EN 62561-5:2017

SLOVENSKI STANDARD
01-marec-2018
1DGRPHãþD
SIST EN 62561-5:2011
(OHPHQWLVLVWHPD]D]DãþLWRSUHGVWUHOR/36&GHO=DKWHYH]DPHULOQHRPDULFH
R]HPOMLOLQWHVQMHQMHL]RODFLMHSULR]HPOMLOLK
Lightning protection system components (LPSC) - Part 5: Requirements for earth
electrode inspection housings and earth electrode seals
Blitzschutzsystembauteile (LPSC) - Teil 5: Anforderungen an Revisionskästen und
Erderdurchführungen
Composants de système de protection contre la foudre (CSPF) - Partie 5: Exigences
pour les regards de visite et les joints d'étanchéité des électrodes de terre
Ta slovenski standard je istoveten z: EN 62561-5:2017
ICS:
91.120.40 =DãþLWDSUHGVWUHOR Lightning protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62561-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2017
ICS 29.020; 91.120.40 Supersedes EN 62561-5:2011
English Version
Lightning protection system components (LPSC) - Part 5:
Requirements for earth electrode inspection housings and earth
electrode seals
(IEC 62561-5:2017)
Composants de système de protection contre la foudre Blitzschutzsystembauteile (LPSC) - Teil 5: Anforderungen
(CSPF) - Partie 5: Exigences pour les regards de visite et an Revisionskästen und Erderdurchführungen
les joints d'étanchéité des électrodes de terre (IEC 62561-5:2017)
(IEC 62561-5:2017)
This European Standard was approved by CENELEC on 2017-09-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62561-5:2017 E
European foreword
The text of document 81/565/FDIS, future edition 2 of IEC 62561-5, prepared by IEC/TC 81, "Lightning
protection", was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
– latest date by which this document has to be (dop) 2018-06-01
implemented at national level
by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2020-12-01
with this document have to be withdrawn

This document supersedes EN 62561-5:2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 62561-5:2017 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 62305 (series) NOTE Harmonized as EN 62305 (series).

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 62305-3 -  Protection against lightning -- Part 3: EN 62305-3 -
Physical damage to structures and life
hazard
IEC 62561-5 ®
Edition 2.0 2017-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Lightning protection system components (LPSC) –

Part 5: Requirements for earth electrode inspection housings and earth

electrode seals
Composants de système de protection contre la foudre (CSPF) –

Partie 5: Exigences pour les regards de visite et les joints d'étanchéité

des électrodes de terre
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.020; 91.120.40 ISBN 978-2-8322-4636-8

– 2 – IEC 62561-5:2017 © IEC 2017
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Classification . 8
4.1 Earth electrode inspection housings . 8
4.2 Earth electrode seals . 8
5 Requirements . 8
5.1 General . 8
5.2 Installation instructions . 8
5.3 Earth electrode inspection housing . 8
5.4 Earth electrode seal . 8
5.5 Marking . 8
6 Tests . 9
6.1 General test conditions . 9
6.2 Earth electrode inspection housing . 9
6.2.1 General . 9
6.2.2 Load test . 9
6.3 Earth electrode seal test . 11
6.3.1 Earth electrode in watertight housing . 11
6.3.2 Earth electrode in or through watertight concrete . 11
6.4 Installation instructions . 13
6.4.1 General conditions for tests . 13
6.4.2 Acceptance criteria . 14
6.5 Marking . 14
6.5.1 General conditions for tests . 14
6.5.2 Acceptance criteria . 14
7 Electromagnetic compatibility (EMC) . 14
8 Structure and content of the test report . 14
8.1 General . 14
8.2 Report identification . 15
8.3 Specimen description . 15
8.4 Standards and references . 15
8.5 Test procedure . 15
8.6 Testing equipment, description . 15
8.7 Measuring instruments description . 16
8.8 Results and parameters recorded . 16
8.9 Statement of pass/fail . 16
Bibliography . 17

Figure 1 – Test arrangement for load test . 10
Figure 2 – Test arrangement for sealing test . 11

IEC 62561-5:2017 © IEC 2017 – 3 –
Figure 3 – Example for a test arrangement for depth of penetration of water under
pressure . 13

Table 1 – Parameters for concrete used for the test arrangement . 12

– 4 – IEC 62561-5:2017 © IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) –

Part 5: Requirements for earth electrode inspection housings
and earth electrode seals
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of t
...