Optical fibre cables - Part 1-306: Generic specification - Basic optical cable test procedures - Cable element test methods - Ribbon torsion, Method G6

IEC 60794-1-306: 2023 describes test procedures to verify the mechanical and functional integrity of the fibre ribbon structure. The test determines the capability of the ribbon to withstand torsion without delamination between optical fibre and ribbon bonding agent. This document applies to optical fibre ribbons in optical cables for use with telecommunication equipment and devices employing similar techniques, and to optical fibre ribbons in cables having a combination of both optical fibres and electrical conductors. This document is not applicable to partially-bonded ribbons. The method for partially-bonded ribbons is under consideration. Throughout the document, the wording "optical cable" can also include optical fibre units, microduct fibre units, etc. NOTE The environmental testing of optical fibre ribbon would be valuable for some applications. Useful information about suitable test methods can be found in the optical fibre standards IEC 60793-1-50, IEC 60793-1-51, IEC 60793‑1‑52, and IEC 60793-1-53. This document partially cancels and replaces IEC 60794‑1‑23:2019. This edition includes the following significant technical changes with respect to IEC 60794‑1‑23:2019: a) change the scope, not include partially-bonded ribbon; b) add some details to the procedure.

Lichtwellenleiterkabel - Teil 1-306: Fachgrundspezifikation - Grundlegende Prüfverfahren für optische Kabel - Prüfverfahren für Kabelelemente - Bändertorsion, Verfahren G6

Câbles à fibres optiques - Partie 1-306: Spécification générique - Procédures fondamentales d'essai des câbles optiques - Méthodes d'essai des éléments de câbles - Torsion du ruban, méthode G6

IEC 60794-1-306: 2023 décrit les procédures d'essais en vue de vérifier l'intégrité mécanique et fonctionnelle de la structure en rubans des fibres. L'essai vise à déterminer la capacité du ruban à résister à la torsion sans décollement interlaminaire entre la fibre optique et l'agent de fixation du ruban. Le présent document s’applique aux rubans de fibres optiques dans les câbles optiques destinés à être utilisés dans les équipements de télécommunications et les dispositifs qui utilisent des techniques similaires, ainsi qu'aux rubans de fibres optiques dans les câbles qui combinent à la fois des fibres optiques et des conducteurs électriques. Le présent document ne s’applique pas aux rubans collés partiellement. La méthode relative aux rubans collés partiellement est à l’étude. Dans tout le document, l'expression "câble optique" peut également inclure des assemblages de fibres optiques, des assemblages de fibres pour microconduits, etc. NOTE Les essais d’environnement appliqués au ruban de fibres optiques sont susceptibles d’être particulièrement utiles dans le cas de certaines applications. Des informations utiles liées aux méthodes d'essais appropriées sont fournies dans les normes relatives aux fibres optiques IEC 60793-1-50, IEC 60793-1-51, IEC 60793‑1‑52 et IEC 60793-1-53. Ce document annule et remplace partiellement l’IEC 60794‑1‑23:2019. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’IEC 60794‑1‑23:2019: a) modification du domaine d'application, non inclus le ruban collé partiellement; b) ajout de certaines précisions à la procédure

Optični kabli - 1-306. del: Splošna specifikacija - Osnovni preskusni postopki za optične kable - Preskusne metode za kabelske elemente - Zasuk traku, metoda G6 (IEC 60794-1-306:2023)

Standard IEC 60794-1-306: 2023 opisuje preskusne postopke za preverjanje mehanske in funkcionalne celovitosti strukture trakov iz vlaken. S preskusom se določi odpornost traku na zasuk brez razslojevanja med optičnim vlaknom in vezivnim sredstvom za trakove. Dokument se uporablja za trakove iz optičnih vlaken za uporabo s telekomunikacijsko opremo in napravami, ki uporabljajo podobne tehnike, ter trakove iz optičnih vlaken v kablih s kombinacijo optičnih vlaken in električnih vodnikov. Ta dokument se ne uporablja za delno vezane trakove. Metoda za delno vezane trakove je v pripravi. V dokumentu lahko izraz »optični kabel« vključuje tudi optične enote, mikrokanale itd. OPOMBA: Okoljsko preskušanje traku iz optičnih vlaken je lahko koristno za nekatere vrste uporabe. Koristne informacije o ustreznih preskusnih metodah so na voljo v standardih za optična vlakna IEC 60793-1-50, IEC 60793-1-51, IEC 60793‑1‑52 in IEC 60793-1-53. Dokument delno razveljavlja in nadomešča standard IEC 60794-1‑23:2019. Ta izdaja v primerjavi s standardom IEC 60794-1-23:2019 vključuje naslednje pomembne tehnične spremembe:
a) spremenjeno področje uporabe (ne zajema delno vezanih trakov);
b) dodanih je bilo nekaj podrobnosti v zvezi s postopkom.

