ISO 15512:2016
(Main)Plastics — Determination of water content
Plastics — Determination of water content
1.1 ISO 15512:2016 specifies methods for the determination of the water content of plastics in the form of powder, granules, and finished articles. These methods do not test for water absorption (kinetics and equilibrium) of plastics as measured by ISO 62. Method A is suitable for the determination of water content as low as 0,1 % with an accuracy of 0,1 %. Method B and Method C are suitable for the determination of water content as low as 0,01 % with an accuracy of 0,01 %. Water content is an important parameter for processing materials and has to remain below the level specified in the appropriate material standard. 1.2 Four alternative methods are specified in this International Standard. ? Method A is an extraction method using anhydrous methanol followed by a Karl Fischer titration of the extracted water. It can be used for all plastics and is applicable to granules smaller than 4 mm × 4 mm × 3 mm. The method can also be used for, e.g. prepolymer materials in the form of a powder that are insoluble in methanol. ? Method B1 is a vaporization method using a tube oven. The water contained in the test portion is vaporized and carried to the titration cell by a dry air or nitrogen carrier gas, followed by a Karl Fischer titration of the collected water. It can be used for all plastics and is applicable to granules smaller than 4 mm × 4 mm × 3 mm. ? Method B2 is a vaporization method using a heated sample vial. The water contained in the test portion is vaporized and carried to the titration cell by a dry air or nitrogen carrier gas, followed by a Karl Fischer titration of the collected water. It can be used for all plastics and is applicable to granules smaller than 4 mm × 4 mm × 3 mm. ? Method C is a manometric method. The water content is determined from the increase in pressure, which results when the water is evaporated under a vacuum. This method is not applicable to plastic samples containing volatile compounds, other than water, in amounts contributing significantly to the vapour pressure at room temperature. Checks for the presence of large amounts of volatile compounds are to be carried out periodically, for example by gas chromatography. Such checks are particularly required for new types or grades of material.
Plastiques — Dosage de l'eau
1.1 ISO 15512:2016 spécifie des méthodes pour le dosage de l'eau dans les plastiques sous forme de poudre, de granulés et d'articles finis. Ces méthodes ne contrôlent pas l'absorption d'eau (cinétique et équilibre) des plastiques, cet aspect étant traité dans l'ISO 62. La Méthode A est applicable au dosage de l'eau à des niveaux aussi faibles que 0,1 % avec une précision de 0,1 %. La Méthode B et la Méthode C sont applicables au dosage de l'eau à des niveaux aussi faibles que 0,01 % avec une précision de 0,01 %. La teneur en eau est un paramètre important de la mise en ?uvre des matériaux et il convient qu'elle reste en dessous du niveau spécifié dans la norme de produit appropriée. 1.2 Quatre méthodes possibles sont spécifiées dans la présente Norme internationale. ? La méthode A consiste en une extraction de l'eau à l'aide de méthanol anhydre suivie d'un titrage de l'eau extraite par la méthode de Karl Fischer. Elle peut être utilisée pour tous les plastiques et est applicable aux granulés de moins de 4 mm × 4 mm × 3 mm. Elle peut également être utilisée, par exemple, pour les poudres de prépolymère insolubles dans le méthanol. ? La méthode B1 procède par vaporisation dans un four tubulaire. L'eau contenue dans la prise d'essai est transformée en vapeur, qui est transférée à l'aide d'un gaz vecteur d'air sec ou