SIST EN IEC 60136:2024
(Main)Dimensions, marking and testing of carbon brushes and dimensions of brush-holders for electrical machinery (IEC 60136:2024)
Dimensions, marking and testing of carbon brushes and dimensions of brush-holders for electrical machinery (IEC 60136:2024)
IEC 60136:2024 applies primarily to brushes and brush-holders for cylindrical commutators and slip rings for electrical rotating machines. Some clauses of this document may cover other configurations, such as flat commutators or plain disks. It defines the dimensions of brushes and their components, together with their tolerances:
- dimensions of brush block (t, a, r),
- angles α and β,
- chamfer,
- flexibles (shunts),
- standard terminals.
It also covers the conventional designation of principal dimensions, the marking of brushes and the testing methods for the qualification of brushes after their manufacturing (except the brush grade material, covered by IEC 60413). This third edition cancels and replaces the second edition published in 1986 and Amendment 1:1995. This edition constitutes a technical revision.
Please refer to the Foreword of the document for a comprehensive listing of the changes with respect to the previous edition.
Abmessungen, Kennzeichnung und Prüfung von Kohlebürsten und Abmessungen von Bürstenhaltern für elektrische Maschinen (IEC 60136:2024)
Dimensions, marquages et essais des balais et dimensions des porte-balais pour machines électriques (IEC 60136:2024)
IEC 60136:2024 s'applique principalement aux balais et aux porte-balais montés sur collecteurs cylindriques et bagues des machines électriques tournantes. Certains articles du présent document peuvent couvrir d'autres configurations, comme les collecteurs plats ou les disques lisses. Il définit les dimensions des balais et de leurs composants, ainsi que leurs tolérances:
- dimensions du bloc de balai (t, a, r);
- angles α et β;
- chanfrein;
- câbles (shunts);
- cosses normalisées.
Il couvre également la désignation conventionnelle des dimensions principales, le marquage des balais et les méthodes d'essai pour la qualification des balais après leur fabrication (à l'exception du matériau de la nuance des balais, couvert par l'IEC 60413). Cette troisième édition annule et remplace la deuxième édition parue en 1986 et l'Amendement 1:1995. Cette édition constitue une révision technique.
Veuillez vous référer à l'avant-propos du document pour une liste complète des modifications par rapport à l'édition précédente.
Mere, označevanje in preskušanje grafitnih ščetk ter mere držal ščetk za električne stroje (IEC 60136:2024)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 60136:2022
01-oktober-2022
Mere, označevanje in preskušanje ogljikovih ščetk ter mere držal ščetk za
električne stroje
Dimensions, marking and testing of carbon brushes and dimensions of brush-holders for
electrical machinery
Dimensions des balais et porte-balais pour machines électriques
Ta slovenski standard je istoveten z: prEN IEC 60136:2022
ICS:
29.160.10 Sestavni deli rotacijskih Components for rotating
strojev machines
oSIST prEN IEC 60136:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN IEC 60136:2022
---------------------- Page: 2 ----------------------
oSIST prEN IEC 60136:2022
2/2103/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60136 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2022-08-19 2022-11-11
SUPERSEDES DOCUMENTS:
2/2077/CD, 2/2092A/CC
IEC TC 2 : ROTATING MACHINERY
SECRETARIAT: SECRETARY:
United Kingdom Mr Charles Whitlock
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if any, in
this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for Vote
(CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
TITLE:
Dimensions, marking and testing of carbon brushes and dimensions of brush-holders for electrical machinery
PROPOSED STABILITY DATE: 2025
NOTE FROM TC/SC OFFICERS:
Copyright © 2022 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 60136:2022
– 2 – IEC CDV 60136 IEC 2022
CONTENTS
FOREWORD . 7
1 Scope . 9
2 Normative references . 9
3 Terms, definitions and symbols . 9
3.1 Terms and definitions. 9
3.2 Symbols . 17
4 Units and marking. 19
4.1 Units . 19
4.2 Marking . 19
4.2.1 Units . 19
4.2.2 Additional marks on the brush . 20
4.2.3 Additional marks for brush-holders . 20
5 Principal dimensions and tolerances of brushes . 21
5.1 Sequence . 21
5.2 Standard dimensions . 22
5.3 Tolerances on principal dimensions . 22
5.3.1 General tolerances . 22
5.3.2 Split brushes . 23
5.3.3 Metal-graphite brushes .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.