ETSI EN 300 296-2 V1.2.1 (2009-02)

ETSI EN 300 296-2 V1.2.1 (2009-02)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering essential requirements
under article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 ETSI EN 300 296-2 V1.2.1 (2009-02)



Reference
REN/ERM-TGDMR-272-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 296-2 V1.2.1 (2009-02)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .5
1 Scope.6
2 References.6
2.1 Normative references.6
2.2 Informative references.6
3 Definitions, symbols and abbreviations .7
3.1 Definitions.7
3.2 Symbols.7
3.3 Abbreviations.7
4 Technical specifications .7
4.1 Environmental profile.7
4.2 Transmitter requirements.7
4.2.1 Frequency error.7
4.2.1.1 Definition.7
4.2.1.2 Limit.7
4.2.1.3 Methods of measurement.7
4.2.2 Effective radiated power.8
4.2.2.1 Definition.8
4.2.2.2 Limit.8
4.2.2.3 Methods of measurement.8
4.2.3 Maximum permissible frequency deviation.8
4.2.3.1 Definition.8
4.2.3.2 Limit.8
4.2.3.3 Methods of measurement.8
4.2.4 Adjacent and alternate channel power .8
4.2.4.1 Definition.8
4.2.4.2 Limit.8
4.2.4.3 Methods of measurement.8
4.2.5 Radiated unwanted emissions in the spurious domain.8
4.2.5.1 Definition.8
4.2.5.2 Limit.8
4.2.5.3 Methods of measurement.8
4.3 Receiver requirements.9
4.3.1 Average usable sensitivity (field strength, speech).9
4.3.1.1 Definition.9
4.3.1.2 Limit.9
4.3.1.3 Method of measurement.9
4.3.2 Co-channel rejection.9
4.3.2.1 Definition.9
4.3.2.2 Limit.9
4.3.2.3 Method of measurement.9
4.3.3 Adjacent channel selectivity .9
4.3.3.1 Definition.9
4.3.3.2 Limit.9
4.3.3.3 Method of measurement.9
4.3.4 Spurious response rejection .9
4.3.4.1 Definition.9
4.3.4.2 Limit.9
4.3.4.3 Method of measurement.10
4.3.5 Intermodulation response rejection.10
4.3.5.1 Definition.10
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 296-2 V1.2.1 (2009-02)
4.3.5.2 Limit.10
4.3.5.3 Method of measurement.10
4.3.6 Blocking or desensitization.10
4.3.6.1 Definition.10
4.3.6.2 Limit.10
4.3.6.3 Method of measurement.10
4.3.7 Spurious radiations.10
4.3.7.1 Definition.10
4.3.7.2 Limit.10
4.3.7.3 Method of measurement.10
5 Testing for compliance with technical requirements.11
5.1 Environmental conditions for testing .11
5.1.1 Normal and extreme test-conditions .11
5.1.2 Test power source .11
5.1.3 Choice of samples for test suites.11
5.2 Interpretation of the measurement results .11
5.3 Essential radio test suites.11
5.3.1 Frequency error.11
5.3.2 Effective radiated power.11
5.3.3 Maximum frequency deviation.12
5.3.4 Adjacent and alternate channel power .12
5.3.5 Radiated unwanted emission in the spurious domain .12
5.3.6 Spurious radiations.12
5.4 Other test specifications.12
5.4.1 Average usable sensitivity (speech, field strength).12
5.4.2 Co-channel rejection.12
5.4.3 Adjacent channel selectivity .12
5.4.4 Spurious response rejection .12
5.4.5 Intermodulation response rejection.12
5.4.6 Blocking or desensitization.12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT).13
Annex C (informative): Bibliography.16
History .17

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 296-2 V1.2.1 (2009-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC of the European Parliament and of
the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [i.1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 9 February 2009
Date of latest announcement of this EN (doa): 31 May 2009
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2009
Date of withdrawal of any conflicting National Standard (dow): 30 November 2010

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 300 296-2 V1.2.1 (2009-02)
1 Scope
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference
and to make acceptable use of the available frequencies.
The present document applies to equipment with integral
...

