ISO 9762:2000
(Main)Aerospace - Aircraft control wire rope assemblies - Dimensions and end-fitting combinations
Aerospace - Aircraft control wire rope assemblies - Dimensions and end-fitting combinations
This International Standard specifies the possible combinations and lengths of preformed flexible steel wire ropes for aircraft controls equipped with two end-fittings swaged on each end of the cable and the corresponding designations.
Aéronautique et espace — Câbles de commande d'aéronefs, équipés — Dimensions et combinaison des embouts
La présente Norme internationale définit les longueurs et les combinaisons possibles des câbles de commande d'aéronefs équipés de deux embouts sertis à chaque extrémité de câble, ainsi que la désignation correspondante.
General Information
- Status
- Published
- Publication Date
- 20-Dec-2000
- Technical Committee
- ISO/TC 20 - Aircraft and space vehicles
- Drafting Committee
- ISO/TC 20 - Aircraft and space vehicles
- Current Stage
- 9093 - International Standard confirmed
- Start Date
- 16-Jan-2025
- Completion Date
- 13-Dec-2025
Overview
ISO 9762:2000 - Aerospace - Aircraft control wire rope assemblies - Dimensions and end‑fitting combinations - defines the combinations, lengths and designation system for preformed flexible steel wire ropes used in aircraft control systems where two end‑fittings are swaged on each end. Prepared by ISO/TC 20/SC 12, the standard ensures consistent dimensions, identification and interchangeability of control cable assemblies used across aerospace applications.
Key topics
- Scope and purpose: Specifies permissible end‑fitting combinations and nominal lengths for preformed flexible steel wire ropes used in aircraft controls.
- End‑fitting requirements: End‑fittings must conform to the dimensional and material requirements in the referenced product standards (see Related Standards).
- Wire rope dimensions: Naked and finished wire rope constructions are referenced to ISO 2020‑1 for dimensional and load characteristics.
- Nominal length and tolerances: Defines the nominal length (Ls) and sets limit deviations (tolerances) by length ranges - tolerances increase with assembly length (see Table 2 in the standard).
- Material and surface treatment: Material and finishes for both end‑fittings and wire rope are required to comply with the applicable product standards referenced in the document.
- Coding and designation: Provides combination codes for end‑fittings (Table 1) and diameter/material codes (Table 3), plus the required designation format for each control wire rope assembly.
- Technical specification linkage: References ISO 9763 for technical specification details.
Applications and users
ISO 9762:2000 is intended for professionals involved in the design, manufacture, procurement and maintenance of aircraft control systems:
- Aerospace OEM engineers specifying control cables and end‑fittings
- Cable and end‑fitting manufacturers and suppliers ensuring compatibility and traceability
- MRO and maintenance organizations performing replacement or repair of control cable assemblies
- Procurement and quality assurance teams verifying conformity to aerospace dimensional standards
- Regulatory and certification bodies assessing component standardization
Using ISO 9762 helps ensure mechanical compatibility, safety, and interchangeability of swaged cable assemblies in flight controls, reducing design ambiguity and supporting reliable maintenance practices.
Related standards
Key normative references included in ISO 9762:
- ISO 2020‑1 - Preformed flexible steel wire rope for aircraft controls (dimensions and loads)
- ISO 9737, 9748, 9749, 9759, 9760 - Standards for swaged end‑fittings (eye‑ends, ball‑ends, stud‑ends, fork‑ends and fork‑ends for rolling bearings)
- ISO 9763 - Technical specifications for aircraft control wire rope assemblies
Keywords: ISO 9762:2000, aircraft control wire rope assemblies, end‑fitting combinations, preformed flexible steel wire ropes, aerospace cable standards.
ISO 9762:2000 - Aerospace — Aircraft control wire rope assemblies — Dimensions and end-fitting combinations Released:12/21/2000
ISO 9762:2000 - Aéronautique et espace — Câbles de commande d'aéronefs, équipés — Dimensions et combinaison des embouts Released:12/21/2000
Frequently Asked Questions
ISO 9762:2000 is a standard published by the International Organization for Standardization (ISO). Its full title is "Aerospace - Aircraft control wire rope assemblies - Dimensions and end-fitting combinations". This standard covers: This International Standard specifies the possible combinations and lengths of preformed flexible steel wire ropes for aircraft controls equipped with two end-fittings swaged on each end of the cable and the corresponding designations.
This International Standard specifies the possible combinations and lengths of preformed flexible steel wire ropes for aircraft controls equipped with two end-fittings swaged on each end of the cable and the corresponding designations.
ISO 9762:2000 is classified under the following ICS (International Classification for Standards) categories: 49.035 - Components for aerospace construction. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 9762:2000 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 9762
First edition
2000-12-15
Aerospace — Aircraft control wire rope
assemblies — Dimensions and end-fitting
combinations
Aéronautique et espace — Câbles de commande d'aéronefs, équipés —
Dimensions et combinaison des embouts
A
Reference number
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading
this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in
this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii
© ISO
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 9762 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles,
Subcommittee SC 12, Mechanical system parts.
iii
INTERNATIONAL STANDARD © ISO ISO 9762:2000(E)
Aerospace — Aircraft control wire rope assemblies — Dimensions
and end-fitting combinations
1 Scope
This International Standard specifies the possible combinations and lengths of preformed flexible steel wire ropes
for aircraft controls equipped with two end-fittings swaged on each end of the cable and the corresponding
designations.
2 Normative references
The following normative documents contain provisions which, through reference in this t
...
NORME ISO
INTERNATIONALE 9762
Première édition
2000-12-15
Aéronautique et espace — Câbles de
commande d'aéronefs, équipés —
Dimensions et combinaison des embouts
Aerospace — Aircraft control wire rope assemblies — Dimensions and end-
fitting combinations
A
Numéro de référence
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait
la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2000
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Imprimé en Suisse
ii
© ISO
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
La Norme internationale ISO 9762 a été élaborée par le comité technique ISO/TC 20, Aéronautique et espace,
sous-comité SC 12, Éléments de systèmes mécaniques.
iii
NORME INTERNATIONALE © ISO ISO 9762:2000(F)
Aéronautique et espace — Câbles de commande d'aéronefs,
équipés — Dimensions et combinaison des embouts
1 Domaine d’application
La présente Norme internationale définit les longueurs et les combinaisons possibles des câbles de commande
d'aéronefs équipés de deux embouts sertis à chaque extrémité de câble, ainsi que la désignation correspondante.
2 Références normatives
Les documents normatifs suivants contiennent des dispositions qui, par suite de
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...