Specifications for particular types of winding wires - Part 0-8: General requirements - Polyester glass-fibre wound unvarnished and fused, or resin or varnish impregnated, bare or enamelled rectangular copper wire

IEC 60317-0-8:2019 is available as IEC 60317-0-8:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60317-0-8:2019 specifies the general requirements of polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated bare, or grade 1 or grade 2 or enamelled rectangular copper winding wires. The range of nominal conductor dimensions is given in 4.1 and in the relevant specification sheet. This second edition cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - revision to the title of the standard indicating that the glass fibre covering is fused and unvarnished; - revision to subclause 3.2 adding winding wire requirements for the fibrous covering and a list of covering classifications; - revision to subclause 3.3 requirements for appearance; - revision to subclause 8.2, adherence test requirements. Keywords: insulated wires used for windings in electrical equipment

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-8: Allgemeine Anforderungen - Flachdrähte aus Kupfer, blank oder lackisoliert, mit unbeschichtetem Polyester-Glas-Fasergewebe umsponnen und verschmolzen oder mit Harz oder Lack imprägniert oder nicht imprägniert

Spécifications pour types particuliers de fils de bobinage - Partie 0-8: Exigences générales - Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre avec polyester fondues sans vernis, ou imprégnées de résine ou de vernis

IEC 60317-0-8:2019 est disponible sous forme de IEC 60317-0-8:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 60317-0-8:2019 spécifie les exigences générales pour les fils de bobinage de section rectangulaire en cuivre nus ou émaillés, soit de grade 1 soit de grade 2, guipés de fibres de verre avec polyester fondues, non vernies, ou imprégnées de résine ou de vernis. La gamme des dimensions nominales des conducteurs est donnée au 4.1 et dans la feuille de spécification correspondante. Cette deuxième édition annule et remplace la première édition parue en 2012. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - révision du titre de la norme indiquant que l'enveloppe de fibre de verre est fondue et sans vernis; - révision du paragraphe 3.2 comprenant l'ajout d'exigences pour les fils de bobinage pour l'enveloppe fibreuse et une liste de classifications d'enveloppes; - révision des exigences du paragraphe 3.3 relatives à l'aspect; - révision du paragraphe 8.2, exigences portant sur l'essai d’adhérence. Mots-clés: fils isolés utilisés pour les enroulements des appareils électriques

Specifikacije za posebne vrste navijalnih žic - 0-8. del: Splošne zahteve - Pravokotna profilna bakrena žica, gola ali emajlirana, obdana s steklenimi vlakni in poliestrom, impregniranimi s smolo ali lakom ali neimpregniranimi (IEC 60317-0-8:2019)

Ta evropski standard določa splošne zahteve za pravokotne profilne bakrene žice, gole ali emajlirane, obdane s steklenimi vlakni in poliestrom, impregniranimi s smolo ali lakom ali neimpregniranimi, razreda 1 ali 2. Obseg nazivnih mer kondenzatorja je podan v razdelku 4.1 in v ustrezni razpredelnici s specifikacijami.

General Information

Status
Published
Publication Date
17-Oct-2019
Withdrawal Date
23-Sep-2022
Technical Committee
Drafting Committee
Current Stage
6060 - Document made available - Publishing
Start Date
18-Oct-2019
Completion Date
18-Oct-2019

Relations

Buy Standard

Standard
EN IEC 60317-0-8:2020
English language
30 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST EN 60317-0-8:2012
Specifikacije za posebne vrste navijalnih žic - 0-8. del: Splošne zahteve -
Pravokotna profilna bakrena žica, gola ali emajlirana, obdana s steklenimi vlakni in
poliestrom, impregniranimi s smolo ali lakom ali neimpregniranimi (IEC 60317-0-
8:2019)
Specifications for particular types of winding wires - Part 0-8: General requirements -
Polyester glass-fibre wound unvarnished and fused, or resin or varnish impregnated,
bare or enamelled rectangular copper wire (IEC 60317-0-8:2019)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-8:
Allgemeine Anforderungen - Flachdrähte aus Kupfer, blank oder lackisoliert, mit
Polyesterglasgewebe umsponnen und mit Harz oder Lack imprägniert oder nicht
imprägniert (IEC 60317-0-8:2019)
Spécifications pour types particuliers de fils de bobinage - Partie 0-8: Exigences
générales - Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre
avec polyester, imprégnées ou non de vernis ou de résine (IEC 60317-0-8:2019)
Ta slovenski standard je istoveten z: EN IEC 60317-0-8:2019
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60317-0-8

NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2019
ICS 29.060.10 Supersedes EN 60317-0-8:2012 and all of its
amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 0-8:
General requirements - Polyester glass-fibre wound unvarnished
and fused, or resin or varnish impregnated, bare or enamelled
rectangular copper wire
(IEC 60317-0-8:2019)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-8: Exigences générales - Fil de section Wickeldrähten - Teil 0-8: Allgemeine Anforderungen -
rectangulaire en cuivre nu ou émaillé, guipé de fibres de Flachdrähte aus Kupfer, blank oder lackisoliert, mit
verre avec polyester fondues sans vernis, ou imprégnées unbeschichteten Polyesterglasgewebe umsponnen und
de résine ou de vernis verschmolzen oder mit Harz oder Lack imprägniert oder
(IEC 60317-0-8:2019) nicht imprägniert
(IEC 60317-0-8:2019)
This European Standard was approved by CENELEC on 2019-09-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-0-8:2019 E

European foreword
The text of document 55/1784/FDIS, future edition 2 of IEC 60317-0-8, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-06-24
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-09-24
document have to be withdrawn
This document supersedes EN 60317-0-8:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60317-0-8:2019 was approved by CENELEC as a
European Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60851 series Winding wires - Test methods - Part 4: Chemical EN 60851 series
properties
ISO 3 -  Preferred numbers - Series of preferred numbers - -

IEC 60317-0-8 ®
Edition 2.0 2019-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –

Part 0-8: General requirements – Polyester glass-fibre wound unvarnished

and fused, or resin or varnish impregnated, bare or enamelled rectangular

copper wire
Spécifications pour types particuliers de fils de bobinage –

Partie 0-8: Exigences générales – Fil de section rectangulaire en cuivre nu

ou émaillé, guipé de fibres de verre avec polyester fondues sans vernis, ou

imprégnées de résine ou de vernis

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-7204-6

– 2 – IEC 60317-0-8:2019 © IEC 2019
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and general notes on tests and appearance . 7
3.1 Terms and definition . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions. 9
4.1 Conductor dimensions . 9
4.2 Tolerance on conductor dimensions . 12
4.3 Rounding of corners . 12
4.4 Increase in dimensions due to the insulation . 12
4.5 Overall dimensions . 14
4.5.1 Nominal overall dimensions . 14
4.5.2 Minimum overall dimensions . 14
4.5.3 Maximum overall dimensions . 14
5 Electrical resistance . 14
6 Elongation . 14
7 Springiness . 14
8 Flexibility and adherence . 15
8.1 Mandrel winding test . 15
8.2 Adherence test . 15
8.2.1 Fibre covered bare wires . 15
8.2.2 Fibre covered enamelled wires . 15
9 Heat shock . 15
10 Cut-through . 15
11 Resistance to abrasion . 15
12 Resistance to solvents . 15
13 Breakdown voltage . 15
14 Continuity of insulation . 16
15 Temperature index . 16
16 Resistance to refrigerants . 16
17 Solderability . 16
18 Heat or solvent bonding . 16
19 Dielectric dissipation factor . 16
20 Resistance to transformer oil . 16
21 Loss of mass . 16
23 Pin hole test . 17
30 Packaging . 17

IEC 60317-0-8:2019 © IEC 2019 – 3 –
Annex A (informative) Nominal cross-sectional areas for preferred and intermediate
sizes . 18
Bibliography . 27

Table 1 – Nominal cross-sectional areas of preferred sizes . 11
Table 2 – Conductor tolerances . 12
Table 3 – Corner radii . 12
Table 4 – Increase in dimensions . 13
Table 5 – Elongation . 14
Table 6 – Mandrel winding . 15
Table 7 – Breakdown voltage . 16
Table A.1 – Nominal cross-sectional areas . 18

– 4 – IEC 60317-0-8:2019 © IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.