SIST EN 61300-2-48:2009
(Main)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-48: Tests - Temperature-humidity cycling (IEC 61300-2-48:2009)
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-48: Tests - Temperature-humidity cycling (IEC 61300-2-48:2009)
IEC 61300-2-48:2009(E) details a procedure for determining the suitability of a fibre optic device or closure to withstand variations in humidity and temperature that may occur during operation, storage and/or transport. The test is intended to indicate the performance of such devices when exposed to heat and humidity followed by short-term freezing. The main changes to this second edition are the addition of the Category O cycle procedure and the severity reconsideration.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-48: Prüfungen - Temperatur-Feuchte-Zyklus (IEC 61300-2-48:2009)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes fondamentales d'essais et de mesures - Partie 2-48: Essais - Cycles d'humidité et de température (CEI 61300-2-48:2009)
IEC 61300-2-48:2009 précise une méthode pour déterminer l’aptitude d’un dispositif ou d’une terminaison à fibres optiques à résister aux variations d’humidité et de température susceptibles de se produire pendant le fonctionnement, le stockage et/ou le transport. L’essai est destiné à indiquer la performance de tels dispositifs lorsqu’ils sont exposés à la chaleur et à l’humidité suivies par une congélation de courte durée. En termes généraux, cet essai fournit une température élevée qui induit des défaillances potentielles du fait du ramollissement et de la dilatation, une humidité élevée pour favoriser l’absorption d’humidité et le gonflement, et une basse température pour faciliter la formation de glace, la fragilisation et la contraction. Cet essai diffère des autres essais d’environnement cycliques, en particulier l’essai de chaleur humide cyclique de l’IEC 61300-2-46 et l’essai cyclique composite de température et d’humidité de l’IEC 61300-2-21, par l’incorporation des niveaux alternatifs de sévérité. A cet effet:
a) le nombre de cycles est augmenté;
b) la plage de températures cycliques est élargie;
c) la période cyclique est réduite.
Cette seconde édition de l’IEC 61300-2-48 annule et remplace la première édition publiée en 2003, dont elle constitue une révision technique. L’ajout de la procédure de cycle de catégorie O et le réexamen de la sévérité constituent les principaux changements.
La présente version bilingue (2020-08) correspond à la version anglaise monolingue publiée en 2009-03.
Povezovalne naprave in pasivne komponente optičnih vlaken - Postopki osnovnega preskušanja in merjenja - 2-48. del: Preskusi - Temperaturni cikli in cikli vlažnosti (IEC 61300-2-48:2009)
General Information
- Status
- Published
- Publication Date
- 20-May-2009
- Technical Committee
- iTEL - Communication cables
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 11-May-2009
- Due Date
- 16-Jul-2009
- Completion Date
- 21-May-2009
Relations
- Effective Date
- 01-Jul-2009
Overview
EN 61300-2-48:2009 (IEC 61300-2-48:2009) defines a standardized temperature-humidity cycling test for fibre optic interconnecting devices and passive components. The procedure assesses a device or closure’s ability to withstand variations in humidity and temperature encountered during operation, storage and transport - specifically exposure to heat and humidity followed by short-term freezing. This second edition (2009) supersedes the 2003 edition and adds the Category O cycle and a reconsideration of test severity.
Key topics and technical requirements
- Scope and purpose: Determine suitability against moisture-related swelling, softening/expansion at high temperature and embrittlement/ice formation at low temperature.
- Test methods: Two conditioning approaches are specified:
- Method A (Category O option): 14 cycles between Tmax and Tmin with rapid transitions to maximize condensation; dwell times minimum 2 h; controlled 95% RH at 23 °C and at Tmax; temperature transition limits specified (e.g., 20 min max for Tmin↔Tmax segments).
- Method B: 42 cycles between Tmax and −40 °C; temperature rate ≥ 1 °C/min; dwell times minimum 1 h; humidity controlled from 10 °C to Tmax.
- Apparatus: Environmental chamber capable of homogeneous temperature/humidity control; use distilled/demineralized water; prevent condensed water dripping and avoid rust/corrosion contamination.
- Measurements: Continuous attenuation monitoring (optical source and detector per IEC 61300-3-4) with initial and final examinations per IEC 61300-1 and IEC 61300-3-1/3-4.
- Preconditioning: 2 h at standard test conditions (IEC 61300-1) before cycling.
- Severity provisions: Alternative severity levels achieved via number of cycles, cyclic temperature range and cycle period; tolerances on RH (±5 %) and temperature (±2 °C) are provided.
Applications and who uses it
- Manufacturers of fibre optic connectors, closures, splice enclosures and passive components - for design validation and product qualification.
- Test laboratories and quality assurance teams - to verify environmental robustness and record attenuation over time.
- OEMs and system integrators - to specify acceptance criteria for components intended for harsh or variable climatic conditions.
- Procurement and standards compliance - to reference a harmonized EN/IEC test for contracts or regulatory conformity.
Relevant keywords for search: EN 61300-2-48:2009, temperature-humidity cycling, fibre optic interconnecting devices, attenuation monitoring, environmental chamber, Category O cycle, IEC 61300.
