annex A.
National transposition dates Date of adoption of this EN: 31 March 2014 Date of latest announcement of this EN (doa): 30 June 2014 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 December 2014 Date of withdrawal of any conflicting National Standard (dow): 31 December 2015
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.3]. The modular structure is shown in EG 201 399 [i.2]. SIST EN 303 039 V1.1.1:2014
ETSI ETSI EN 303 039 V1.1.1 (2014-04) 6 1 Scope The present document covers the technical requirements for multiple channel radio transmitters used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz. Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands Transmit
30 MHz to 3 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two or more RF channels. The types of equipment covered by the present document are as follows: • base station (equipment fitted with an antenna connector, intended for use in a fixed location); • mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable); • those hand portable stations: a) fitted with an antenna connector; or b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output; • and any equipment that may be used in combination with any of the above equipments when directly connected to those equipments for the amplification of the transmitter output signals of two or more individual equipments.
Types of equipment not covered by the present document are as follows: • hand portable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document; • any equipment using passive combining solutions where each transmitter connected to the passive combining system transmits on a single channel, as detailed in EG 200 053 [i.13], clause H.3. These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment, the receiver specifications in the relevant specification (references [i.5] to [i.12]) should apply. These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor do they necessarily represent the optimum performance achievable. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.3] (R&TTE Directive), which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.3] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. SIST EN 303 039 V1.1.1:2014
ETSI ETSI EN 303 039 V1.1.1 (2014-04) 7 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] Recommendation ITU-T O.153 (1992): "Basic parameters for the measurement of error performance at bit rates below the primary rate". [2] ETSI TR 100 028 (V1.4.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [3] ETSI TR 102 273 (V1.2.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties". [4] ANSI C63.5 (2004): "American National Standard for Electromagnetic Compatibility-Radiated Emission Measurements in Electromagnetic Interference (EMI) Control-Calibration of Antennas (9 kHz to 40 GHz)". 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] CEPT/ERC/REC 74-01 (2011): "Unwanted Emissions in the Spurious domain". [i.2] ETSI EG 201 399 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of candidate Harmonized Standards for application under the R&TTE Directive". [i.3] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [i.4] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. [i.5] ETSI EN 300 392-2: "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air Interface (AI)". [i.6] ETSI EN 302 561: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using constant or non-constant envelope modulation operating in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz or 150 kHz; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive". [i.7] ETSI EN 300 086: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment with an internal or external RF connector intended primarily for analogue speech". SIST EN 303 039 V1.1.1:2014
ETSI ETSI EN 303 039 V1.1.1 (2014-04) 8 [i.8] ETSI EN 300 113: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector". [i.9] ETSI EN 300 296: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech". [i.10] ETSI EN 300 341: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service (RP 02); Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver". [i.11] ETSI EN 300 390: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an integral antenna". [i.12] ETSI EN 301 166: "ElectroMagnetic Compatibility and Radio spectrum Matters (ERM); Land mobile service; Technical characteristics and test conditions for radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrowband channels and having an antenna connector". [i.13] ETSI EG 200 053: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio site engineering for radio equipment
...
