ISO/IEC 12862:2009

INTERNATIONAL ISO/IEC
STANDARD 12862
First edition
2009-06-15

Information technology — 120 mm
(8,54 Gbytes per side) and 80 mm
(2,66 Gbytes per side) DVD recordable
disk for dual layer (DVD-R for DL)
Technologies de l'information — Disques DVD enregistrables de
120 mm (8,54 Go par face) et 80 mm (2,66 Go par face) pour double
couche (DVD-R pour DL)




Reference number
ISO/IEC 12862:2009(E)
©
ISO/IEC 2009

---------------------- Page: 1 ----------------------
ISO/IEC 12862:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 12862:2009(E)
Contents Page
Foreword. vii
Introduction . viii
1 Scope. 1
2 Conformance. 1
2.1 Optical disk. 1
2.2 Generating system. 2
2.3 Receiving system. 2
3 Normative references. 2
4 Terms and definitions. 2
5 Conventions and notations . 6
5.1 Representation of numbers . 6
5.2 Names. 6
6 Abbreviated terms. 6
7 General description of a disk . 8
8 General requirement. 8
8.1 Environments . 8
8.1.1 Test environment. 8
8.1.2 Operating environment. 9
8.1.3 Storage environment. 9
8.1.4 Transportation. 10
8.2 Safety requirements. 10
8.3 Flammability. 10
9 Reference measurement devices. 10
9.1 Pick-Up Head (PUH). 10
9.1.1 PUH for measuring recorded disks. 10
9.1.2 PUH for measuring unrecorded disks . 12
9.2 Measurement conditions . 13
9.2.1 Recorded and unrecorded disk. 13
9.2.2 Recorded disk. 13
9.2.3 Unrecorded disk. 13
9.3 Normalized servo transfer function . 13
9.4 Reference servo for axial tracking . 14
9.4.1 Recorded disk. 14
9.4.2 Unrecorded disk. 15
9.5 Reference servo for radial tracking . 16
9.5.1 Recorded disk. 16
9.5.2 Unrecorded disk. 17
10 Dimensional characteristics. 18
10.1 Overall dimensions. 20
10.2 First transition area . 20
10.3 Second transition area . 21
10.4 Clamping Zone . 21
10.5 Third transition area . 21
10.6 R-Information Zone. 22
10.6.1 Sub-divisions of the R-Information Zone . 22
10.7 Information Zone. 22
10.7.1 Sub-divisions of the Information zone . 22
© ISO/IEC 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 12862:2009(E)
10.8 Track geometry. 23
10.8.1 Track Path. 24
10.9 Channel bit length. 24
10.10 Rim area. 24
10.11 Remark on tolerances. 25
10.12 Label. 25
11 Mechanical parameters. 25
11.1 Mass. 25
11.2 Moment of inertia . 25
11.3 Dynamic imbalance. 25
11.4 Sense of rotation. 25
11.5 Runout. 26
11.5.1 Axial runout . 26
11.5.2 Radial runout . 26
12 Optical parameters. 26
12.1 Recorded and unrecorded disk parameters. 26
12.1.1 Index of refraction. 26
12.1.2 Thickness of the transparent substrate. 26
12.1.3 Angular deviation. 27
12.1.4 Birefringence of the transparent substrate . 27
12.2 Recorded disk reflectivity. 27
12.3 Unrecorded disk parameters . 28
12.3.1 Polarity of reflectivity modulation . 28
12.3.2 Recording power sensitivity variation . 28
13 Operational signals for recorded disk . 28
13.1 Measurement conditions. 28
13.2 Read conditions . 28
13.3 Recorded disk high frequency (HF) signals. 28
13.3.1 Modulated amplitude . 28
13.3.2 Signal asymmetry. 29
13.3.3 Cross-track signal. 29
13.4 Quality of signals . 29
13.4.1 Jitter. 29
13.4.2 Random errors. 29
13.4.3 Defects. 30
13.5 Servo signals. 30
13.5.1 Differential phase tracking error signal . 30
13.5.2 Tangential push-pull signal. 30
13.6 Groove wobble signal. 32
14 Operational signals for the unrecorded disk . 33
14.1 Measurement conditions. 33
14.2 Recording conditions . 33
14.3 Write strategy for media testing . 33
14.3.1 Definition of the write pulse. 34
14.4 Servo signals. 35
14.4.1 Radial push-pull tracking error signal . 35
14.4.2 Defects. 36
14.5 Addressing signals . 36
14.5.1 Land Pre-Pit signal. 36
14.5.2 Groove wobble signal. 38
14.5.3 Relation in phase between wobble and Land Pre-Pit. 38
15 General. 39
16 Data Frames. 39
16.1 Identification Data (ID) . 40
16.2 ID Error Detection Code . 41
16.3 RSV. 41
16.4 Error Detection Code . 41
iv © ISO/IEC 2009 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 12862:2009(E)
17 Scrambled Frames. 42
18 ECC Block configuration . 43
19 Recording Frames. 44
20 Modulation. 45
21 Physical Sectors. 46
22 Suppress control of the d.c. component. 47
23 Linking scheme. 48
23.1 Structure of linking. 48
23.2 2K-Link and 32K-Link . 49
23.3 Lossless-Link. 49
24 General description of the Information Zone. 51
24.1 Layout of the Information Zone. 51
24.2 Physical Sector numbering. 52
25 Lead-in Zone, Middle Zone and Lead-out Zone . 53
25.1 Lead-in Zone. 53
25.1.1 Initial Zone . 54
25.1.2 Buffer Zone 0. 54
25.1.3 R-Physical Format Information Zone. 54
25.1.4 Reference Code Zone. 58
25.1.5 Buffer Zone 1. 58
25.1.6 Control Data Zone. 58
25.1.7 Extra Border Zone. 73
25.2 Middle Zone. 74
25.3 Lead-out Zone . 74
25.3.1 Structure of Lead-out Zone with Format4 RMD. 74
25.3.2 Superficial Extra Border Zone. 75
26 General description of the Unrecorded Zone . 75
26.1 Layout of the Unrecorded Zone . 76
26.2 ECC Block address. 77
26.3 ECC Block numbering. 77
27 Pre-pit Data format. 77
27.1 General description. 77
27.2 Pre-pit block structure. 80
27.3 Pre-pit data block configuration. 82
27.3.1 Relative address. 83
27.3.2 ECC Block address data configuration . 83
27.3.3 Parity A and Parity B . 83
27.3.4 Field ID0. 84
27.3.5 Field ID1. 85
27.3.6 Field ID2. 86
27.3.7 Field ID3 and Field ID4. 87
27.3.8 Field ID5. 89
28 Data structure of R-Information Zone and ODTA. 90
28.1 Layout of Disk Testing Area and Recording Management Area. 90
28.2 Structure of the Disk Testing Area. 91
28.3 Data configuration of the Recording Management Area (RMA) . 93
28.3.1 Sector format of the Recording Management Area. 93
28.3.2 Recording Management Data (Format1 RMD and Format4 RMD) . 95
Annex A (normative) Measurement of the angular deviation α. 127
Annex B (normative) Measurement of birefringence . 129
Annex C (normative) Measurement of the differential phase tracking error . 132
Annex D (normative) Measurement of light reflectance. 136
© ISO/IEC 2009 – All rights reserved v

