SIST EN 301 908-5:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS) and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 5: Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (BS) covering essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-5 Version 1.1.136IST EN 301 908-5:2002en01-VHSWHPEHU-20023SIST EN 301 908-5:2002SLOVENSKI
STANDARD



SIST EN 301 908-5:2002



ETSI EN 301 908-5 V1.1.1 (2002-01)Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Base Stations (BS) and User Equipment (UE) forIMT-2000 Third-Generation cellular networks;Part 5: Harmonized EN for IMT-2000,CDMA Multi-Carrier (cdma2000) (BS)covering essential requirementsof article 3.2 of the R&TTE Directive SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 2
Reference DEN/ERM-TFES-001-5 Keywords 3G, 3GPP2, cdma2000, cellular, digital, IMT-2000, mobile, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editor@etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2002. All rights reserved.
SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 3 Contents Intellectual Property Rights.5 Foreword.5 Introduction.7 1 Scope.9 2 References.9 3 Definitions, symbols and abbreviations.10 3.1 Definitions.10 3.2 Symbols.17 3.3 Abbreviations.19 4 Technical requirements specifications.20 4.1 Environmental profile.20 4.2 Conformance requirements.20 4.2.1 Introduction.20 4.2.2 Transmitter conducted spurious emissions.20 4.2.2.1 Definition.20 4.2.2.2 Limits.21 4.2.2.3 Conformance.21 4.2.3 Maximum output power.21 4.2.3.1 Definition.21 4.2.3.2 Limits.21 4.2.3.3 Conformance.21 4.2.4 Inter-base station transmitter intermodulation.22 4.2.4.1 Definition.22 4.2.4.2 Limits.22 4.2.4.3 Conformance.22 4.2.5 Receiver conducted spurious emissions.22 4.2.5.1 Definition.22 4.2.5.2 Limits.22 4.2.5.3 Conformance.22 4.2.6 Receiver blocking characteristics.22 4.2.6.1 Definition.22 4.2.6.2 Limits.23 4.2.6.3 Conformance.23 4.2.7 Intermodulation spurious response attenuation.23 4.2.7.1 Definition.23 4.2.7.2 Limits.23 4.2.7.3 Conformance.23 4.2.8 Adjacent channel selectivity.23 4.2.8.1 Definition.23 4.2.8.2 Limits.23 4.2.8.3 Conformance.23 5 Testing for compliance with technical requirements.24 5.1 Conditions for testing.24 5.1.1 Introduction.24 5.1.2 Standard equipment under test.24 5.1.2.1 Basic equipment.24 5.1.2.2 Ancillary equipment.24 5.2 Interpretation of the measurement results.24 5.3 Essential radio test suites.25 5.3.1 Transmitter conducted spurious emissions.25 5.3.2 Maximum output power.25 5.3.3 Inter-base station transmitter intermodulation.26 5.3.4 Receiver conducted spurious emissions.26 SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 4 5.3.5 Receiver blocking characteristics.26 5.3.6 Intermodulation spurious response attenuation.27 5.3.7 Adjacent channel selectivity.28 Annex A (normative): The EN Requirements Table (EN-RT).29 Annex B (informative): Environmental profile and standard test conditions.30 B.1 Introduction.30 B.2 CDMA environmental requirements.30 B.2.1 Temperature and power supply voltage.30 B.2.1.1 Definition.30 B.2.1.2 Method of measurement.30 B.2.1.3 Minimum standard.31 B.2.2 High humidity.31 B.2.2.1 Definition.31 B.2.2.2 Method of measurement.31 B.2.2.3 Minimum standard.31 B.3 Standard test conditions.31 B.3.1 Standard environmental test conditions.31 B.3.2 Standard conditions for the primary power supply.32 B.3.2.1 General.32 B.3.2.2 Standard DC test voltage from accumulator batteries.32 B.3.2.3 Standard AC voltage and frequency.32 Annex C (informative): The EN title in the official languages.33 Annex D (informative): Bibliography.34 History.35
SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive"). The present document is part 5 of a multi-part deliverable covering the Base Stations (BS) and User Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below: Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering essential requirements of article 3.2 of the R&TTE Directive"; Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 7: "Harmonized standard for IMT-2000, CDMA TDD (UTRA TDD) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 10: "Harmonized EN for IMT-2000 FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive". SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 6 Technical specifications relevant to Directive 1999/5/EC are given in annex A.