General Information

Status
Published
Publication Date
26-Oct-2023
Current Stage
6060 - Document made available - Publishing
Start Date
27-Oct-2023
Due Date
23-Jun-2023
Completion Date
27-Oct-2023

Relations

Buy Standard

Standard
EN IEC 60794-1-306:2023
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2023
Optični kabli - 1-306. del: Splošna specifikacija - Osnovni preskusni postopki za
optične kable - Preskusne metode za kabelske elemente - Zasuk traku, metoda G6
(IEC 60794-1-306:2023)
Optical fibre cables - Part 1-306: Generic specification - Basic optical cable test
procedures - Cable element test methods - Ribbon torsion, Method G6 (IEC 60794-1-
306:2023)
Lichtwellenleiterkabel - Teil 1-306: Fachgrundspezifikation - Grundlegende Prüfverfahren
für optische Kabel - Prüfverfahren für Kabelelemente - Bändertorsion, Verfahren G6 (IEC
60794-1-306:2023)
Câbles à fibres optiques - Partie 1-306: Spécification générique - Procédures
fondamentales d'essai des câbles optiques - Méthodes d'essai des éléments de câbles -
Torsion du ruban, Méthode G6 (IEC 60794-1-306:2023)
Ta slovenski standard je istoveten z: EN IEC 60794-1-306:2023
ICS:
33.180.10 (Optična) vlakna in kabli Fibres and cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60794-1-306

NORME EUROPÉENNE
EUROPÄISCHE NORM October 2023
ICS 33.180.10 Supersedes EN IEC 60794-1-23:2019 (partially)
English Version
Optical fibre cables - Part 1-306: Generic specification - Basic
optical cable test procedures - Cable element test methods -
Ribbon torsion, Method G6
(IEC 60794-1-306:2023)
Câbles à fibres optiques - Partie 1-306: Spécification Lichtwellenleiterkabel - Teil 1-306: Fachgrundspezifikation -
générique - Procédures fondamentales d'essai des câbles Grundlegende Prüfverfahren für optische Kabel -
optiques - Méthodes d'essai des éléments de câbles - Prüfverfahren für Kabelelemente - Bändertorsion, Verfahren
Torsion du ruban, méthode G6 G6
(IEC 60794-1-306:2023) (IEC 60794-1-306:2023)
This European Standard was approved by CENELEC on 2023-10-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60794-1-306:2023 E

European foreword
The text of document 86A/2368/FDIS, future edition 1 of IEC 60794-1-306, prepared by SC 86A
"Fibres and cables" of IEC/TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 60794-1-306:2023.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2024-07-24
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-10-24
document have to be withdrawn
This document partially supersedes EN IEC 60794-1-23:2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60794-1-306:2023 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60793-1-50 NOTE Approved as EN 60793-1-50
IEC 60793-1-51 NOTE Approved as EN 60793-1-51
IEC 60793-1-52 NOTE Approved as EN 60793-1-52
IEC 60793-1-53 NOTE Approved as EN 60793-1-53
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60794-1-2 - Optical fibre cables - Part 1-2: Generic EN IEC 60794-1-2 -
specification - Basic optical cable test
procedures - General guidance
IEC 60794-1-306 ®
Edition 1.0 2023-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Optical fibre cables –
Part 1-306: Generic specification – Basic optical cable test procedures – Cable

element test methods – Ribbon torsion, Method G6

Câbles à fibres optiques –
Partie 1-306: Spécification générique – Procédures fondamentales d'essai des

câbles optiques – Méthodes d'essai des éléments de câbles – Torsion du ruban,

méthode G6
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.10  ISBN 978-2-8322-7519-1

– 2 – IEC 60794-1-306:2023 © IEC 2023
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General requirements . 6
5 Sample . 7
6 Apparatus . 7
7 Procedure . 8
8 Requirements . 8
9 Details to be specified . 8
Bibliography . 9

Figure 1 – Torsion test . 7

IEC 60794-1-306:2023 © IEC 2023 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL FIBRE CABLES –
Part 1-306: Generic specification – Basic optical cable test procedures –
Cable element test methods – Ribbon torsion, method G6

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.