ISO 23480:2013
(Main)Tools for pressing - Sliding plates
Tools for pressing - Sliding plates
ISO 23480:2013 specifies the main dimensions and tolerances of sliding plates, to be used in press tools (an application example is shown). It also specifies the designation of sliding plates.
Outillage de presse — Plaques de retenue
L'ISO 23480:2013 spécifie les dimensions principales et les tolérances des plaques de retenue, utilisées dans les outillages de presse. Elle spécifie également la désignation des plaques de retenue.
General Information
- Status
- Published
- Publication Date
- 28-Feb-2013
- Technical Committee
- ISO/TC 29/SC 8 - Tools for pressing and moulding
- Drafting Committee
- ISO/TC 29/SC 8 - Tools for pressing and moulding
- Current Stage
- 9093 - International Standard confirmed
- Start Date
- 20-Dec-2023
- Completion Date
- 13-Dec-2025
Relations
- Effective Date
- 06-Jun-2022
- Effective Date
- 03-Nov-2011
Overview
ISO 23480:2013 - Tools for pressing - Sliding plates defines standardized dimensions, tolerances and designation rules for sliding plates used in press tools. The second edition (2013) specifies two plate types (Type A: one-face; Type B: two-face), includes illustrative figures and dimension tables, and references general tolerancing, fastener and drawing-edge standards. The standard supports consistent design, procurement and interchangeability of sliding plates in metal forming and stamping tooling.
Key topics and requirements
- Scope: Main dimensions and tolerances of sliding plates for press tools and the required designation format.
- Types covered:
- Type A - one-face sliding plates (with figure and table of dimensions)
- Type B - two-face sliding plates (with separate figure and table)
- Dimensions and tolerances: Dimension tables and figures define nominal sizes; general tolerances are governed by ISO 2768‑1 (medium, m) where applicable. Surface roughness values are indicated in the figures.
- Fasteners and sockets: Hexagon socket screw specifications reference ISO 4762 for compatibility with standard fasteners.
- Drawing edges: All edges of undefined shape shall comply with ISO 13715.
- Material: Selection is left to the manufacturer’s discretion. The document gives example materials (e.g., steel for Type A, bronze with embedded solid lubricant for Type B) but does not mandate specific alloys.
- Designation rules: Sliding plates are designated by the term “Sliding plate”, the standard reference (ISO 23480), the type (A or B), and the plate dimensions b × h × l in millimetres.
Examples:- Sliding plate ISO 23480 – A 100 × 25 × 250
- Sliding plate ISO 23480 – B 60 × 30 × 125
Applications and users
ISO 23480 is intended for:
- Toolmakers and die designers specifying sliding plates in stamping, pressing and forming tools
- Production engineers and maintenance teams replacing or ordering standardized plates
- Purchasing departments and suppliers ensuring dimensional interchangeability
- Quality assurance professionals verifying compliance with tool component standards
Benefits include faster design cycles, simplified procurement, and improved interchangeability of press-tool components.
Related standards
- ISO 2768-1 - General tolerances (linear/angular)
- ISO 4762 - Hexagon socket head cap screws
- ISO 13715 - Technical drawings - Edges of undefined shape
Keywords: ISO 23480:2013, sliding plates, press tools, dimensions, tolerances, Type A, Type B, sliding plate designation, ISO 2768, ISO 4762, ISO 13715.
Frequently Asked Questions
ISO 23480:2013 is a standard published by the International Organization for Standardization (ISO). Its full title is "Tools for pressing - Sliding plates". This standard covers: ISO 23480:2013 specifies the main dimensions and tolerances of sliding plates, to be used in press tools (an application example is shown). It also specifies the designation of sliding plates.
ISO 23480:2013 specifies the main dimensions and tolerances of sliding plates, to be used in press tools (an application example is shown). It also specifies the designation of sliding plates.
ISO 23480:2013 is classified under the following ICS (International Classification for Standards) categories: 25.120.10 - Forging equipment. Presses. Shears. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 23480:2013 has the following relationships with other standards: It is inter standard links to ISO 10993-15:2019, ISO 23480:2008. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase ISO 23480:2013 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 23480
Second edition
2013-03-01
Tools for pressing — Sliding plates
Outillage de presse — Plaques de retenue
Reference number
©
ISO 2013
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Dimensions . 1
3.1 Type A, one-face sliding plates . 1
3.2 Type B, two-face sliding plates . 4
4 Material . 5
5 Designation . 5
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 23480 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for
pressing and moulding.
This second edition cancels and replaces the first edition (ISO 23480:2008), Figures 1, 2 and 3 of which
have been technically revised.
iv © ISO 2013 – All rights
...
NORME ISO
INTERNATIONALE 23480
Deuxième édition
2013-03-01
Outillage de presse — Plaques de
retenue
Tools for pressing — Sliding plates
Numéro de référence
©
ISO 2013
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Dimensions . 1
3.1 Type A, plaques de retenue à une face . 1
3.2 Type B, plaques de retenue à deux faces . 4
4 Matériau . 5
5 Désignation . 5
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne
la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives
ISO/CEI, Partie 2.
La tâche principale des comités techniques est d’élaborer les Normes internationales. Les projets de
Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour vote.
Leur publication comme Normes internationales requiert l’approbation de 75 % au moins des comités
membres votants.
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
L’ISO 23480 a été élaborée par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 8, Outillage
de presse et de moulage.
Cette deuxième édition annule et remplace la première édition (ISO 23480:2008), dont les Figures 1, 2
et 3 ont fait l’objet d’une révision technique.
iv © ISO 2013 – Tous droits réservés
NORME INTERNATIONALE ISO 23480:2013(F)
Outillage de pres
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...