ETSI EN 303 039 V1.1.1 (2014-04)
Harmonized European Standard
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Land Mobile Service; Multichannel transmitter
specification for the PMR Service;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 303 039 V1.1.1 (2014-04)
Reference
DEN/ERM-TGDMR-314
Keywords
data, mobile, PMR, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 039 V1.1.1 (2014-04)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 General . 11
4.1 Presentation of equipment for testing purposes . 11
4.1.1 Choice of model for testing . 11
4.1.1.1 Auxiliary test equipment . 11
4.1.1.2 Declarations by the provider . 11
4.2 Multi-Mode equipment . 12
4.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 12
5.3.1 Normal temperature and humidity . 12
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme test source voltages . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 14
5.5.1 Procedure for equipment designed for continuous transmission. 14
5.5.2 Procedure for equipment designed for intermittent transmission . 14
6 General test conditions . 15
6.1 Test bandwidth . 15
6.2 Test load (artificial antenna) . 15
6.3 Test signals (wanted and unwanted signals) . 15
6.3.1 Transmitter test signals for digital transmissions . 15
6.3.2 Encoder for digital transmitter measurements . 15
6.3.3 Transmitter test signals for analogue transmissions . 16
6.3.3.1 Test signals for frequency modulated channels. 16
6.3.3.2 Test signals for amplitude modulated channels. 16
6.3.3.3 Transmitter effective radiated power test signal (C1) . 16
6.4 Transceiver data interface for digital transmissions . 16
6.5 Impedance . 16
6.6 PEP . 16
6.7 Duplex equipment . 17
6.8 Modes of operation of the transmitter . 17
6.9 Measurement filter definition for digital transmissions . 17
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 039 V1.1.1 (2014-04)
7 Technical characteristics of the transmitter . 17
7.1 Transmitter output power (conducted) . 17
7.1.1 Definitions . 17
7.1.2 Method of measurement . 18
7.1.3 Limits . 18
7.2 Adjacent and alternate channel power . 18
7.2.1 Definition . 18
7.2.2 Method of measurement . 19
7.2.3 Limits . 22
7.3 Unwanted emissions . 23
7.3.1 Definition . 23
7.3.2 Method of measuring the power level . 24
7.3.2.1 Measurement options . 24
7.3.2.2 Method of measuring conducted spurious emissions (clause 7.3.2.1 a)) . 24
7.3.2.3 Method of measuring the effective radiated power (clause 7.3.2.1 b)) . 25
7.3.2.4 Method of measuring wideband noise. 26
7.3.2.5 Method for measuring frequency conversion oscillator conducted spurious emissions. 27
7.3.2.6 Method for measuring third order intermodulation products between wanted channels . 28
7.3.3 Limits . 28
7.3.3.1 Spurious emissions power . 28
7.3.3.2 Wideband noise power . 29
7.3.3.3 Frequency conversion oscillator spurious emission . 30
7.3.3.4 Third order intermodulation product spurious emission . 30
7.4 Intermodulation attenuation. 31
7.4.1 Definition . 31
7.4.2 Method of measurement . 31
7.4.3 Limits . 32
7.5 Transient power measurements . 32
7.5.1 Definition . 32
7.5.2 Method of Measurement . 32
7.5.3 Limits . 33
8 Measurement uncertainty . 33
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 35
Annex B (normative): Radiated measurement . 37
B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 37
B.1.1 Anechoic chamber . 37
B.1.2 Anechoic chamber with a conductive ground plane . 38
B.1.3 Open Area Test Site (OATS) . 39
B.1.4 Test antenna . 40
B.1.5 Substitution antenna . 41
B.1.6 Measuring antenna . 41
B.2 Guidance on the use of radiation test sites . 41
B.2.1 Verification of the test site . 41
B.2.2 Preparation of the EUT . 41
B.2.3 Power supplies to the EUT . 41
B.2.4 Range length . 42
B.2.5 Site preparation . 42
B.3 Coupling of signals . 43
B.3.1 General . 43
B.3.2 Data signals . 43
Annex C (normative): Spectrum analyser specification . 44
Annex D (informative): Bibliography . 45
History . 46
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 039 V1.1.1 (2014-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.4] as amended by Directive 98/48/EC [i.14].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.3].
See article 5.1 of Directive 1999/5/EC for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.3] are summarized in annex A.
National transposition dates
Date of adoption of this EN: 31 March 2014
Date of latest announcement of this EN (doa): 30 June 2014
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2014
Date of withdrawal of any conflicting National Standard (dow): 31 December 2015
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.3]. The
modular structure is shown in EG 201 399 [i.2].
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 039 V1.1.1 (2014-04)
1 Scope
The present document covers the technical requirements for multiple channel radio transmitters used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel
separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 3 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue
speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF
channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two
or more RF channels. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal
or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter
output;
• and any equipment that may be used in combination with any of the above equipments when directly
connected to those equipments for the amplification of the transmitter output signals of two or more individual
equipments.
Types of equipment not covered by the present document are as follows:
• hand portable equipment without an external or internal RF connector and without the possibility of having a
temporary internal 50 Ω RF connector is not covered by the present document;
• any equipment using passive combining solutions where each transmitter connected to the passive combining
system transmits on a single channel, as detailed in EG 200 053 [i.13], clause H.3.
These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment,
the receiver specifications in the relevant specification (references [i.5] to [i.12]) should apply.
These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor
do they necessarily represent the optimum performance achievable.