d'azote dans la cuve de titrage, l'eau recueillie est ensuite titrée par la méthode de Karl Fischer. Cette méthode peut être utilisée pour tous les plastiques et est applicable aux granulés de moins de 4 mm × 4 mm × 3 mm. ? La méthode B2 procède par vaporisation dans un flacon d'échantillon chauffé. L'eau contenue dans la prise d'essai est transformée en vapeur, qui est transférée à l'aide d'un gaz vecteur d'air sec ou d'azote dans la cuve de titrage, l'eau recueillie est ensuite titrée par la méthode de Karl Fischer. Cette méthode peut être utilisée pour tous les plastiques et est applicable aux granulés de moins de 4 mm × 4 mm × 3 mm. ? La méthode C est une méthode manométrique. Le dosage de l'eau se fonde sur l'augmentation de pression après évaporation de l'eau sous vide. Cette méthode n'est pas applicable aux échantillons de plastiques contenant des composés volatils, autres que l'eau, en quantité suffisante pour avoir un effet significatif sur la pression de vapeur à température ambiante. Il convient d'effectuer périodiquement des vérifications de la présence de grandes quantités de composés volatils, par exemple par chromatographie en phase gazeuse. Ces vérifications sont particulièrement nécessaires pour les nouveaux types ou les nouvelles qualités de matériaux.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 15512
Fourth edition
2016-10-15
Plastics — Determination of water
content
Plastiques — Dosage de l’eau
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Method A — Extraction with anhydrous methanol . 1
3.1 Principle . 1
3.2 Reagents. 2
3.3 Apparatus . 2
3.4 Preparation of test sample . 2
3.4.1 Granules or powder . 2
3.4.2 Finished articles . 2
3.5 Procedure . 3
3.5.1 Precautions . 3
3.5.2 Preparation of test portions . 3
3.5.3 Determination . 3
3.6 Expression of results . 3
3.7 Precision . 4
4 Method B1 — Water vaporization using a heating tube oven . 4
4.1 Principle . 4
4.2 Reagents. 4
4.3 Apparatus . 5
4.4 Preparation of test sample . 7
4.5 Procedure . 7
4.5.1 Precautions . 7
4.5.2 Preparation of apparatus . 7
4.5.3 Equipment check . 7
4.5.4 Determination . 8
4.6 Expression of results . 8
4.7 Precision . 9
5 Method B2 — Water vaporization using a heated sample vial . 9
5.1 Principle . 9
5.2 Reagents. 9
5.3 Apparatus .10
5.4 Preparation of test sample .11
5.5 Procedure .12
5.5.1 Preparation of apparatus .12
5.5.2 Equipment check .12
5.5.3 Determination .12
5.6 Expression of results .14
5.7 Precision .14
6 Method C — Manometric method .15
6.1 Principle .15
6.2 Reagents.15
6.3 Apparatus .15
6.4 Preparation of test sample .16
6.5 Procedure .16
6.5.1 Equipment .16
6.5.2 Outgassing .17
6.5.3 Calibration .17
6.5.4 Determination .19
6.6 Expression of results .20
6.7 Precision .20
7 Test report .20
Annex A (informative) Alternative sample preparation methods and titration methods .21
Annex B (informative) Selection of the optimum heating temperature for the water
content determination .22
Annex C (normative) Determination of the water content of a water standard .24
Bibliography .25
iv © ISO 2016 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the World Trade Organization (WTO)
principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword – Supplementary
information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 5, Physical-
chemical properties.
This fourth edition cancels and replaces the third edition (ISO 15512:2014), of which it constitutes a
minor revision to update information in 6.2.1.
Introduction
The interlaboratory comparability of the water content determination of plastics is often low. Major
causes for this are the sample packaging, sample handling, and differences between equipment and
settings. Samples have to, e.g.
...
