SIST EN 60464-3-2:2002

SLOVENSKI SIST EN 60464-3-2:2002
prva izdaja
STANDARD
oktober 2002
Varnishes used for electrical insulation - Part 3: Specifications for individual
materials - Sheet 2: Hot curing impregnating varnishes (IEC 60464-3-2:2001)
ICS 29.035.60 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 60464-3-2
NORME EUROPÉENNE
EUROPÄISCHE NORM September 2001
ICS 29.035.01
English version
Varnishes used for electrical insulation
Part 3: Specifications for individual materials
Sheet 2: Hot curing impregnating varnishes
(IEC 60464-3-2:2001)
Vernis utilisés comme isolant électrique Elektroisolierlacke
Partie 3: Spécifications pour matériaux Teil 3: Bestimmungen für einzelne
particuliers Materialien
Feuille 2: Vernis d'imprégnation durcissant Blatt 2: Heißhärtende Tränklacke
à chaud (IEC 60464-3-2:2001)
(CEI 60464-3-2:2001)
This European Standard was approved by CENELEC on 2001-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,
Portugal, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60464-3-2:2001 E
Foreword
The text of document 15C/1222/FDIS, future edition 2 of IEC 60464-3-2, prepared by SC 15C,
Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 60464-3-2 on 2001-09-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2002-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2004-09-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60464-3-2:2001 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60464-3-2:2001
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60172 1987 Test procedure for the determination of EN 60172 1994
the temperature index of enamelled
winding wires
IEC 60317-8 1990 Specifications for particular types of EN 60317-8 1994
winding wires
Part 8: Polyesterimide enamelled round
copper wire, class 180
IEC 60317-13 1990 Part 13: Polyester or polyesterimide EN 60317-13 1994
overcoated with polyamide-imide
enamelled round copper wire, class 200
IEC 60464-1 1998 Varnishes used for electrical insulation EN 60464-1 1999
Part 1: Definitions and general
requirements
IEC 60464-2 2001 Part 2: Methods of test EN 60464-2 2001
IEC 61033 1991 Test methods for the determination of--
bond strength of impregnating agents to
an enamelled wire substrate
NORME CEI
INTERNATIONALE IEC
60464-3-2
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2001-07
Vernis utilisés pour l'isolation électrique –
Partie 3:
Spécifications pour matériaux particuliers –
Feuille 2: Vernis d’imprégnation durcissant
à chaud
Varnishes used for electrical insulation –
Part 3:
Specifications for individual materials –
Sheet 2: Hot curing impregnating varnishes
 IEC 2001 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun procédé, any form or by any means, electronic or mechanical,
électronique ou mécanique, y compris la photocopie et les including photocopying and microfilm, without permission in
microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http://www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
H
PRICE CODE
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue

60464-3-2  IEC:2001 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
VARNISHES USED FOR ELECTRICAL INSULATION –
Part 3: Specifications for individual materials –
Sheet 2: Hot curing impregnating varnishes
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60464-3-2 has been prepared by subcommittee 15C: Specifications,
of IEC te
...