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.3] (R&TTE
Directive), which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated
to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.3] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 039 V1.1.1 (2014-04)
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.153 (1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
[2] ETSI TR 100 028 (V1.4.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[3] ETSI TR 102 273 (V1.2.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties".
[4] ANSI C63.5 (2004): "American National Standard for Electromagnetic Compatibility-Radiated
Emission Measurements in Electromagnetic Interference (EMI) Control-Calibration of Antennas
(9 kHz to 40 GHz)".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] CEPT/ERC/REC 74-01 (2011): "Unwanted Emissions in the Spurious domain".
[i.2] ETSI EG 201 399 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
A guide to the production of candidate Harmonized Standards for application under the R&TTE
Directive".
[i.3] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.4] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.5] ETSI EN 300 392-2: "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air
Interface (AI)".
[i.6] ETSI EN 302 561: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment using constant or non-constant envelope modulation operating
in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz or 150 kHz; Harmonized EN covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.7] ETSI EN 300 086: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment with an internal or external RF connector intended primarily for
analogue speech".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 303 039 V1.1.1 (2014-04)
[i.8] ETSI EN 300 113: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
mobile service; Radio equipment intended for the transmission of data (and/or speech) using
constant or non-constant envelope modulation and having an antenna connector".
[i.9] ETSI EN 300 296: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech".
[i.10] ETSI EN 300 341: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service (RP 02); Radio equipment using an integral antenna transmitting signals to initiate
a specific response in the receiver".
[i.11] ETSI EN 300 390: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an
integral antenna".
[i.12] ETSI EN 301 166: "ElectroMagnetic Compatibility and Radio spectrum Matters (ERM); Land
mobile service; Technical characteristics and test conditions for radio equipment for analogue
and/or digital communication (speech and/or data) and operating on narrowband channels and
having an antenna connector".
[i.13] ETSI EG 200 053: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio site
engineering for radio equipment and systems".
[i.14] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
3 D
...
Final draft ETSI EN 303 039 V1.1.1 (2014-01)
Harmonized European Standard
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Land Mobile Service; Multichannel transmitter
specification for the PMR Service;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 039 V1.1.1 (2014-01)
Reference
DEN/ERM-TGDMR-314
Keywords
data, mobile, PMR, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 039 V1.1.1 (2014-01)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 General . 11
4.1 Presentation of equipment for testing purposes . 11
4.1.1 Choice of model for testing . 11
4.1.1.1 Auxiliary test equipment . 11
4.1.1.2 Declarations by the provider . 11
4.2 Multi-Mode equipment . 12
4.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 12
5.3.1 Normal temperature and humidity . 12
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme test source voltages . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 14
5.5.1 Procedure for equipment designed for continuous transmission. 14
5.5.2 Procedure for equipment designed for intermittent transmission . 14
6 General test conditions . 15
6.1 Test bandwidth . 15
6.2 Test load (artificial antenna) . 15
6.3 Test signals (wanted and unwanted signals) . 15
6.3.1 Transmitter test signals for digital transmissions . 15
6.3.2 Encoder for digital transmitter measurements . 15
6.3.3 Transmitter test signals for analogue transmissions . 16
6.3.3.1 Test signals for frequency modulated channels. 16
6.3.3.2 Test signals for amplitude modulated channels. 16
6.3.3.3 Transmitter effective radiated power test signal (C1) . 16
6.4 Transceiver data interface for digital transmissions . 16
6.5 Impedance . 16
6.6 PEP . 16
6.7 Duplex equipment . 17
6.8 Modes of operation of the transmitter . 17
6.9 Measurement filter definition for digital transmissions . 17
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 039 V1.1.1 (2014-01)
7 Technical characteristics of the transmitter . 17
7.1 Transmitter output power (conducted) . 17
7.1.1 Definitions . 17
7.1.2 Method of measurement . 18
7.1.3 Limits . 18
7.2 Adjacent and alternate channel power . 18
7.2.1 Definition . 18
7.2.2 Method of measurement . 19
7.2.3 Limits . 22
7.3 Unwanted emissions . 23
7.3.1 Definition . 23
7.3.2 Method of measuring the power level . 24
7.3.2.1 Measurement options . 24
7.3.2.2 Method of measuring conducted spurious emissions (clause 7.3.2.1 a)) . 24
7.3.2.3 Method of measuring the effective radiated power (clause 7.3.2.1 b)) . 25
7.3.2.4 Method of measuring wideband noise. 26
7.3.2.5 Method for measuring frequency conversion oscillator conducted spurious emissions. 27
7.3.2.6 Method for measuring third order intermodulation products between wanted channels . 28
7.3.3 Limits . 28
7.3.3.1 Spurious emissions power . 28