INTERNATIONAL ISO
STANDARD 15512
Fourth edition
2016-10-15
Plastics — Determination of water
content
Plastiques — Dosage de l’eau
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Method A — Extraction with anhydrous methanol . 1
3.1 Principle . 1
3.2 Reagents. 2
3.3 Apparatus . 2
3.4 Preparation of test sample . 2
3.4.1 Granules or powder . 2
3.4.2 Finished articles . 2
3.5 Procedure . 3
3.5.1 Precautions . 3
3.5.2 Preparation of test portions . 3
3.5.3 Determination . 3
3.6 Expression of results . 3
3.7 Precision . 4
4 Method B1 — Water vaporization using a heating tube oven . 4
4.1 Principle . 4
4.2 Reagents. 4
4.3 Apparatus . 5
4.4 Preparation of test sample . 7
4.5 Procedure . 7
4.5.1 Precautions . 7
4.5.2 Preparation of apparatus . 7
4.5.3 Equipment check . 7
4.5.4 Determination . 8
4.6 Expression of results . 8
4.7 Precision . 9
5 Method B2 — Water vaporization using a heated sample vial . 9
5.1 Principle . 9
5.2 Reagents. 9
5.3 Apparatus .10
5.4 Preparation of test sample .11
5.5 Procedure .12
5.5.1 Preparation of apparatus .12
5.5.2 Equipment check .12
5.5.3 Determination .12
5.6 Expression of results .14
5.7 Precision .14
6 Method C — Manometric method .15
6.1 Principle .15
6.2 Reagents.15
6.3 Apparatus .15
6.4 Preparation of test sample .16
6.5 Procedure .16
6.5.1 Equipment .16
6.5.2 Outgassing .17
6.5.3 Calibration .17
6.5.4 Determination .19
6.6 Expression of results .20
6.7 Precision .20
7 Test report .20
Annex A (informative) Alternative sample preparation methods and titration methods .21
Annex B (informative) Selection of the optimum heating temperature for the water
content determination .22
Annex C (normative) Determination of the water content of a water standard .24
Bibliography .25
iv © ISO 2016 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the World Trade Organization (WTO)
principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword – Supplementary
information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 5, Physical-
chemical properties.
This fourth edition cancels and replaces the third edition (ISO 15512:2014), of which it constitutes a
minor revision to update information in 6.2.1.
Introduction
The interlaboratory comparability of the water content determination of plastics is often low. Major
causes for this are the sample packaging, sample handling, and differences between equipment and
settings. Samples have to, e.g.
...
NORME ISO
INTERNATIONALE 15512
Quatrième édition
2016-10-15
Plastiques — Dosage de l’eau
Plastics — Determination of water content
Numéro de référence
©
ISO 2016
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – Tous droits réservés
Sommaire Page
Avant-propos .v
Introduction .vi
1 Domaine d’application . 1
2 Références normatives . 1
3 Méthode A — Extraction de l’eau au méthanol anhydre . 2
3.1 Principe . 2
3.2 Réactifs . 2
3.3 Appareillage. 2
3.4 Préparation de l’échantillon . 2
3.4.1 Granulés ou poudre . 2
3.4.2 Articles finis . 3
3.5 Mode opératoire . 3
3.5.1 Précautions . 3
3.5.2 Préparation des prises d’essai . 3
3.5.3 Dosage . 3
3.6 Expression des résultats . 3
3.7 Fidélité . 4
4 Méthode B1 — Vaporisation de l’eau dans un four tubulaire . 4
4.1 Principe . 4
4.2 Réactifs . 4
4.3 Appareillage. 5
4.4 Préparation de l’échantillon . 7
4.5 Mode opératoire . 7
4.5.1 Précautions . 7
4.5.2 Préparation de l’appareillage . 7
4.5.3 Vérification de l’équipement . 7
4.5.4 Dosage . 8
4.6 Expression des résultats . 8
4.7 Fidélité . 9
5 Méthode B2 — Vaporisation de l’eau en utilisant une fiole à échantillon chauffée .9
5.1 Principe . 9
5.2 Réactifs . 9
5.3 Appareillage.10
5.4 Préparation de l’échantillon .11
5.5 Mode opératoire .12
5.5.1 Préparation de l’appareillage .12
5.5.2 Vérification de l’équipement .12
5.5.3 Dosage .12
5.6 Expression des résultats .14
5.7 Fidélité .15
6 Méthode C — Méthode manométrique .15
6.1 Principe .15
6.2 Réactifs .15
6.3 Appareillage.15
6.4 Préparation de l’échantillon .16
6.5 Mode opératoire .16
6.5.1 Équipement .16
6.5.2 Purge .18
6.5.3 Étalonnage .18
6.5.4 Dosage .19
6.6 Expression des résultats .20
6.7 Fidélité .20
7 Rapport d’essai .21
Annexe A (informative) Autres méthodes de préparation des échantillons et de titrage .22
Annexe B (informative) Sélection de la température de chauffage optimale pour le dosage
de l’eau .24
Annexe C (normative) Dosage de l’eau contenue dans un étalon d’eau .26
Bibliographie .27
iv © ISO 2016 – Tous droits réservés
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation
de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’Organisation
mondiale du commerce (OMC) concernant les obstacles techniques au commerce (OTC) voir le lien
suivant: www.iso.org/iso/fr/foreword.html.
