SIST EN 300 474-2 V1.2.1:2003

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.7Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 2: Fixed radio Termination (FT)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:EN 300 474-2 Version 1.2.1SIST EN 300 474-2 V1.2.1:2003en01-december-2003SIST EN 300 474-2 V1.2.1:2003SLOVENSKI
STANDARD
ETSI EN 300 474-2 V1.2.1 (2003-09)European Standard (Telecommunications series) Digital Enhanced Cordless Telecommunications (DECT);Generic Access Profile (GAP);Profile requirement list and profile specificImplementation Conformance Statement (ICS) proforma;Part 2: Fixed radio Termination (FT)
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 2
Reference REN/DECT-040107-2 Keywords access, DECT, generic, ICS, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editor@etsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2003. All rights reserved.
DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. SIST EN 300 474-2 V1.2.1:2003

ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 3
Contents Intellectual Property Rights.5 Foreword.5 1 Scope.6 2 References.6 3 Definitions and abbreviations.7 3.1 Definitions.7 3.2 Abbreviations.7 4 Conformance requirement concerning profile ICS.7 Annex A (normative): Requirement Lists for DECT FT.8 A.1 General.8 A.1.1 Profile Requirement List (profile RL).8 A.1.2 General conditions.9 A.2 Network (NWK) layer - FT: profile Requirement List (profile RL).9 A.2.1 Major capabilities.9 A.2.1.1 Entities.9 A.2.1.2 CC features.10 A.2.1.3 MM features.11 A.2.1.4 SS features (services).12 A.2.1.5 LCE features.13 A.2.1.6 Procedures.13 A.2.2 Messages.15 A.2.2.1 Call control messages.15 A.2.2.2 Mobility management messages.22 A.2.2.3 Connection-related and connection independent supplement service messages.28 A.2.2.4 Link control entity messages.28 A.2.3 Information elements.29 A.2.3.1 Fixed length information element support.29 A.2.3.2 Variable length information element supported.30 A.2.3.3 Escape information elements support.34 A.2.4 Protocol error handling.35 A.3 Data Link Control (DLC) layer - FT: profile ICS.35 A.3.1 Capabilities.35 A.3.1.1 Services.35 A.3.1.1.1 C-plane services.35 A.3.1.1.2 U-plane services.36 A.3.1.1.3 Management services.36 A.3.1.2 Procedures.36 A.3.1.2.1 Generic signalling procedures.36 A.3.1.2.2 Class A procedures.37 A.3.1.2.3 Broadcast procedures.37 A.3.1.2.4 LU1 procedures.37 A.3.1.2.5 Management procedures.37 A.3.1.3 Parameters.38 A.3.1.3.1 LU1 parameters.38 A.3.1.4 Messages.38 A.3.1.4.1 C-plane PDUs.38 A.4 Medium Access Control (MAC) layer - FT: profile ICS.39 A.4.1 Major capabilities.39 A.4.1.1 Services.39 A.4.1.1.1 Connection oriented control services.39 A.4.1.1.2 Broadcast control services.40 SIST EN 300 474-2 V1.2.1:2003

ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 4
A.4.1.1.3 Multiplexing services.40 A.4.1.1.4 Management services.41 A.4.1.2 Procedures.42 A.4.1.2.1 Connection setup procedures.42 A.4.1.2.2 Connection data transfer procedures.42 A.4.1.2.3 Connection handover procedures.42 A.4.1.2.4 Connection release procedures.43 A.4.1.2.5 Broadcast procedures.43 A.4.1.2.6 CSF multiplexing procedures.43 A.4.1.2.7 Layer management procedures.43 A.4.1.3 Other capabilities.44 A.4.2 Messages.44 A.4.2.1 A-Field.44 A.4.2.1.1 A-field header - B-field identification.44 A.4.2.2 A-Field Messages.45 A.4.2.2.1 Paging tail messages supported.45 A.4.2.2.2 PT messages information type.45 A.4.2.2.3 Mac control messages supported.46 A.4.2.2.4 Broadcast and connectionless (BCL) messages.46 A.5 Physical layer - FT: profile ICS.47 A.5.1 Physical layer procedures.47 Annex B (normative): GAP profile-specific ICS proforma for FT.48 B.1 Introduction for completing the profile-specific ICS proforma.48 B.1.1 Purposes and structure.48 B.1.2 Instructions for completing the profile-specific ICS proforma.50 B.2 Identification of the implementation.50 B.2.1 Date of statement.50 B.2.2 Implementation Under Test (IUT) identification.50 B.2.3 System Under Test (SUT) identification.50 B.2.4 Product supplier.51 B.2.5 Client identification.51 B.2.6 Contact person identification.51 B.3 Identification of the profile.52 B.3.1 Defect report numbers and amendments implemented.52 B.3.2 Addenda implemented.52 B.4 Global statement of conformance.52 B.5 Capabilities.53 B.5.1 NWK profile-specific ICS proforma for FT.53 B.5.1.1 General requirements.53 B.5.1.2 Application features.53 B.5.1.3 Application procedures.53 B.5.1.4 Management procedures.54 B.5.2 DLC profile-specific ICS proforma for FT.54 B.5.2.1 Services.54 B.5.3 MAC profile-specific ICS proforma for FT.54 B.5.3.1 Services.54 B.5.3.1.1 Extended frequency allocation service.54 B.5.4 PHY Profile-specific ICS proforma for FT.55 B.5.4.1 Requirements.55 Annex C (informative): Bibliography.56 History.57
