SIST EN 300 113-1 V1.5.1:2003

SLOVENSKI STANDARD
SIST EN 300 113-1 V1.5.1:2003
01-december-2003
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP(50±
6WRULWHYNRSHQVNLKPRELOQLKNRPXQLNDFLM±5DGLMVNDRSUHPD]DSUHQRVSRGDWNRY
R]LURPDJRYRUDNLXSRUDEOMDPRGXODFLMRVNRQVWDQWQRDOLQHNRQVWDQWQRRYRMQLFR
LQLPDDQWHQVNLSULNOMXþHN±GHO7HKQLþQHNDUDNWHULVWLNHLQPHULOQHPHWRGH
Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service;
Radio equipment intended for the transmission of data (and/or speech) using constant or
non-constant envelope modulation and having an antenna connector; Part 1: Technical
characteristics and methods of measurement
Ta slovenski standard je istoveten z: EN 300 113-1 Version 1.5.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 300 113-1 V1.5.1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 300 113-1 V1.5.1:2003

---------------------- Page: 2 ----------------------

SIST EN 300 113-1 V1.5.1:2003

ETSI EN 300 113-1 V1.5.1 (2003-09)
European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land mobile service;
Radio equipment intended for the transmission
of data (and/or speech) using constant or non-constant
envelope modulation and having an antenna connector;
Part 1: Technical characteristics and
methods of measurement

---------------------- Page: 3 ----------------------

SIST EN 300 113-1 V1.5.1:2003
 2 ETSI EN 300 113-1 V1.5.1 (2003-09)



Reference
REN/ERM-TG32-046-1
Keywords
antenna, data, mobile, radio, speech, PMR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, send your comment to:
editor@etsi.org
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2003.
All rights reserved.

TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 300 113-1 V1.5.1:2003
 3 ETSI EN 300 113-1 V1.5.1 (2003-09)
Contents
Intellectual Property Rights.8
Foreword.8
Introduction .8
1 Scope.10
2 References.11
3 Definitions, symbols and abbreviations .12
3.1 Definitions.12
3.2 Symbols.13
3.3 Abbreviations.13
4 General.14
4.1 Selection of equipment for testing purposes.15
4.2 Mechanical and electrical design.15
4.2.1 General.15
4.2.2 Controls.15
4.2.3 Transmitter shut-off facility.15
4.2.4 Marking.15
4.3 Interpretation of the measurement results .15
4.4 Testing using bit streams or messages.16
4.5 Measuring continuous mode equipment.16
4.6 Measuring discontinuous mode equipment .16
5 Technical characteristics.16
5.1 Transmitter parameter limits .16
5.1.1 Frequency error.16
5.1.2 Carrier power (conducted) .17
5.1.3 Effective radiated power.17
5.1.4 Adjacent channel power.18
5.1.5 Spurious emissions.18
5.1.6 Intermodulation attenuation.19
5.1.7 Transmitter attack time .19
5.1.8 Transmitter release time.19
5.1.9 Transient behaviour of the transmitter .19
5.1.9.1 Time domain analysis of power and frequency.19
5.1.9.2 Adjacent channel transient power .20
5.1.9.2.1 Equipment measured as constant envelope angle modulation equipment .20
5.1.9.2.2 Equipment measured as non-constant envelope modulation equipment .20
5.2 Receiver parameter limits.21
5.2.1 Maximum usable sensitivity (data or messages, conducted) .21
5.2.2 Average usable sensitivity (data or messages, field strength).21
5.2.3 Error behaviour at high input levels.21
5.2.4 Co-channel rejection.21
5.2.5 Adjacent channel selectivity .21
5.2.6 Spurious response rejection .22
5.2.7 Intermodulation response rejection.22
5.2.8 Blocking or desensitization.22
5.2.9 Spurious radiations.22
5.3 Duplex operation - receiver limits.23
5.3.1 Receiver desensitization and maximum usable sensitivity (with simultaneous transmission and
reception) .23
5.3.2 Receiver spurious response rejection (with simultaneous transmission and reception).23
6 Test conditions, power sources and ambient temperatures .23
6.1 Normal and extreme test conditions .23
6.2 Test power source.23
ETSI