Le comité chargé de l’élaboration du présent document est l’ISO/TC 61, Plastiques, sous-comité SC 5,
Propriétés physiques.
Cette quatrième édition annule et remplace la troisième édition (ISO 15512:2014), dont elle constitue
une révision mineure avec mise à jour du paragraph
...
NORME ISO
INTERNATIONALE 15512
Quatrième édition
2016-10-15
Plastiques — Dosage de l’eau
Plastics — Determination of water content
Numéro de référence
©
ISO 2016
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2016, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – Tous droits réservés
Sommaire Page
Avant-propos .v
Introduction .vi
1 Domaine d’application . 1
2 Références normatives . 1
3 Méthode A — Extraction de l’eau au méthanol anhydre . 2
3.1 Principe . 2
3.2 Réactifs . 2
3.3 Appareillage. 2
3.4 Préparation de l’échantillon . 2
3.4.1 Granulés ou poudre . 2
3.4.2 Articles finis . 3
3.5 Mode opératoire . 3
3.5.1 Précautions . 3
3.5.2 Préparation des prises d’essai . 3
3.5.3 Dosage . 3
3.6 Expression des résultats . 3
3.7 Fidélité . 4
4 Méthode B1 — Vaporisation de l’eau dans un four tubulaire . 4
4.1 Principe . 4
4.2 Réactifs . 4
4.3 Appareillage. 5
4.4 Préparation de l’échantillon . 7
4.5 Mode opératoire . 7
4.5.1 Précautions . 7
4.5.2 Préparation de l’appareillage . 7
4.5.3 Vérification de l’équipement . 7
4.5.4 Dosage . 8
4.6 Expression des résultats . 8
4.7 Fidélité . 9
5 Méthode B2 — Vaporisation de l’eau en utilisant une fiole à échantillon chauffée .9
5.1 Principe . 9
5.2 Réactifs . 9
5.3 Appareillage.10
5.4 Préparation de l’échantillon .11
5.5 Mode opératoire .12
5.5.1 Préparation de l’appareillage .12
5.5.2 Vérification de l’équipement .12
5.5.3 Dosage .12
5.6 Expression des résultats .14
5.7 Fidélité .15
6 Méthode C — Méthode manométrique .15
6.1 Principe .15
6.2 Réactifs .15
6.3 Appareillage.15
6.4 Préparation de l’échantillon .16
6.5 Mode opératoire .16
6.5.1 Équipement .16
6.5.2 Purge .18
6.5.3 Étalonnage .18
6.5.4 Dosage .19
6.6 Expression des résultats .20
6.7 Fidélité .20
7 Rapport d’essai .21
Annexe A (informative) Autres méthodes de préparation des échantillons et de titrage .22
Annexe B (informative) Sélection de la température de chauffage optimale pour le dosage
de l’eau .24
Annexe C (normative) Dosage de l’eau contenue dans un étalon d’eau .26
Bibliographie .27
iv © ISO 2016 – Tous droits réservés
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation
de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’Organisation
mondiale du commerce (OMC) concernant les obstacles techniques au commerce (OTC) voir le lien
suivant: www.iso.org/iso/fr/foreword.html.
Le comité chargé de l’élaboration du présent document est l’ISO/TC 61, Plastiques, sous-comité SC 5,
Propriétés physiques.
Cette quatrième édition annule et remplace la troisième édition (ISO 15512:2014), dont elle constitue
une révision mineure avec mise à jour du paragraph
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.