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 5
Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced Cordless Telecommunications (DECT). The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in EN 300 474-1 [9]. Annex A contains the requirement lists for the Fixed radio Termination (FT) Generic Access Profile. Annex B contains the profile-specific ICS proforma for the FT Generic Access Profile.
National transposition dates Date of adoption of this EN: 5 September 2003 Date of latest announcement of this EN (doa): 31 December 2003 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2004 Date of withdrawal of any conflicting National Standard (dow): 30 June 2004
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 6
1 Scope The present document provides the profile Requirement List and profile-specific Implementation Conformance Statement (profile ICS) proforma for the Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP) at the Fixed radio Termination (FT) as defined in EN 300 444 [2] in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 [8]. The supplier of an implementation which is claimed to conform to EN 300 444 [2] is required to complete a copy of the Protocol Implementation Conformance Statement (PICS) proforma EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] and EN 300 476-7 [6] with the replacements from annex A of the present document, as well as, a copy of the and profile-specific ICS proforma provided in the annex B of the present document. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. [1] ETSI EN 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 5: Network (NWK) layer". [2] ETSI EN 300 444: "Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP)". [3] ETSI EN 300 476-4: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma;
Part 4: Network (NWK) layer - Fixed radio Termination (FT)". [4] ETSI EN 300 476-5: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 5: Data Link Control (DLC) layer - Fixed radio Termination (FT)". [5] ETSI EN 300 476-6: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma;
Part 6: Medium Access Control (MAC) layer - Fixed radio Termination (FT)". [6] ETSI EN 300 476-7: "Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma;
Part 7: Physical layer". [7] ISO/IEC 9646-1 (1994): "Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts". [8] ISO/IEC 9646-7 (1995): "Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements". [9] ETSI EN 300 474-1: "Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma; Part 1: Portable radio Termination (PT)". SIST EN 300 474-2 V1.2.1:2003

ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 7
3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-7 [8], EN 300 444 [2] and ISO/IEC 9646-1 [7] apply. 3.2 Abbreviations For the purposes of the present document, the abbreviations defined in ISO/IEC 9646-1 [7] and EN 300 444 [2] apply. 4 Conformance requirement concerning profile ICS The supplier of a protocol implementation which is claimed to conform to the portable termination specific requirements of EN 300 444 [2] shall verify that his protocol implementation meets the profile Requirements Lists (RLs) for each DECT protocol layer, contained in annex A of the present document, and shall complete a copy of the profile-specific ICS proforma provided in annex B and shall provide the information necessary to identify both the supplier and the implementation. SIST EN 300 474-2 V1.2.1:2003

ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 8