---------------------- Page: 5 ----------------------

SIST EN 300 113-1 V1.5.1:2003
 4 ETSI EN 300 113-1 V1.5.1 (2003-09)
6.3 Normal test conditions.23
6.3.1 Normal temperature and humidity.23
6.3.2 Normal test power source .24
6.3.2.1 Mains voltage.24
6.3.2.2 Regulated lead-acid battery power sources used on vehicles.24
6.3.2.3 Other power sources.24
6.4 Extreme test conditions .24
6.4.1 Extreme temperatures.24
6.4.2 Extreme test source voltages.24
6.4.2.1 Mains voltage.24
6.4.2.2 Regulated lead-acid battery power sources on vehicles .24
6.4.2.3 Power sources using other types of batteries.25
6.4.2.4 Other power sources.25
6.5 Procedure for tests at extreme temperatures.25
6.5.1 Procedure for equipment designed for continuous operation.25
6.5.2 Procedure for equipment designed for intermittent operation .26
7 General conditions.26
7.1 Arrangements for test signals applied to the receiver input.26
7.2 Receiver mute or squelch facility.26
7.3 Normal test signals (wanted and unwanted signals).26
7.3.1 Equipment measured as constant envelope angle modulation equipment .26
7.3.2 Equipment measured as non-constant envelope modulation equipment.27
7.4 Encoder for receiver measurements .28
7.5 Transceiver data interface.28
7.6 Impedance.28
7.7 Artificial antenna.28
7.8 Tests of equipment with a duplex filter .28
7.9 Facilities for access .28
7.9.1 Analogue access.28
7.9.2 Test points for bit stream measurements.29
7.9.3 Coupling arrangements.29
7.9.3.1 Arrangements for measurements with continuous bit streams.29
7.9.3.2 Arrangements for measurements with messages.29
7.10 Test site and general arrangements for measurements involving the use of radiated fields .29
7.11 Modes of operation of the transmitter .30
8 Methods of measurement for transmitter parameters.30
8.1 Frequency error.30
8.1.1 Definition.30
8.1.2 Method of measurement.30
8.2 Carrier power (conducted).31
8.2.1 Definitions.31
8.2.1.1 Equipment measured as constant envelope angle modulation equipment.31
8.2.1.2 Equipment measured as non-constant envelope modulation equipment.31
8.2.2 Method of measurement.31
8.2.2.1 Equipment measured as constant envelope angle modulation equipment.31
8.2.2.2 Equipment measured as non-constant envelope modulation equipment.32
8.3 Effective radiated power (field strength).32
8.3.1 Definition.32
8.3.1.1 Equipment measured as constant envelope angle modulation equipment.32
8.3.1.2 Equipment measured as non-constant envelope modulation equipment.32
8.3.2 Methods of measurement.33
8.3.2.1 Equipment measured as constant envelope angle modulation equipment.34
8.3.2.2 Equipment measured as non-constant envelope modulation equipment.35
8.4 Maximum permissible frequency deviation .36
8.4.1 Definition.36
8.4.2 Method of measurement.36
8.5 Adjacent channel power .37
8.5.1 Definition.37
8.5.2 Method of measurement.37
8.6 Spurious emissions.38
ETSI

---------------------- Page: 6 ----------------------

SIST EN 300 113-1 V1.5.1:2003
 5 ETSI EN 300 113-1 V1.5.1 (2003-09)
8.6.1 Definition.38
8.6.2 Method of measuring the power level .39
8.6.2.1 Equipment measured as constant envelope angle modulation equipment.39
8.6.2.2 Equipment measured as non-constant envelope modulation equipment.39
8.6.3 Method of measuring the effective radiated power.40
8.6.3.1 Equipment measured as constant envelope angle modulation equipment.40
8.6.3.2 Equipment measured as non-constant envelope modulation equipment.41
8.7 Intermodulation attenuation.42
8.7.1 Definition.42
8.7.2 Method of measurement.43
8.8 Transmitter attack time.43
8.8.1 Definition.44
8.8.2 Method of measurement.44
8.9 Transmitter release time .45
8.9.1 Definition.45
8.9.2 Method of measurement.45
8.10 Transient behaviour of the transmitter.45
8.10.1 Definitions.46
8.10.2 Timings, frequencies and powers .47
8.10.3 Methods of measurement.51
8.10.3.1 Time domain measurements of power and frequency.51
8.10.3.2 Test arrangement and characteristics of the FM modulation meter .52
8.10.3.3 Adjacent channel transient power measurements.52
8.10.3.3.1 Definition.52
8.10.3.3.2 Equipment measured as constant envelope angle modulation equipment .52
8.10.3.3.3 Equipment measured as non-constant envelope modulation equipment .53
8.10.3.4 Characteristics of the adjacent channel transient power measuring device.54
9 Methods of measurement for receiver parameters .55
9.1 Maximum usable sensitivity (data or messages, conducted).55
9.1.1 Definition.55
9.1.2 Method of measurement with continuous bit streams.55
9.1.3 Method of measurement with messages .56
9.2 Average usable sensitivity (data or messages, field strength) .56
9.3 Level of the wanted signal for the degradation measurements (data or messages) .57
9.4 Error behaviour at high input levels .57
9.4.1 Definition.57
9.4.2 Method of measurement with continuous bit streams.57
9.4.3 Method of measurement with messages .58
9.5 Co-channel rejection.58
9.5.1 Definition.58
9.5.2 Method of measurement with continuous bit streams.58
9.5.3 Method of measurement with messages .59
9.6 Adjacent channel selectivity.61
9.6.1 Definition.61
9.6.2 Method of measurement with continuous bit streams.61
9.6.3 Method of measurement with messages .62
9.7 Spurious response rejection.63
9.7.1 Definition.63
9.7.2 Introduction to the method of measurement .64
9.7.3 Method of search over the "limited frequency range" .64
9.7.4 Method of measurement with continuous bit streams.65
9.7.5 Method of measurement with messages .66
9.8 Intermodulation response rejection .67
9.8.1 Definition.67
9.8.2 Method of measurement with continuous bit streams.67
9.8.3 Method of measurement with messages .68
9.9 Blocking or desensitization .69
9.9.1 Definition.69
9.9.2 Method of measurement with continuous bit streams.69
9.9.3 Method of measurement with messages .70
9.10
...