7.3.3.2 Wideband noise power . 29
7.3.3.3 Frequency conversion oscillator spurious emission . 30
7.3.3.4 Third order intermodulation product spurious emission . 30
7.4 Intermodulation attenuation. 31
7.4.1 Definition . 31
7.4.2 Method of measurement . 31
7.4.3 Limits . 32
7.5 Transient power measurements . 32
7.5.1 Definition . 32
7.5.2 Method of Measurement . 32
7.5.3 Limits . 33
8 Measurement uncertainty . 33
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 35
Annex B (normative): Radiated measurement . 37
B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 37
B.1.1 Anechoic chamber . 37
B.1.2 Anechoic chamber with a conductive ground plane . 38
B.1.3 Open Area Test Site (OATS) . 39
B.1.4 Test antenna . 40
B.1.5 Substitution antenna . 41
B.1.6 Measuring antenna . 41
B.2 Guidance on the use of radiation test sites . 41
B.2.1 Verification of the test site . 41
B.2.2 Preparation of the EUT . 41
B.2.3 Power supplies to the EUT . 41
B.2.4 Range length . 42
B.2.5 Site preparation . 42
B.3 Coupling of signals . 43
B.3.1 General . 43
B.3.2 Data signals . 43
Annex C (normative): Spectrum analyser specification . 44
Annex D (informative): Bibliography . 45
History . 46
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 039 V1.1.1 (2014-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.4] as amended by Directive 98/48/EC [i.14].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.3].
See article 5.1 of Directive 1999/5/EC for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.3] are summarized in annex A.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.3]. The
modular structure is shown in EG 201 399 [i.2].
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 303 039 V1.1.1 (2014-01)
1 Scope
The present document covers the technical requirements for multiple channel radio transmitters used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel
separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 3 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue
speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF
channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two
or more RF channels. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal
or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter
output;
• and any equipment that may be used in combination with any of the above equipments when directly
connected to those equipments for the amplification of the transmitter output signals of two or more individual
equipments.
Types of equipment not covered by the present document are as follows:
• hand portable equipment without an external or internal RF connector and without the possibility of having a
temporary internal 50 Ω RF connector is not covered by the present document;
• any equipment using passive combining solutions where each transmitter connected to the passive combining
system transmits on a single channel, as detailed in EG 200 053 [i.13], clause H.3.
These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment,
the receiver specifications in the relevant specification (references [i.5] to [i.12]) should apply.
These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor
do they necessarily represent the optimum performance achievable.
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.3] (R&TTE
Directive), which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated
to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.3] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 303 039 V1.1.1 (2014-01)
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.153 (1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
[2] ETSI TR 100 028 (V1.4.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[3] ETSI TR 102 273 (V1.2.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties".
[4] ANSI C63.5 (2004): "American National Standard for Electromagnetic Compatibility-Radiated
Emission Measurements in Electromagnetic Interference (EMI) Control-Calibration of Antennas
(9 kHz to 40 GHz)".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] CEPT/ERC/REC 74-01 (2011): "Unwanted Emissions in the Spurious domain".
[i.2] ETSI EG 201 399 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
A guide to the production of candidate Harmonized Standards for application under the R&TTE
Directive".
[i.3] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.4] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.5] ETSI EN 300 392-2: "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air
Interface (AI)".
[i.6] ETSI EN 302 561: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment using constant or non-constant envelope modulation operating
in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz or 150 kHz; Harmonized EN covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.7] ETSI EN 300 086: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment with an internal or external RF connector intended primarily for
analogue speech".
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 303 039 V1.1.1 (2014-01)
[i.8] ETSI EN 300 113: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
mobile service; Radio equipment intended for the transmission of data (and/or speech) using
constant or non-constant envelope modulation and having an antenna connector".
[i.9] ETSI EN 300 296: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech".
[i.10] ETSI EN 300 341: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service (RP 02); Radio equipment using an integral antenna transmitting signals to initiate
a specific response in the receiver".
[i.11] ETSI EN 300 390: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an
integral antenna".