Annex A (normative): Requirement Lists for DECT FT A.1 General The supplier of a protocol implementation which is claimed to conform to the portable termination specific requirements of EN 300 444 [2] shall verify that his particular (NWK, DLC and MAC) layer protocol implementation meets the profile RL for this layer. For this, he shall complete a copy of the corresponding layer PICS proforma contained in annex A of EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] and EN 300 476-7 [6] updated with the requirements from this annex. A.1.1 Profile Requirement List (profile RL) The profile Requirement List (profile RL) for the NWK, DLC, MAC and PH layer as defined in this clause is based on EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] and EN 300 476-7 [6]. For every capability listed in EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] and EN 300 476-7 [6], the profile requirements are expressed by restriction upon allowed support answers in EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] and EN 300 476-7 [6] depending on whether the implementation is to work in Residential/Business (R/B) or Public (P) environment. The profile RL is produced by copying selected tables from EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] and EN 300 476-7 [6], removing the column(s) to be completed by the supplier, and adding a new set of columns giving the new profile requirements, both in terms of the status and allowed values. The tables are referenced by preceding it with EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] or EN 300 476-7 [6] as relevant. Profile status column: Where it has been seen as necessary two profile status columns are provided one for Residential/Business (R/B) environment and one for Public (P) environment. The standardized symbols for the status column are as follows: • m or M mandatory - the capability is required to be supported; • o or O optional - the capability may be supported or not; • n/a or N/A not applicable - in the given context, it is impossible to use the capability; • x or X prohibited (excluded) - there is a requirement not to use this capability in the given context; • o.i or O.i qualified optional - for mutually exclusive or selectable options from a set. "i" is an integer which
identifies a unique group of related optional items and the logic of their selection which is defined
immediately following the table; • ci or Ci conditional - the requirement on the capability ("m", "o", "x" or "n/a") depends on the support of
other optional or conditional items. "i" is an integer identifying a unique conditional status
expression which is defined immediately following the table or which is defined in the general
condition table below; • i or I out-of-scope - this capability is outside the scope of the given specification, and hence irrelevant
and not subject to conformance testing. This status is in particular applicable for data fields which
are reserved for future use. The structure of such fields has to be supported, but the value is
undefined and thus to be ignored. Reference column: The reference column gives reference to EN 300 444 [2], except where explicitly stated otherwise. SIST EN 300 474-2 V1.2.1:2003

ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 9
A.1.2 General conditions The note in table A.1 is generally defined to apply to the tables in the following clauses where indicated. Table A.1: General condition table Condition identifier Condition definition NOTE A The status of the relevant item is exactly as the status of this item in EN 300 476-4 [3], EN 300 476-5 [4], EN 300 476-6 [5] and EN 300 476-7 [6]. The item has been included as the profile reference column includes reference to the profile that describes the item more in details.
A.2 Network (NWK) layer - FT: profile Requirement List (profile RL) A.2.1 Major capabilities A.2.1.1 Entities To express the profile requirements of EN 300 444 [2], the following table indicates the change of status for support of entities. Table A.2: Profile modification for EN 300 476-4 [3] table A.12 Entity supported Item Entity name Profile reference Profile status R/B Profile status P 1 Call control (CC) 6.2 m m 2 Call Independent Supplementary Services (CISS) - i i 3 Connection oriented message services (COMS) - i i 4 ConnectionLess message services (CLMS) - i i 5 Mobility management (MM) 6.2 m m 6 Link control entity (LCE) 6.2 m m 7 Management (LLME) 13 m m