National transposition dates Date of adoption of this EN: 4 January 2002 Date of latest announcement of this EN (doa): 30 April 2002 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 October 2002 Date of withdrawal of any conflicting National Standard (dow): 31 October 2003
SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 7 Introduction The present document is part of a set of standards designed to fit in a modular structure to cover all radio and telecommunications terminal equipment under the R&TTE Directive [1]. Each standard is a module in the structure. The modular structure is shown in figure 1.
- If needed, new standards for human exposure to Electromagnetic Fields, - if needed, new standards for acoustic safety Use of spectrum * If needed Scoped by
equipment
class or type Scoped by frequency and/or equipment type Disability* Privacy* Fraud* No harm to the network* Emergency* Interworking via
the network* Interworking with the network Non-radio Radio (RE) Non-TTE TTE 3.1b 3.2 3.3c 3.3b 3.3a 3.3d 3.3e 3.3f Radio Product EMC EN 301 489 multi-part EMC standard Generic and product standards also notified under EMC Directive Standards also notified under LV Directive 3.1a New radio harmonized standards Spectrum EMC Safety
Figure 1: Modular structure for the various standards used under the R&TTE Directive SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 8 The left hand edge of the figure 1 shows the different clauses of article 3 of the R&TTE Directive. For article 3.3 various horizontal boxes are shown. Dotted lines indicate that at the time of publication of the present document essential requirements in these areas have to be adopted by the Commission. If such essential requirements are adopted, and as far and as long as they are applicable, they will justify individual standards whose scope is likely to be specified by function or interface type. The vertical boxes show the standards under article 3.2 for the use of the radio spectrum by radio equipment. The scopes of these standards are specified either by frequency (normally in the case where frequency bands are harmonized) or by radio equipment type. For article 3.1b figure 1 shows EN 301 489 [10], the multi-part product EMC standard for radio used under the EMC Directive [2]. For article 3.1a figure 1 shows the existing safety standards currently used under the LV Directive [3] and new standards covering human exposure to electromagnetic fields. New standards covering acoustic safety may also be required. The bottom of figure 1 shows the relationship of the standards to radio equipment and telecommunications terminal equipment. A particular equipment may be radio equipment, telecommunications terminal equipment or both. A radio spectrum standard will apply if it is radio equipment. An article 3.3 standard will apply as well only if the relevant essential requirement under the R&TTE Directive is adopted by the Commission and if the equipment in question is covered by the scope of the corresponding standard. Thus, depending on the nature of the equipment, the essential requirements under the R&TTE Directive [1] may be covered in a set of standards. The modularity principle has been taken because: • it minimizes the number of standards needed. Because equipment may, in fact, have multiple interfaces and functions it is not practicable to produce a single standard for each possible combination of functions that may occur in an equipment; •
it provides scope for standards to be added: - under article 3.2 when new frequency bands are agreed; or - under article 3.3 should the Commission take the necessary decisions without requiring alteration of standards that are already published; • it clarifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment. The product specifications upon which this present multi-part deliverable is based differ in presentation, and this is reflected in the present document. SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 9 1 Scope The present document applies to the following radio equipment types: •
Base stations for IMT-2000 CDMA Multi-Carrier (cdma2000). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. Table 1: CDMA Multi-Carrier base station service frequency bands Direction of transmission CDMA Multi-Carrier base station service frequency bands Transmit 2 110 MHz to 2 170 MHz Receive 1 920 MHz to 1 980 MHz
