Round steel short link chains for lifting purposes — Medium tolerance sling chains — Grade 4, stainless steel

This document specifies the requirements for medium tolerance sling chains of grade 4 from stainless steel for use preferably in chain slings of grade 4 from stainless steel or for other lifting purposes. The range of nominal diameter, dn, covered by this document is from 4 mm to 22 mm. These sling chains are round steel short link chains with a nominal pitch, pn = 3 × dn, electrically welded, solution-annealed and tested. They are for use in the temperature range ?100 °C to +400 °C. They comply with the general conditions of acceptance of ISO 1834. NOTE 1 Because sling chains are solution-annealed in the finished condition, they can be used without restrictions with regard to the corrosion resistance of the steels according to 5.2. Higher grades of stainless steel chains are achieved by cold drawing of the wire prior to the chain manufacturing. Therefore, solution annealing is not possible without reduction of strength. The weld seam, in particular, represents a critical area with regard to the corrosion resistance. NOTE 2 Resistance butt welding and flash welding are listed in ISO 4063.

Chaînes de levage en acier de section ronde à maillons courts — Chaînes d'élingue de tolérance moyenne — Classe de qualité 4, acier inoxydable

General Information

Status
Published
Publication Date
29-Aug-2018
Current Stage
9093 - International Standard confirmed
Completion Date
04-Oct-2023
Ref Project

Relations

Buy Standard

Standard
ISO 1835:2018 - Round steel short link chains for lifting purposes -- Medium tolerance sling chains -- Grade 4, stainless steel
English language
17 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 1835
Second edition
2018-08
Round steel short link chains for
lifting purposes — Medium tolerance
sling chains — Grade 4, stainless steel
Chaînes de levage en acier de section ronde à maillons courts —
Chaînes de élingue de tolérance moyenne — Classe de qualité 4, acier
inoxydable
Reference number
ISO 1835:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 1835:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 1835:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions, masses and designation . 2
4.1 Dimensions and masses . 2
4.2 Designation . 4
5 Requirements . 5
5.1 General . 5
5.2 Material . 5
5.3 Heat treatment . 5
5.4 Surface condition . 5
5.5 Dimensions . 5
5.5.1 Diameter . 5
5.5.2 Pitch . 5
5.5.3 Width . 5
5.5.4 Weld dimensions . 5
5.5.5 Length dimensionally affected by welding . 6
5.6 Working load limit (WLL) .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.