Final draft ETSI EN 300 296-2 V1.2.1 (2008-12)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering essential requirements
under article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 296-2 V1.2.1 (2008-12)



Reference
REN/ERM-TGDMR-272-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2008.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 296-2 V1.2.1 (2008-12)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 9
4.3.4.1 Definition . 9
4.3.4.2 Limit . 9
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 296-2 V1.2.1 (2008-12)
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.4 Other test specifications . 12
5.4.1 Average usable sensitivity (speech, field strength) . 12
5.4.2 Co-channel rejection . 12
5.4.3 Adjacent channel selectivity . 12
5.4.4 Spurious response rejection . 12
5.4.5 Intermodulation response rejection . 12
5.4.6 Blocking or desensitization . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex C (informative): Bibliography . 16
History . 17

ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 296-2 V1.2.1 (2008-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC of the European Parliament and of
the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [i.1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 296-2 V1.2.1 (2008-12)
1 Scope
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference
and to make acceptable use of the available frequencies.
The present document applies to equipment with integral a
...

Draft ETSI EN 300 296-2 V1.2.1 (2008-07)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering essential requirements
under article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 296-2 V1.2.1 (2008-07)



Reference
REN/ERM-TGDMR-272-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2008.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 296-2 V1.2.1 (2008-07)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .5
1 Scope.6
2 References.6
2.1 Normative references.6
2.2 Informative references.7
3 Definitions, symbols and abbreviations .7
3.1 Definitions.7
3.2 Symbols.7
3.3 Abbreviations.7
4 Technical specifications .7
4.1 Environmental profile.7
4.2 Transmitter requirements.7
4.2.1 Frequency error.7
4.2.1.1 Definition.7
4.2.1.2 Limit.8
4.2.1.3 Methods of measurement.8
4.2.2 Effective radiated power.8
4.2.2.1 Definition.8
4.2.2.2 Limit.8
4.2.2.3 Methods of measurement.8
4.2.3 Maximum permissible frequency deviation.8
4.2.3.1 Definition.8
4.2.3.2 Limit.8
4.2.3.3 Methods of measurement.8
4.2.4 Adjacent and alternate channel power .8
4.2.4.1 Definition.8
4.2.4.2 Limit.8
4.2.4.3 Methods of measurement.8
4.2.5 Radiated unwanted emissions in the spurious domain.8
4.2.5.1 Definition.8
4.2.5.2 Limit.9
4.2.5.3 Methods of measurement.9
4.3 Receiver requirements.9
4.3.1 Average usable sensitivity (field strength, speech).9
4.3.1.1 Definition.9
4.3.1.2 Limit.9
4.3.1.3 Method of measurement.9
4.3.2 Co-channel rejection.9
4.3.2.1 Definition.9
4.3.2.2 Limit.9
4.3.2.3 Method of measurement.9
4.3.3 Adjacent channel selectivity .9
4.3.3.1 Definition.9
4.3.3.2 Limit.9
4.3.3.3 Method of measurement.9
4.3.4 Spurious response rejection .10
4.3.4.1 Definition.10
4.3.4.2 Limit.10
4.3.4.3 Method of measurement.10
4.3.5 Intermodulation response rejection.10
4.3.5.1 Definition.10
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 296-2 V1.2.1 (2008-07)
4.3.5.2 Limit.10
4.3.5.3 Method of measurement.10
4.3.6 Blocking or desensitization.10
4.3.6.1 Definition.10
4.3.6.2 Limit.10
4.3.6.3 Method of measurement.10
4.3.7 Spurious radiations.10
4.3.7.1 Definition.10
4.3.7.2 Limit.10
4.3.7.3 Method of measurement.10
5 Testing for compliance with technical requirements.11
5.1 Environmental conditions for testing .11
5.1.1 Normal and extreme test-conditions .11
5.1.2 Test power source .11
5.1.3 Choice of samples for test suites.11
5.2 Interpretation of the measurement results .11
5.3 Essential radio test suites.11
5.3.1 Frequency error.11
5.3.2 Effective radiated power.11
5.3.3 Maximum frequency deviation.12
5.3.4 Adjacent and alternate channel power .12
5.3.5 Radiated unwanted emission in the spurious domain .12
5.3.6 Spurious radiations.12
5.4 Other test specifications.12
5.4.1 Average usable sensitivity (speech, field strength).12
5.4.2 Co-channel rejection.12
5.4.3 Adjacent channel selectivity .12
5.4.4 Spurious response rejection .12
5.4.5 Intermodulation response rejection.12
5.4.6 Blocking or desensitization.12
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT).13
Annex B (informative): The EN title in the official languages .15
History .16

ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 296-2 V1.2.1 (2008-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC of the European Parliament and of
the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [i.1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 296-2 V1.2.1 (2008-07)
1 Scope
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference
and to make acceptable use of the available frequencies.
The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile
service, operating on radio frequen
...