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 10 A.2.1.2 CC features To express the profile requirements of EN 300 444 [2], the following table indicates the change of status for support of NWK layer CC features. Table A.3: Profile modification for EN 300 476-4 [3] table A.13 CC features supported Item Call Control features Profile reference Profile status R/B Profile status P 1 Bell off (Alerting) 6.2 m m 2 Bell on (Alerting) 6.2 m m 3 Control of supervisory tones - i i 4 Dial tone detection indication - i i 5 Dialled digits (basic) 6.2 m m 6 Dialled digits additional - i i 7 Dialling delimiter - i i 8 Dialling delimiter request - i i 9 Display control characters 6.2 o o 10 Emergency service access request - i i 11 External Handover (inter-cell) - i i 12 Fixed part/portable part capability exchange - i i 13 Go to DTMF (infinite tone length) 6.2 o o 14 Go to DTMF signalling (defined tone length) 6.2 o m 15 Go to Pulse 6.2 o o 16 Group address - i i 17 Incoming call 6.2 m m 18 Internal call 6.2 o o 19 Off hook 6.2 m m 20 On hook (full release) 6.2 m m 21 Outgoing call
6.2 m m 22 Packet mode - i i 23 Partial release 6.2 o o 24 Pause (dialling pause) 6.2 o o 25 Register recall
6.2 o o 26 Signalling of display characters 6.2 o o 27 Selection of bearer service - i i 28 Service call 6.2 o o 29 Service change - i i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 11 A.2.1.3 MM features To express the profile requirements of EN 300 444 [2], the following table indicates the change of status for support of NWK layer MM features. Table A.4: Profile modification for EN 300 476-4 [3] table A.14 MM features supported Item Mobility Management features Profile reference Profile status R/B Profile status P 1 Authentication of FT 6.2 o o 2 Authentication of PT 6.2 o m 3 Authentication of user
6.2 o o 4 Encryption activation FT initiated 6.2 o m 5 Encryption activation PT initiated 6.2 o o 6 Encryption deactivation FT initiated 6.2 o o 7 Encryption deactivation PT initiated 6.2 o o 8 Identification of PP 6.2 o o 9 Inter-operator roaming registration - i i 10 Location de-registration - i i 11 Location registration 6.2 o m 12 Multiple subscription registration 6.6 n/a n/a 13 On air key allocation
6.2 o o 14 Service class indication/assignment 6.2 o m 15 Silent polling - i i 16 Subscription registration procedure on-air 6.2 m m 17 Subscription registration user procedure with DECT authentication module - i i 18 Subscription registration user procedures keypad (digit entry only) - i i 19 Terminate access rights FT initiated 6.2 o o 20 Terminate access rights PT initiated - i i 21 ZAP 6.2 o o 22 MM Partial release 8.39 m m 23 Temporary identity assign - i i 24 Modification access rights - i i 25 Temporary identity assignment with location registration - i i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 12 A.2.1.4 SS features (services) To express the profile requirements of EN 300 444 [2], the following table indicates the change of status for support of NWK layer SS features (services). Table A.5: Profile modification for EN 300 476-4 [3] table A.15 SS features (services) supported Item CC(CRSS) and CISS features Profile reference. Profile status R/B Profile status P 1 Advice Of Charge (AOC) - i i 2 Advice of tariff request - i i 3 Call Deflection (CD) - i i 4 Call Forwarding Busy (CFB) - i i 5 Call Forwarding No Reply (CFNR) - i i 6 Call Forwarding Unconditional (CFU) - i i 7 Call Waiting (CW) - i i 8 Calling Line Identification Presentation (CLIP) 6.2 o o 9 Calling Line Identification Restriction (CLIR) - i i 10 Closed User Group (CUG) - i i 11 Completion of Calls to Busy Subscriber (CCBS) - i i 12 Call Hold (CH) - i i 13 CONFerence call add-on (CONF) - i i 14 COnnected Line identification Presentation (COLP) - i i 15 COnnected Line identification Restriction (COLR) - i i 16 Control of echo control functions - i i 17 Cost information - i i 18 Credit agency public access service - i i 19 Credit public access service - i i 20 Debit public access service - i i 21 Direct Dialling In (DDI) - i i 22 Explicit Call Transfer (ECT) - i i 23 Forced re-connection of held call - i i 24 FreePHone (FPH) - i i 25 Hold call (FT to PT) - i i 26 Hold call (PT to FT) - i i 27 Indication of teleservice available request - i i 28 Indication of teleservices available - i i 29 Malicious Call IDentification (MCID) - i i 30 Multiple Subscriber Number (MSN) - i i 31 On-demand (hot bill) public access