---------------------- Page: 5 ----------------------
ISO/IEC 12862:2009(E)
Annex E (normative) Tapered cone for disk clamping . 138
Annex F (normative) Measurement of jitter . 139
Annex G (normative) 8-to-16 Modulation with RLL (2,10) requirements . 142
Annex H (normative) Optimum Power Control. 152
Annex I (normative) Measurement of the groove wobble amplitude . 154
Annex J (normative) Measurement methods for the operational signals for an unrecorded disk . 156
Annex K (normative) NBCA Code. 157
Annex L (normative) Border Zone . 163
Annex M (normative) Measurement method of the Land Pre-Pit signal. 176
Annex N (normative) Construction of Information Zone. 177
Annex O (normative) Recording order . 179
Annex P (normative) Clearance in the number of sectors . 180
Annex Q (normative) Anchor Point Re-mapping. 182
Annex R (informative) Measurement method of the Space layer thickness in a disk . 184
Annex S (informative) Transportation . 185


vi © ISO/IEC 2009 – All rights reserved

---------------------- Page: 6 ----------------------
ISO/IEC 12862:2009(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 12862 was prepared by Ecma International (as ECMA-382) and was adopted, under a special “fast-
track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its
approval by national bodies of ISO and IEC.
© ISO/IEC 2009 – All rights reserved vii

---------------------- Page: 7 ----------------------
ISO/IEC 12862:2009(E)
Introduction
Ecma Technical Committee TC31 was established in 1984 for the standardization of optical disks and
optical
...