[i.12] ETSI EN 301 166: "ElectroMagnetic Compatibility and Radio spectrum Matters (ERM); Land
mobile service; Technical characteristics and test conditions for radio equipment for analogue
and/or digital communication (speech and/or data) and operating on narrowband channels and
having an antenna connector".
[i.13] ETSI EG 200 053: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio site
engineering for radio equipment and systems".
[i.14] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the
...
Draft ETSI EN 303 039 V1.1.0 (2013-04)
Harmonized European Standard
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Land Mobile Service; Multichannel transmitter
specification for the PMR Service;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 039 V1.1.0 (2013-04)
Reference
DEN/ERM-TGDMR-314
Keywords
data, mobile, PMR, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 039 V1.1.0 (2013-04)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 General . 10
4.1 Presentation of equipment for testing purposes . 10
4.1.1 Choice of model for testing . 11
4.1.1.1 Auxiliary test equipment . 11
4.1.1.2 Declarations by the provider . 11
4.2 Multi-Mode equipment . 11
4.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) . 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 12
5.3.1 Normal temperature and humidity . 12
5.3.2 Normal test power source . 13
5.3.2.1 Mains voltage . 13
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.3.2.3 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.2 Extreme test source voltages . 13
5.4.2.1 Mains voltage . 13
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 13
5.4.2.3 Power sources using other types of batteries . 14
5.4.2.4 Other power sources . 14
5.5 Procedure for tests at extreme temperatures . 14
5.5.1 Procedure for equipment designed for continuous transmission. 14
5.5.2 Procedure for equipment designed for intermittent transmission . 14
6 General test conditions . 15
6.1 Test bandwidth . 15
6.2 Test load (artificial antenna) . 15
6.3 Test signals (wanted and unwanted signals) . 15
6.3.1 Transmitter test signals for digital transmissions . 15
6.3.2 Encoder for digital transmitter measurements . 15
6.3.3 Transmitter test signals for analogue transmissions . 16
6.3.3.1 Test signals for frequency modulated channels. 16
6.3.3.2 Test signals for amplitude modulated channels. 16
6.3.3.3 Transmitter effective radiated power test signal (C1) . 16
6.4 Transceiver data interface for digital transmissions . 16
6.5 Impedance . 16
6.6 PEP . 16
6.7 Duplex equipment . 17
6.8 Modes of operation of the transmitter . 17
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 039 V1.1.0 (2013-04)
6.9 Measurement filter definition for digital transmissions . 17
7 Technical characteristics of the transmitter . 17
7.1 Transmitter output power (conducted) . 17
7.1.1 Definitions . 17
7.1.2 Method of measurement . 18
7.1.3 Limits . 18
7.2 Adjacent and alternate channel power . 18
7.2.1 Definition . 18
7.2.2 Method of measurement . 19
7.2.3 Limits . 22
7.3 Unwanted emissions . 23
7.3.1 Definition . 23
7.3.2 Method of measuring the power level . 24
7.3.2.1 Measurement options . 24
7.3.2.2 Method of measuring conducted spurious emissions (clause 7.3.2.1 a)) . 24
7.3.2.3 Method of measuring the effective radiated power (clause 7.3.2.1 b)) . 25
7.3.2.4 Method of measuring wideband noise. 26
7.3.2.5 Method for measuring frequency conversion oscillator conducted spurious emissions. 27
7.3.2.6 Method for measuring third order intermodulation products between wanted channels . 27
7.3.3 Limits . 28
7.3.3.1 Spurious emissions power . 28
7.3.3.2 Wideband noise power . 29
7.3.3.3 Frequency conversion oscillator spurious emission . 30
7.3.3.4 Third order intermodulation product spurious emission . 30
7.4 Intermodulation attenuation. 30
7.4.1 Definition . 30
7.4.2 Method of measurement . 31
7.4.3 Limits . 32
7.5 Transient power measurements . 32
7.5.1 Definition . 32
7.5.2 Method of Measurement . 32
7.5.3 Limits . 33
8 Measurement uncertainty . 33
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 35
Annex B (normative): Radiated measurement . 37
B.1 Test sites and general arrangements for measurements involving the use of radiated fields . 37
B.1.1 Anechoic chamber . 37
B.1.2 Anechoic chamber with a conductive ground plane . 38
B.1.3 Open Area Test Site (OATS) . 39
B.1.4 Test antenna . 40
B.1.5 Substitution antenna . 41
B.1.6 Measuring antenna . 41
B.2 Guidance on the use of radiation test sites . 41
B.2.1 Verification of the test site . 41
B.2.2 Preparation of the EUT . 41
B.2.3 Power supplies to the EUT . 41
B.2.4 Range length . 42
B.2.5 Site preparation . 42
B.3 Coupling of signals . 43
B.3.1 General . 43
B.3.2 Data signals . 43
Annex C (normative): Spectrum analyser specification . 44
Annex D (informative): Bibliography . 45
History . 46
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 039 V1.1.0 (2013-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been produced by ETSI in response to mandate M/284 from the European Commission
issued under Directive 98/34/EC [i.4] as amended by Directive 98/48/EC [i.14].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.3].