The present document is intended to cover the provisions of Directive 1999/5/EC [1] (R&TTE Directive) article 3.2, which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org/. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. [1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [2] Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive). [3] Council Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (LV Directive). [4] ANSI/TIA/EIA-97-D-2001: "Recommended Minimum Performance Standards for Base Stations Supporting Dual Mode Spread Spectrum Systems". [5] ANSI/TIA/EIA/IS-2000.2-A-1-2000: "Physical Layer Standard for cdma2000 Spread Spectrum Systems". [6] ANSI/TIA/EIA-98-D-2001: "Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations". [7] ANSI/TIA/EIA126-D-2001: "Loopback Service Options (LSO) for cdma2000 Spread Spectrum Systems". SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 10 [8] ANSI/TIA/EIA/IS-870-April 2001: "Test Data Service Option (TDSO) for cdma2000 Spread Spectrum Systems". [9] TIA/EIA/IS-871-April 2001: "Markov Service Option (MSO) for cdma2000 Spread Spectrum Systems". [10] ETSI EN 301 489 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the R&TTE Directive [1], and the following apply. access attempt: sequence of one or more access probe sequences on the Access Channel or Enhanced Access Channel containing the same message NOTE: See also Access Probe, Access Probe Sequence, and Enhanced Access Probe. access channel: reverse CDMA Channel used by mobile stations for communicating to the base station NOTE: The Access Channel is used for short signalling message exchanges, such as call originations, responses to pages, and registrations. The Access Channel is a slotted random access channel. access channel preamble: preamble of an access probe consisting of a sequence of all-zero frames that is sent at the 4 800 bps rate access probe: one Access Channel transmission consisting of a preamble and a message NOTE: The transmission is an integer number of frames in length, and transmits one Access Channel message. See also Access Probe Sequence and Access Attempt. access probe sequence: sequence of one or more access probes on the Access Channel or Enhanced Access Channel NOTE: The same Access Channel or Enhanced Access Channel message is transmitted in every access probe of an access attempt. See also Access Probe, Enhanced Access Probe, and Access Attempt. active frame: frame that contains data and therefore is enabled in terms of traffic power additional preamble: preamble sent after the last fractional preamble on the Reverse Pilot Channel, prior to transmitting on the Enhanced Access Channel or on the Reverse Common Control Channel adjacent channel leakage ratio: ratio of the on-channel transmit power to the power measured in one of the adjacent channels bad frame: frame classified with insufficient frame quality or for Radio Configuration 19 600 bps primary traffic only, with bit errors NOTE: See also Good Frame. band class: set of frequency channels and a numbering scheme for these channels NOTE: Band classes are defined in ANSI/TIA/EIA-97-D [4], clause 3.1, and ANSI/TIA/EIA-98-D [6], clause 3.1. band class 6: frequencies as identified in table 1 of the EN 301 908-5 base station: fixed station used for communicating with mobile stations NOTE: Depending upon the context, the term base station may refer to a cell, a sector within a cell, an MSC, or other part of the wireless system. See also MSC. SIST EN 301 908-5:2002



ETSI ETSI EN 301 908-5 V1.1.1 (2002-01) 11 basic access mode: mode used on the Enhanced Access Channel where a mobile station transmits an Enhanced Access Channel preamble and Enhanced Access data in a method similar to that used on the Access Channel broadcast control channel: code channel in a Forward CDMA Channel used for transmission of control information from a base station to a mobile station candidate frequency: frequency for which the base station specifies a search set, when searching on other frequencies while performing mobile-assisted handoffs CDMA channel: set of channels transmitted from the base station and the mobile stations on a given frequency CDMA channel number: 11-bit number corresponding to the center of the CDMA frequency assignment CDMA frequency assignment: 1,23 MHz segment of spectrum. For Band Class 0, the channel is centered on one of the 30 kHz channels. For Band Classes 1, 4, 6, 7, 8, and 9, the channel is centered on one of the 50 kHz channels. For Band Classes 2 and 3, the channel is centered on one of the 25 kHz channels. For Band Class 5, the channel is centered on one of the 20 kHz or 25 kHz channels. CDMA preferred set: set of CDMA channel numbers in a CDMA system corresponding to frequency assignments that a mobile station will normally search to acquire a CDMA Pilot Channel code channel: subchannel of a Forward CDMA Channel or Reverse CDMA Channel. Each subchannel uses an orthogonal Walsh function or quasi-orthogonal function Code Division Multiple Access (CDMA): technique for spread-spectrum multiple-access digital communications that creates channels through the use of unique code sequences code symbol: output of an error-correcting encoder. Information bits are input to the encoder and code symbols are output from the encoder. See Convolutional Code and Turbo Code common assignment channel: forward common channel used by the base station to acknowledge a mobile station accessing the Enhanced Access Channel, and in the case of Reservation Access Mode, to transmit the address of a Reverse Common Control Channel and associated Common Power Control Subc
...