Related standards
- EN/IEC 61300-1 (General and guidance)
- EN/IEC 61300-3-1 (Visual examination)
- EN/IEC 61300-3-4 (Attenuation measurement)
- Related cyclic tests: IEC 61300-2-46 (damp heat cyclic) and IEC 61300-2-21 (composite temperature-humidity cyclic) - this standard is differentiated by its higher severity options.
Frequently Asked Questions
SIST EN 61300-2-48:2009 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-48: Tests - Temperature-humidity cycling (IEC 61300-2-48:2009)". This standard covers: IEC 61300-2-48:2009(E) details a procedure for determining the suitability of a fibre optic device or closure to withstand variations in humidity and temperature that may occur during operation, storage and/or transport. The test is intended to indicate the performance of such devices when exposed to heat and humidity followed by short-term freezing. The main changes to this second edition are the addition of the Category O cycle procedure and the severity reconsideration.
IEC 61300-2-48:2009(E) details a procedure for determining the suitability of a fibre optic device or closure to withstand variations in humidity and temperature that may occur during operation, storage and/or transport. The test is intended to indicate the performance of such devices when exposed to heat and humidity followed by short-term freezing. The main changes to this second edition are the addition of the Category O cycle procedure and the severity reconsideration.
SIST EN 61300-2-48:2009 is classified under the following ICS (International Classification for Standards) categories: 33.180.20 - Fibre optic interconnecting devices. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 61300-2-48:2009 has the following relationships with other standards: It is inter standard links to SIST EN 61300-2-48:2004. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 61300-2-48:2009 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SNLLichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-48: Prüfungen - Temperatur-Feuchte-Zyklus (IEC 61300-2-48:2009)Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes fondamentales d'essais et de mesures - Partie 2-48: Essais - Cycles d'humidité et de température (CEI 61300-2-48:2009)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-48: Tests - Temperature-humidity cycling (IEC 61300-2-48:2009)33.180.20Fibre optic interconnecting devicesICS:Ta slovenski standard je istoveten z:EN 61300-2-48:2009SIST EN 61300-2-48:2009en01-julij-2009SIST EN 61300-2-48:2009SLOVENSKI
STANDARDSIST EN 61300-2-48:20041DGRPHãþD
EUROPEAN STANDARD EN 61300-2-48 NORME EUROPÉENNE
EUROPÄISCHE NORM May 2009
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-2-48:2009 E
ICS 33.180.20 Supersedes EN 61300-2-48:2003
English version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-48: Tests -
Temperature-humidity cycling (IEC 61300-2-48:2009)
Dispositifs d'interconnexion
et composants passifs à fibres optiques - Méthodes fondamentales d'essais
et de mesures -
Partie 2-48: Essais -
Cycles d'humidité et de température (CEI 61300-2-48:2009)
Lichtwellenleiter -
Verbindungselemente
und passive Bauteile -
Grundlegende Prüf- und Messverfahren - Teil 2-48: Prüfungen -
Temperatur-Feuchte-Zyklus (IEC 61300-2-48:2009)
This European Standard was approved by CENELEC on 2009-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
– 2 – Foreword The text of document 86B/2807/FDIS, future edition 2 of IEC 61300-2-48, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-2-48 on 2009-04-01. This European Standard supersedes EN 61300-2-48:2003. The main changes are the addition of the Category O cycle procedure and the severity reconsideration. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop) 2010-01-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow) 2010-04-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 61300-2-48:2009 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61300-2-21 NOTE
Harmonized as EN 61300-2-21:1997 (not modified). IEC 61300-2-46 NOTE
Harmonized as EN 61300-2-46:2006 (not modified). __________ SIST EN 61300-2-48:2009
– 3 – EN 61300-2-48:2009
Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 61300-1 - 1) Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -
Part 1: General and guidance EN 61300-1 2003 2)
IEC 61300-3-1 - 1) Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -
Part 3-1: Examinations and measurements - Visual examination EN 61300-3-1 2005 2)
IEC 61300-3-4 - 1) Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -
Part 3-4: Examinations and measurements - Attenuation EN 61300-3-4 2001 2)
1) Undated reference.
2) Valid edition at date of issue.
IEC 61300-2-48Edition 2.0 2009-03INTERNATIONAL STANDARD
Fibre optic interconnecting devices and passive components – Basic test and measurement procedures –
Part 2-48: Tests – Temperature-humidity cycling
INTERNATIONAL ELECTROTECHNICAL COMMISSION KICS 33.180.20 PRICE CODEISBN 2-8318-1033-6
– 2 – 61300-2-48 © IEC:2009(E) CONTENTS FOREWORD.3 1 Scope.5 2 Normative references.5 3 General description.5 4 Apparatus.6 4.1 Chamber.6 4.2 Optical source and detector.6 5 Procedure.6 5.1 Preparation of specimens.6 5.2 Preconditioning.6 5.3 Initial examinations and measurements.6 5.4 Conditioning.6 5.4.1 Method A.6 5.4.2 Method B.7 5.5 Recovery.8 5.6 Final examinations and measurements.8 6 Severity.9 7 Details to be specified.9 Bibliography.10
Figure 1 – Temperature-humidity profile for Tmax = 65 °C, Tmin = −10 °C.7 Figure 2 – Temperature-humidity profile for Tmax = 85 °C.8
Table 1 – Test severities.9
61300-2-48 © IEC:2009(E) – 3 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –
Part 2-48: Tests – Temperature-humidity cycling
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...