See article 5.1 of Directive 1999/5/EC for information on presumption of conformity and Harmonised Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.3] are summarized in annex A.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.3]. The
modular structure is shown in EG 201 399 [i.2].
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 039 V1.1.0 (2013-04)
1 Scope
The present document covers the technical requirements for multiple channel radio transmitters used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel
separations of <10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 3 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue
speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF
channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two
or more RF channels. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal
or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter
output.
• and any equipment that may be used in combination with any of the above equipments when directly
connected to those equipments for the amplification of the transmitter output signals of two or more individual
equipments.
Types of equipment not covered by the present document are as follows:
• hand portable equipment without an external or internal RF connector and without the possibility of having a
temporary internal 50 Ω RF connector is not covered by the present document;
• any equipment using passive combining solutions where each transmitter connected to the passive combining
system transmits on a single channel, as detailed in EG 200 053 [i.13], clause H.3.
These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment,
the receiver specifications in the relevant specification (references [i.5] to [i.12]) should apply.
These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor
do they necessarily represent the optimum performance achievable.
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.3] (R&TTE
Directive), which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated
to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.3] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 039 V1.1.0 (2013-04)
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-T O.153 (1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
[2] ETSI TR 100 028 (V1.4.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[3] ETSI TR 102 273 (V1.2.1) (2001) (all parts): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties".
[4] ANSI C63.5 (2004): "American National Standard for Electromagnetic Compatibility-Radiated
Emission Measurements in Electromagnetic Interference (EMI) Control-Calibration of Antennas
(9 kHz to 40 GHz)".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] CEPT/ERC/REC 74-01 (2011): "Unwanted Emissions in the Spurious domain".
[i.2] ETSI EG 201 399 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
A guide to the production of candidate Harmonized Standards for application under the R&TTE
Directive".
[i.3] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.4] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.5] ETSI EN 300 392-2: "Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air
Interface (AI)".
[i.6] ETSI EN 302 561: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land
Mobile Service; Radio equipment using constant or non-constant envelope modulation operating
in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz or 150 kHz; Harmonized EN covering
essential requirements of article 3.2 of the R&TTE Directive".
[i.7] ETSI EN 300 086: "Radio equipment with an internal or external RF connector intended primarily
for analogue speech".
[i.8] ETSI EN 300 113: "Radio equipment intended for the transmission of data (and/or speech) using
constant or non-constant envelope modulation and having an antenna connector".
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 039 V1.1.0 (2013-04)
[i.9] ETSI EN 300 296: "Radio equipment using integral antennas intended primarily for analogue
speech".
[i.10] ETSI EN 300 341: "Radio equipment using an integral antenna transmitting signals to initiate a
specific response in the receiver".
[i.11] ETSI EN 300 390: "Radio equipment intended for the transmission of data (and speech) and using
an integral antenna".
[i.12] ETSI EN 301 166: "Technical characteristics and test conditions for radio equipment for analogue
and/or digital communication (speech and/or data) and operating on narrowband channels and
having an antenna connector".
[i.13] ETSI EG 200 053: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio site
engineering for radio equipment and systems".
[i.14] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
base station: equipment fitted with an antenna connector, for use with an external antenna, and intended for use in a
fixed location
bit: binary digit
block: smallest quantity of information that is sent over the radio channel
NOTE: A constant number of useful bits are always sent together with the corresponding redundancy bits.
burst or transmission (physical): one or several packets transmitted between power on and power off of a particular
transmitter
channel: width of a single frequency
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.