IEC 60794-2-50:2008
(Main)Optical fibre cables - Part 2-50: Indoor cables - Family specification for simplex and duplex cables for use in terminated cable assemblies
Optical fibre cables - Part 2-50: Indoor cables - Family specification for simplex and duplex cables for use in terminated cable assemblies
IEC 60794-2-50:2008 provides requirements for simplex and duplex optical fibre cables for use in terminated cable assemblies or for termination with optical fibre passive components. This standard cancels and replaces IEC/PAS 60794-2-50 published in 2004. This standard is to be used in conjunction with IEC 60794-1-1, IEC 60794-1-2 and IEC 60794-2.
Câbles à fibres optiques - Partie 2-50: Câbles intérieurs - Spécification de famille pour les câbles simplex et duplex utilisés dans les ensembles de câbles équipés
La CEI 60794-2-50:2008 donne les exigences pour les câbles simplex et duplex à fibres optiques utilisés dans des ensembles de câbles équipés ou en vue de la finition par des composants passifs à fibres optiques. La présente norme annule et remplace la CEI/PAS 60794-2-50 parue en 2004. La présente norme doit être lue conjointement avec la CEI 60794-1-1, la CEI 60794-1-2 et la CEI 60794-2.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 60794-2-50
Edition 1.0 2008-04
INTERNATIONAL
STANDARD
Optical fibre cables –
Part 2-50: Indoor cables – Family specification for simplex and duplex cables
for use in terminated cable assemblies
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60794-2-50
Edition 1.0 2008-04
INTERNATIONAL
STANDARD
Optical fibre cables –
Part 2-50: Indoor cables – Family specification for simplex and duplex cables
for use in terminated cable assemblies
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
V
ICS 33.180-10 ISBN 2-8318-9738-6
– 2 – 60794-2-50 © IEC:2008(E)
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 Terms and definitions .7
4 Construction .7
4.1 General .7
4.2 Optical fibres and primary coating .7
4.3 Buffer .7
4.4 Tube.8
4.5 Strength and anti-buckling members .8
4.6 Sheath .8
4.7 Sheath marking .8
4.8 Examples of cable constructions .8
5 Tests .8
5.1 Dimensions .9
5.2 Mechanical requirements.9
5.2.1 Tensile performance.9
5.2.2 Crush .9
5.2.3 Impact .10
5.2.4 Repeated bending .10
5.2.5 Bend.10
5.2.6 Torsion .11
5.2.7 Bend at low temperature.11
5.2.8 Kink.11
5.2.9 Sheath pull-off force .11
5.2.10 Buffered fibre movement in compression .12
5.3 Environmental requirements .12
5.3.1 Temperature cycling .12
5.3.2 Sheath shrinkage.12
5.4 Transmission requirements .13
5.5 Fire performance.13
Annex A (informative) Examples of some types of cable construction .14
Annex B (normative) METHOD E21 – Sheath pull-off force for optical fibre cable for
use in patch cords .17
Annex C (normative) METHOD F11 – Sheath shrinkage for optical fibre cable for use
in patchcords .22
Annex D (normative) METHOD E22 – Buffered fibre movement under compression in
optical fibre cables for use in patchcords .24
Annex E (normative) METHOD F12 – Temperature cycling for optical fibre cable for
use in patchcords .26
Annex F (normative) – Guidance on the selection of tests applicable to optical fibre
cables for use in patchcords .28
Bibliography.31
Figure A.1 – Simplex loose non-buffered fibre cable .
Figure A.2 – Simplex ruggedized fibre cable .14
60794-2-50 © IEC:2008(E) – 3 –
Figure A.3 – Duplex loose non-buffered fibre cable.14
Figure A.4 – Duplex ruggedized fibre cable.15
Figure A.5 – Duplex ruggedized fibre zip cord.15
Figure A.6 – Duplex ruggedized flat cable.15
Figure A.7 – Duplex ruggedized round cable.16
Figure B.1 – Schematic of test arrangement .19
Figure B.2 – Example of pulling jig.20
Figure B.3 – Cable sample preparation .21
Figure D.1 – Test set up for fibre movement under compression.25
Table 1 – Dimensions of buffered fibres.8
Table 2 – Temperature cycling severities .12
Table F.1 – Cable test method summary.28
Table F.2 – Cable testing agreement .30
– 4 – 60794-2-50 © IEC:2008(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL FIBRE CABLES –
Part 2-50: Indoor cables –
Family specification for simplex and duplex cables
for use in terminated cable assemblies
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60794-2-50 has been prepared by subcommittee 86A: Fibres and
cables, of IEC technical committee 86: Fibre optics.