service- CRSS - i i 32 Queue management - i i 33 Re-connection of held call (FT to PT) - i i 34 Re-connection of held call (PT to FT) - i i 35 Request for indication of temporary subscriber number- CRSS - i i 36 Selection of required teleservice - i i 37 Single step Call Transfer (SCT) - i i 38 Specific trunk carrier selection - i i 39 SUBaddressing (SUB) - i i 40 Terminal Portability (TP) - i i 41 Tree ParTY (3TPY) - i i 42 User to User Signalling UUS - i i 43 CISS Partial release - i i 44 Feature key - i i 45 Indication of subscriber number - i i 46 Register recall - i i 47 Specific line selection - i i 48 External handover switch - i i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 13 A.2.1.5 LCE features To express the profile requirements of EN 300 444 [2], the following table indicates the change of status for support of NWK layer LCE features. Table A.6: Profile modification for EN 300 476-4 [3] table A.16 LCE features supported Item LCE features Profile reference Profile status R/B Profile status P 1 Connection oriented Link control (Link control) 6.2 m m 2 Connectionless oriented Link control - i i
A.2.1.6 Procedures To express the profile requirements of EN 300 444 [2], the following tables indicate the change of status for support of NWK layer procedures. Table A.7: Profile modification for EN 300 476-4 [3] table A.18 CC procedures supported Item CC procedures Profile reference Profile status R/B Profile status P 1 cc_outgoing_normal_call_request 8.2 m m 4 cc_outgoing_selection_of_lower_layer_resources - i i 5 cc_outgoing_connection_of_U_plane 8.3, 8.4, 8.5, 8.6 m m 6 cc_outgoing_overlap_sending 8.3 o o 7 cc_outgoing_call_proceeding 8.4 o o 8 cc_outgoing_call_confirmation 8.5 o o 9 cc_outgoing_call_connection 8.6 m m 10 cc_incoming_call_request 8.12 m m 11 cc_incoming_selection_of_lower_layer_resources - i i 12 cc_incoming_connection_of_U_plane 8.15 m m 13 cc_incoming_overlap_receiving - i i 14 cc_incoming_call_proceeding - i i 15 cc_incoming_call_confirmation 8.13 m m 16 cc_incoming_call_connection 8.15 m m 17 cc_sending_terminal_capability - i i 18 cc_sending_keypad_info 8.10 m m 19 cc_call_information 8.10 i i 20 cc_normal_call_release 8.7 m m 21 cc_partial_release 8.9 note A note A 22 cc_abnormal_call_release 8.8 m m 23 cc_release_collisions 8.7.2.1 m m 31 cc_timer_f_cc_02_mgt 8.7 m m 32 cc_timer_f_cc_03_mgt 8.2 m m 33 cc_timer_f_cc_04_mgt - i i 34 cc_timer_f_cc_01_mgt 8.3 note A note A 35 cc_internal_call_setup 8.18 c.a701 c.a701 36 cc_service_call_setup 8.20 c.a702 c.a702 38 cc_service_call_keypad 8.21 c.a703 c.a703 39 cc_internal_call_keypad 8.19 c.a704 c.a704 40 pt_alerting 8.14 m m 41 display 8.16 note A note A c.a701: IF A.3/18 THEN m ELSE i. c.a702: IF A.3/18 THEN o ELSE i. c.a703: IF A.3/28 THEN m ELSE i. c.a704: IF A.3/28 THEN o ELSE i.
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 14 Table A.8: Profile modification for EN 300 476-4 [3] table A.19 MM procedures supported Item Mobility Management procedures Profile reference Profile status R/B Profile status P 1 mm_identification_of_pt 8.22 note A note A 2 mm_temporary_identity_assignment - i i 3 mm_authentication_of_pt 8.24 note A note A 4 mm_authentication_of_user 8.25 note A note A 5 mm_authentication_of_ft 8.23 note A note A 6 mm_location_registration 8.28 note A note A 8 mm_location_update 8.29 c.a801 note A 9 mm_obtain_access_rights 8.30 m m 10 mm_pt_init_terminate_access_rights - i i 11 mm_ft_init_terminate_access_rights 8.31 note A note A 12 mm_key_allocation 8.32 note A note A 13 mm_pt_init_parameter_retrieval - i i 14 mm_ft_init_parameter_retrieval - i i 15 mm_pt_init_cipher_switching 8.34 note A note A 16 mm_ft_init_cipher_switching 8.33 note A note A 17 mm_zap_increment 8.26 note A note A 18 mm_dck_storing 8.27 note A m 19 mm_dck_sending - i i 20 mm_service_class_mgt 8.30, 8.24 note A note A 21 mm_partial_release 8.39 m m 22 mm_timer_f_mm_ident_1_mgt 8.28.1.2 note A note A 23 mm_timer_f_mm_access_2_mgt 8.31.1.1 note A note A 24 mm_timer_f_mm_auth_1_mgt 8.32.1.2 note A note A 25 mm_timer_f_mm_cipher_1_mgt 8.33.1.1 note A note A 26 mm_timer_f_mm_key_1_mgt 8.32.2.1 note A note A 27 mm_timer_f_mm_ident.2_mgt 8.28 note A note A 28 mm_timer_f_mm_auth_2_mgt 8.25.1.1 note A note A 29 mm_modify_access_rights - i i c.a801: IF A.4/11 THEN o ELSE i.
