SIST EN 50632-2-17:2016

SLOVENSKI STANDARD
SIST EN 50632-2-17:2016
01-oktober-2016
Elektromotorna orodja - Postopek merjenja prahu - 2-17. del: Posebne zahteve za
rezkalnike in obrezovalnike
Electric motor-operated tools - Dust measurement procedure - Part 2-17: Particular
requirements for routers and trimmers
Ta slovenski standard je istoveten z: EN 50632-2-17:2016
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 50632-2-17:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50632-2-17:2016

---------------------- Page: 2 ----------------------

SIST EN 50632-2-17:2016

EUROPEAN STANDARD EN 50632-2-17

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2016
ICS 13.040.40; 25.140.20; 65.060.80
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-17: Particular requirements for routers and trimmers
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-17: Exigences particulières pour les Teil 2-17: Besondere Anforderungen für Oberfräsen und
défonceuses Kantenfräsen
This European Standard was approved by CENELEC on 2016-05-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 50632-2-17:2016 E

---------------------- Page: 3 ----------------------

SIST EN 50632-2-17:2016
EN 50632-2-17:2016 (E)
Contents
European foreword . 3
1 Scope . 4
2 Normative references. 4
3 Terms and definitions . 4
4 Test procedure . 4
5 Instrumentation . 5
6 Information to be reported . 6
Tables
Table 101 – Operating conditions for routers intended for cutting wood . 5
Table 102 — Operating conditions for trimmers intended for cutting wood . 5
2

---------------------- Page: 4 ----------------------

SIST EN 50632-2-17:2016
EN 50632-2-17:2016 (E)
European foreword
This document (EN 50632-2-17:2016) has been prepared by CLC/TC 116 "Safety of motor-operated
electric tools".
The following dates are fixed:
(dop) 2017-05-03
• latest date by which this document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-05-03
• latest date by which the national
standards conflicting with this
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying
any or all such patent rights.
This European Standard is divided into three parts:
Part 1: General requirements for the dust measurement which are common to electric motor-operated
tools (for the purpose of this standard referred to simply as tools);
Part 2 or 3: Requirements for the dust measurement for particular types of tools, which either
supplement or modify the requirements given in Part 1 to account for the particular
characteristics of these spec
...