SIST EN ISO 12945-1:2001

SLOVENSKI STANDARD
SIST EN ISO 12945-1:2001
01-september-2001
Tekstilije - Ugotavljanje nagnjenja tekstilij k površinskemu razvlaknjanju in pilingu
- 1. del: Metoda piling posode (ISO 12945-1:2000)
Textiles - Determination of fabric propensity to surface fuzzing and to pilling - Part 1:
Pilling box method (ISO 12945-1:2000)
Textilien - Bestimmung der Neigung von textilen Flächengebilden zur Flusenbildung auf
der Oberfläche und der Pillbildung - Teil 1: Verfahren mit dem Pilling-Prüfkasten (ISO

12945-1:2000)
Textiles - Détermination de la propension des étoffes a l'ébouriffage en surface et au
boulochage - Partie 1: Méthode de la boîte de boulochage (ISO 12945-1:2000)
Ta slovenski standard je istoveten z: EN ISO 12945-1:2000
ICS:
59.080.30 Tkanine Textile fabrics
SIST EN ISO 12945-1:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12945-1:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 12945-1:2001
EUROPEAN STANDARD
EN ISO 12945-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2000
ICS 59.080; 59.080.30
English version
Textiles - Determination of fabric propensity to surface fuzzing
and to pilling - Part 1: Pilling box method (ISO 12945-1:2000)
Textiles - Détermination de la propension des étoffes à Textilien - Bestimmung der Neigung von textilen
l'ébouriffage en surface et au boulochage - Partie 1: Flächengebilden zur Flusenbildung auf der Oberfläche und
Méthode de la boîte de boulochage (ISO 12945-1:2000) der Pillbildung - Teil 1: Verfahren mit dem Pilling-
Prüfkasten (ISO 12945-1:2000)
This European Standard was approved by CEN on 10 December 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12945-1:2000 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12945-1:2001
Page 2
EN ISO 12945-1:2000
CORRECTED 2001-04-11
Foreword
The text of the International Standard ISO 12945-1:2000 has been prepared by Technical
Committee ISO/TC 38 "Plastics" in collaboration with Technical Committee CEN/TC 248
"Plastics", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2001, and conflicting national
standards shall be withdrawn at the latest by June 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 12945-1:2000 was approved by CEN as a
European Standard without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).

---------------------- Page: 4 ----------------------

SIST EN ISO 12945-1:2001
Page 3
EN ISO 12945-1:2000
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 139 1973 Textiles - Standard atmospheres for EN 20139 1992
conditioning and testing

---------------------- Page: 5 ----------------------

SIST EN ISO 12945-1:2001

---------------------- Page: 6 ----------------------

SIST EN ISO 12945-1:2001
INTERNATIONAL ISO
STANDARD 12945-1
First edition
2000-12-15
Textiles — Determination of fabric
propensity to surface fuzzing and to
pilling —
Part 1:
Pilling box method
Textiles — Détermination de la propension des étoffes à l'ébouriffage en
surfaceetauboulochage—
Partie 1: Méthode de la boîte de boulochage
Reference number
ISO 12945-1:2000(E)
©
ISO 2000

---------------------- Page: 7 ----------------------

SIST EN ISO 12945-1:2001
ISO 12945-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 12945-1:2001
ISO 12945-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 12945 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 12945-1 was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee
SC 24, Conditioning atmospheres and physical tests for textile fabrics.
ISO 12945 consists of the following parts, under the general title Textiles — Determination of fabric propensity to
surface fuzzing and to pilling:
� Part 1: Pilling box method
� Part 2: Modified Martindale method
� Part 3: Determination using a random tumble method
Annex A of this part of ISO 12945 is for information only.
© ISO 2000 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 12945-1:2001
ISO 12945-1:2000(E)
Introduction
Pills are formed when fibres on a fabric surface “tease out” and become entangled during wear. Such surface
deterioration is generally undesirable, but the degree of consumer tolerance for a given level of pilling will depend
on the garment type and fabric end use.
Generally the level of pilling which develops is determined by the rates of the following parallel processes:
a) fibre entanglement leading to pill formation;
b) development of more surface fibre;
c) fibre and pill wear-off.
The rates of these processes depend on the fibre, yarn and fabric properties. Examples of extreme situations are
found in fabrics containing strong fibres versus fabric containing weak fibres. A consequence of the strong fibre is a
rate of pill formation that exceeds the rate of wear-off. This results in an increase of pilling with an increase of wear.
With a weak fibre the rate of pill formation competes with the rate of wear-off. This would result in a fluctuation of
pilling with an increase of wear. There are other constructions in which the surface fibre wear-off occurs before pill
formation. Each of these examples demonstrates the complexity of evaluating the surface change on different
types of fabric.
The ideal laboratory test would accelerate the wear processes a), b) and c) by exactly the same factor and would
be universally applicable to all fibre, yarn and fabric types. No such test has been developed. However, a test
procedure has been established in which fabrics can be ranked in the same order of fuzzing and pilling propensity
as is likely to occur in end-use wear.
Particular attention is drawn to annex A which gives advice on the maintenance of the apparatus. It is
recommended that annex A be studied prior to carrying out the procedure.
iv © ISO 2000 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 12945-1:2001
INTERNATIONAL STANDARD ISO 12945-1:2000(E)
Textiles — Determination of fabric propensity to surface fuzzing
and to pilling —
Part 1:
Pilling box method
1 Scope
This part of ISO 12945 describes a method for the determination of the resistance to pilling and surface change of
textile fabrics.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this part of ISO 12945. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 12945 are encouraged to investigate the
possibility of applying the most recent edition of the normative document indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 139, Textiles — Standard atmospheres for conditioning and testing.
3 Terms and definitions
For the purposes of this part of ISO 12945, the following terms and definitions apply.
3.1
fuzzing
roughing up of the surface fibres an
...