Table A.9: Profile modification for EN 300 476-4 [3] table A.20 SS protocols supported Item SS protocol name Profile reference Profile status R/B Profile status P 1 crss_keypad_protocol 8.10 m m 2 crss_feature_key_mgt_protocol - i i 3 crss_functional_protocol_smc - i i 4 ciss_keypad_protocol - i i 5 ciss_feature_key_mgt_protocol - i i 6 ciss_partial_release - i i 7 crss_functional_protocol_ciec - i i 8 ciss_functional_protocol_ciec - i i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 15 Table A.10: Profile modification for EN 300 476-4 [3] table A.23 LCE procedures supported Item LCE procedures Profile reference Profile status R/B Profile status P 1 lce_direct_pt_init_link_establishment 8.36 m m 2 lce_indirect_ft_init_link_establishment 8.35 m m 3 lce_direct_ft_init_link_establishment - i i 4 lce_link_maintenance 8.39 m m 5 lce_link_suspend - i i 6 lce_link_resume - i i 7 lce_link_release 8.37, 8.38 m m 8 lce_link_partial_release 8.39 m m 9 lce_cl_message_routing - i i 10 lce_cl_broadcast_announce - i i 11 lce_timer_lce_01_mgt 8.37.1.1 m m 12 lce_timer_lce_02_mgt 8.39.1.1 m m 13 lce_timer_lce_03_mgt 8.35.1.1 m m 14 lce_timer_lce_04_mgt - i i 15 lce_timer_lce_05_mgt 8.36 m m
Table A.11: Profile modification for EN 300 476-4 [3] table A.24 LLME procedures supported Item LLME procedures Profile reference Profile status R/B Profile status P 1 mgt_prioritized_list_negotiation - i i 2 mgt_exchanged_attribute_negotiation - i i 3 mgt_operating_parameter_negotiation - i i 4 mgt_service_modification - i i 5 mgt_mm_procedures_prioriry_mgt 13.1 m m 6 mgt_mm_cc_coexistance 6.9.6 m m 7 mgt_mm_coms_coexistance - i i 9 mgt_external_handover - i i 10 mgt_test_call_back - i i 11 mgt_test_hook_control - i i 12 mgt_upper_tester - i i
A.2.2 Messages To express the profile requirements of EN 300 444 [2], the following tables indicate the change of status for support of NWK layer messages. A.2.2.1 Call control messages Table A.12: Profile modification for EN 300 476-4 [3] table A.25 CC receiving (P to F) messages supported Item CC receiving (P to F) Message name Profile reference Profile status R/B/P 1 CC-SETUP 8.2 m 2 CC-INFOrmation 8.10 m 5 CC-ALERTING 8.13 m 6 CC-CONNECT 8.15 m 8 CC-RELEASE 8.7, 8.8 m 9 CC-RELEASE-COMplete 8.7, 8.9 m 14 IWU-INFOrmation - i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 16 Table A.13: Profile modification for EN 300 476-4 [3] table A.26 CC sending (F to P) messages supported Item CC sending (F to P) Message name Profile reference Profile status R/B/P 1 CC-SETUP 8.12 m 2 CC-INFOrmation 8.16 note A 3 CC-SETUP-ACKnowledge 8.3 o 4 CC-CALL-PROCeeding 8.4 o 5 CC-ALERTING 8.5 o 6 CC-CONNECT 8.6 m 7 CC-CONNECT-ACKnowledge 8.15 m 8 CC-RELEASE 8.7, 8.9 m 9 CC-RELEASE-COMplete 8.7, 8.8 m 13 CC-NOTIFY 6.9.6 o 14 IWU-INFOrmation - i
Table A.14: Profile modification for EN 300 476-4 [3] table A.27 CC-SETUP receiving (P to F) supported Item CC-SETUP receiving (P to F) Information element name Profile reference Profile status R/B/P 6 IWU attributes - i 7 Repeat indicator "prioritized list" - i 8 Call attributes 1 - i 9 Call attributes 2 - i 10 Call attributes 3 - i 11 Repeat indicator "non-prioritized list" - i 12 Connection attributes 1 - i 13 Connection attributes 2 - i 14 Connection attributes 3 - i 15 Cipher info - i 16 Connection identity - i 17 Facility - i 20 Keypad - i 22 Feature Activate - i 24 Network parameter - i 26 Terminal capability - i 27 End-to-end compatibility - i 28 Rate parameters - i 