EN 62343-1-2:2015

SLOVENSKI STANDARD
01-marec-2016
1DGRPHãþD
SIST EN 62343-1-2:2008
'LQDPLþQLPRGXOL7HKQLþQLVWDQGDUGLGHO1DVWDYOMLYLNRPSHQ]DWRUEDUYQH
GLVSHU]LMHEUH]NRQHNWRUMHY
Dynamic modules - Performance standards - Part 1-2: Tuneable chromatic dispersion
compensator (non-connectorized)
Ta slovenski standard je istoveten z: EN 62343-1-2:2015
ICS:
33.180.01 6LVWHPL]RSWLþQLPLYODNQLQD Fibre optic systems in
VSORãQR general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62343-1-2

NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2015
ICS 33.180.30 Supersedes EN 62343-1-2:2008
English Version
Dynamic modules - Part 1-2: Performance standards -
Tuneable chromatic dispersion compensator
(non-connectorized)
(IEC 62343-1-2:2015)
Modules dynamiques - Partie 1-2: Normes de performance - Dynamische Module - Teil 1-2: Betriebsverhaltensnormen -
Compensateur de dispersion chromatique réglable Einstellbarer Kompensator für chromatische Dispersion
(non connectorisé) (nicht mit Steckern versehen)
(IEC 62343-1-2:2015) (IEC 62343-1-2:2015)
This European Standard was approved by CENELEC on 2015-07-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62343-1-2:2015 E
European foreword
The text of document 86C/1315/FDIS, future edition 2 of IEC 62343-1-2, prepared by SC 86C "Fibre
optic systems and active devices” of IEC/TC 86 “Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN 62343-1-2:2015.

The following dates are fixed:
(dop) 2016-05-27
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2018-07-30
standards conflicting with the
document have to be withdrawn
This document supersedes EN 62343-1-2:2008. It constitutes a technical revision. This edition
includes the following significant technical changes with respect to the previous edition:
a) substantial addition of definitions and removal of type C performances.
b) change in the title to reflect standard terminology.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62343-1-2:2015 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

1)
IEC 62343-1 NOTE Harmonized as EN 62343-1 .
IEC 62343-1-3 NOTE Harmonized as EN 62343-1-3.

1)
At draft stage.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
Publication Year Title EN/HD Year

IEC 61300-1 -  Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
IEC 61300-2-14 -  Fibre optic interconnecting devices and EN 61300-2-14 -
passive components - Basic test and
measurement procedures -
Part 2-14: Tests - High optical power
IEC 61300-3-2 -  Fibre optic interconnecting devices and EN 61300-3-2 -
passive components - Basic test and
measurement procedures -
Part 3-2: Examinations and measurements
- Polarization dependent loss in a single-
mode fibre optic device
IEC 61300-3-29 -  Fibre optic interconnecting devices and EN 61300-3-29 -
passive components - Basic test and
measurement procedures -
Part 3-29: Examinations and
measurements - Spectral transfer
characteristics of DWDM devices
IEC 61300-3-32 -  Fibre optic interconnecting devices and EN 61300-3-32 -
passive components - Basic test and
measurement procedures -
Part 3-32: Examinations and
measurements - Polarisation mode
dispersion measurement for passive
optical components
IEC 61300-3-38 -  Fibre optic interconnecting devices and EN 61300-3-38 -
passive components - Basic test and
measurement procedures -
Part 3-38:Examinations and
measurements - Group delay, chromatic
dispersion and phase ripple
Publication Year Title EN/HD Year

IEC 61753-021-2 -  Fibre optic interconnecting devices EN 61753-021-2 -
and passive components performance
standard -
Part 021-2: Grade C/3 single-mode fibre
optic connectors for category C -
Controlled environment
IEC 62074-1 -  Fibre optic interconnecting devices and EN 62074-1 -
passive components - Fibre optic WDM
devices -
Part 1: Generic specification
IEC 62343 -  Dynamic modules - General and guidance EN 62343 -
ITU-T -  Transmission characteristics of optical - -
Recommendation components and subsystems
G.671
ITU-T -  Optical interfaces for multichannel systems - -
Recommendation with optical amplifiers
G.692
ITU-T G-series Optical system design and engineering - -
Recommendations - considerations
Supplement 39
IEC 62343-1-2 ®
Edition 2.0 2015-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Dynamic modules –
Part 1-2: Performance standards – Tuneable chromatic dispersion compensator

(non-connectorized)
Modules dynamiques –
Partie 1-2: Normes de performance – Compensateur de dispersion chromatique

réglable (non connectorisé)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.30 ISBN 978-2-8322-2771-8

– 2 – IEC 62343-1-2:2015 © IEC 2015
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references. 5
3 Terms and definitions . 6
4 Test . 7
4.1 General . 7
4.2 Module . 7
4.3 Spectral bands . 7
5 Test report. 8
6 Performance requirements . 8
6.1 Dimensions . 8
6.2 Sample size . 8
6.3 Test details and requirements . 8
Bibliography . 11

Table 1 – Spectral bands for single-mode systems (ITU-T G Suppl. 39) . 8
Table 2 – Test and requirements for type A (Multi/single channel type TDC with large
dispersion variable range) . 9
Table 3 – Test and requirements for type B (Multi/single channel type TDC with
standard dispersion variable range) . 10

IEC 62343-1-2:2015 © IEC 2015 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
Part 1-2: Performance standards – Tuneable chromatic
dispersion compensator (non-connectorized)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62343-1-2 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition published in 2007. It constitutes a
technical revision.
This edition includes the following significant t
...