This standard cancels and replaces IEC/PAS 60794-2-50 published in 2004. This first edition
constitutes a technical revision.
This standard is to be used in conjunction with IEC 60794-1-1, IEC 60794-1-2 and
IEC 60794-2.
60794-2-50 © IEC:2008(E) – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
86A/1204/FDIS 86A/1223/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 60794 series, under the general title Optical fibre cables, can be
found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication will be issued at a later date.
----------
...
IEC 60794-2-50
Edition 1.0 2008-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical fibre cables –
Part 2-50: Indoor cables – Family specification for simplex and duplex cables for
use in terminated cable assemblies
Câbles à fibres optiques –
Partie 2-50: Câbles intérieurs – Spécification de famille pour les câbles simplex
et duplex utilisés dans les ensembles de câbles équipés
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60794-2-50
Edition 1.0 2008-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical fibre cables –
Part 2-50: Indoor cables – Family specification for simplex and duplex cables for
use in terminated cable assemblies
Câbles à fibres optiques –
Partie 2-50: Câbles intérieurs – Spécification de famille pour les câbles simplex
et duplex utilisés dans les ensembles de câbles équipés
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
V
CODE PRIX
ICS 33.180.10 ISBN 2-8318-9902-8
– 2 – 60794-2-50 © IEC:2008
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 Terms and definitions .7
4 Construction .7
4.1 General .7
4.2 Optical fibres and primary coating .7
4.3 Buffer .7
4.4 Tube.8
4.5 Strength and anti-buckling members .8
4.6 Sheath .8
4.7 Sheath marking .8
4.8 Examples of cable constructions .8
5 Tests .8
5.1 Dimensions .9
5.2 Mechanical requirements.9
5.2.1 Tensile performance.9
5.2.2 Crush .9
5.2.3 Impact .10
5.2.4 Repeated bending .10
5.2.5 Bend.10
5.2.6 Torsion .11
5.2.7 Bend at low temperature.11
5.2.8 Kink.11
5.2.9 Sheath pull-off force .11
5.2.10 Buffered fibre movement in compression .12
5.3 Environmental requirements .12
5.3.1 Temperature cycling .12
5.3.2 Sheath shrinkage.13
5.4 Transmission requirements .13
5.5 Fire performance.13
Annex A (informative) Examples of some types of cable construction .14
Annex B (normative) METHOD E21 – Sheath pull-off force for optical fibre cable for
use in patch cords .17
Annex C (normative) METHOD F11 – Sheath shrinkage for optical fibre cable for use
in patchcords .22
Annex D (normative) METHOD E22 – Buffered fibre movement under compression in
optical fibre cables for use in patchcords .24
Annex E (normative) METHOD F12 – Temperature cycling for optical fibre cable for
use in patchcords .26
Annex F (normative) Guidance on the selection of tests applicable to optical fibre
cables for use in patchcords .28
Bibliography.
Figure A.1 – Simplex loose non-buffered fibre cable .14
60794-2-50 © IEC:2008 – 3 –
Figure A.2 – Simplex ruggedized fibre cable .14
Figure A.3 – Duplex loose non-buffered fibre cable.14
Figure A.4 – Duplex ruggedized fibre cable.15
Figure A.5 – Duplex ruggedized fibre zip cord.15
Figure A.6 – Duplex ruggedized flat cable.15
Figure A.7 – Duplex ruggedized round cable.16
Figure B.1 – Schematic of test arrangement .19
Figure B.2 – Example of pulling jig.20
Figure B.3 – Cable sample preparation .21
Figure D.1 – Test set up for fibre movement under compression.25
Table 1 – Dimensions of buffered fibres.8
Table 2 – Temperature cycling severities .12
Table F.1 – Cable test method summary.28
Table F.2 – Cable testing agreement .30
– 4 – 60794-2-50 © IEC:2008
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL FIBRE CABLES –
Part 2-50: Indoor cables –
Family specification for simplex and duplex cables
for use in terminated cable assemblies
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.