29 Transit delay - i 30 Window size - i 31 Calling party number - i 32 Called party number - i 33 Called party subaddress - i 34 Sending complete - i 35 IWU-to-IWU - i 36 IWU-PACKET - i 37 Escape to proprietary - i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 17 Table A.15: Profile modification for EN 300 476-4 [3] table A.28 CC-SETUP sending (F to P) supported Item CC-SETUP sending (F to P) Information element name Profile reference Profile status R/B/P 6 IWU attributes - i 7 Repeat indicator "prioritized list" - i 8 Call attributes 1 - i 9 Call attributes 2 - i 10 Call attributes 3 - i 11 Repeat indicator "prioritized list" - i 12 Connection attributes 1 - i 13 Connection attributes 2 - i 14 Connection attributes 3 - i 15 Cipher info - i 16 Connection identity - i 17 Facility - i 18 Progress Indicator - i 19 Display 8.16 note A 21 Signal 8.14 note A 23 Feature Indicate - i 27 End-to-end compatibility - i 28 Rate parameters - i 29 Transit delay - i 30 Window size - i 31 Calling party number 8.12 c.a1501 32 Called party number - i 33 Called party subaddress - i 34 Sending complete - i 35 IWU-to-IWU - i 36 IWU-PACKET - i 37 Escape to proprietary - i c.a1501: IF feature N30 (CLIP) implemented THEN m ELSE i.
Table A.16: Profile modification for EN 300 476-4 [3] table A.29 CC-INFO receiving (P to F) supported Item CC-INFO receiving (P to F) Information element name Profile reference Profile status R/B/P 2 Location area - i 3 NWK assigned identity - i 4 Facility - i 7 Keypad 8.10 m 9 Feature activate - i 11 Network parameter - i 13 Calling party number - i 14 Called party number - i 15 Called party subaddress - i 16 Sending complete - i 18 IWU-to-IWU - i 19 IWU-packet - i 20 Escape to proprietary - i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 18 Table A.17: Profile modification for EN 300 476-4 [3] table A.30 CC-INFO sending (F to P) supported Item CC-INFO sending (F to P) Information element name Profile reference Profile status R/B/P 4 Facility - i 5 Progress Indicator - i 6 Display 8.16 note A 8 Signal 8.14 note A 10 Feature indicate - i 13 Calling party number - i 14 Called party number - i 15 Called party subaddress - i 16 Sending complete - i 17 Test hook control - i 18 IWU-to-IWU - i 19 IWU-packet - i 20 Escape to proprietary - i
Table A.18: Profile modification for EN 300 476-4 [3] table A.31 CC-SETUP-ACK sending (F to P) supported Item CC-SETUP-ACK sending (F to P) Information element name Profile reference Profile status R/B/P 2 Info type - i 3 Portable identity - i 4 Fixed identity - i 5 Location area - i 6 IWU attributes - i 7 Call attributes - i 8 Connection attributes - i 9 Connection identity - i 10 Facility - i 11 Progress indicator 8.3.1 o 12 Display 8.16 note A 13 Signal - i 14 Feature indicate - i 17 Transit delay - i 18 Window size - i 19 Delimiter request - i 20 IWU-TO-IWU - i 21 IWU-PACKET - i 22 Escape to proprietary - i
ETSI ETSI EN 300 474-2 V1.2.1 (2003-09) 19 Table A.19: Profile modification for EN 300 476-4 [3] table A.32 CC-CALL-PROC sending (F to P) supported Item CC-CALL-PROC sending (F to P) Information element name Profile reference Profile status R/B/P 2 IWU attributes - i 3 Call attributes - i 4 Connection attributes - i 5 Connection identity - i 6 Facility - i 7 Progress indicator 8.4.1 o 8 Display 8.16 note A 9 Signal - i 10 Feature indicate - i 11 Transit delay - i 12 Window size - i 13 IWU-to-IWU - i 14 IWU-PACKET - i 15 Escape to proprietary - i
Table A.20:
...