prEN ISO 8739

SLOVENSKI STANDARD
01-februar-2024
Vezni elementi - Zasekani zatiči z vzporednimi utori in pilotno točko - Diamantni
zatiči z utori po celotni dolžini (ISO/DIS 8739:2023)
Fasteners - Parallel grooved pins, with pilot point - Full-length diamond grooves (ISO/DIS
8739:2023)
Verbindungselemente - Zylinderkerbstifte mit Einführende - Diamant-Nut über die
gesamte Länge (ISO/DIS 8739:2023)
Fixations - Goupilles cannelées constantes, à bout pilote - Cannelures diamant sur toute
la longueur (ISO/DIS 8739:2023)
Ta slovenski standard je istoveten z: prEN ISO 8739
ICS:
21.060.50 Zatiči, žeblji Pins, nails
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 8739
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-11-27 2024-02-19
Fasteners — Parallel grooved pins, with pilot point — Full-
length diamond grooves
Fixations — Goupilles cannelées constantes, à bout pilote — Cannelures diamant sur toute la longueur
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8739:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 8739:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8739
ISO/TC 2 Secretariat: DIN
Voting begins on: Voting terminates on:

Fasteners — Parallel grooved pins, with pilot point — Full-
length diamond grooves
Fixations — Goupilles cannelées constantes, à bout pilote — Cannelures diamant sur toute la longueur
ICS: 21.060.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 8739:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 8739:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principles of grooved pins and assembly . 2
5 Dimensions .2
6 Requirements and reference International Standards . 5
7 Labelling on package .6
8 Designation . 6
Bibliography . 7
iii
ISO/DIS 8739:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners and by Technical Committee
CEN/TC 185, Fasteners in collaboration.
This third edition cancels and replaces the second edition (ISO 8739:1997) which has been technically
revised.
The main changes are as follows:
— terms and definitions, principles for grooved pins and assembly (including hole dimensions), control
of the expanded diameter d and pin straightness, mechanical and physical properties (including
shear resistance and hardness) and inspection which are common for all grooved pins (product
standards ISO 8739 to ISO 8747, ISO 13670 and ISO 13672) have been specified in the new reference
standard ISO 13669, general requirements;
— non-preferred diameters 1 mm, 3,5 mm, 7 mm, 9 mm, 14 mm and 18 mm have been added;
— values of expanded diameter d for steel pins have been slightly increased for the shortest length
range, and have been added for stainless steel pins;
— tolerances for the rounded end and values for the chamfered end have been added;
— stainless steel grades A2, A4, C1 and F1 have been added;
— other materials (such as hardened steels, brass, aluminium) are by agreement (see Table 3);
— specifications for labelling have been added as Clause 8.
Any feedback or questions on this document should be directed to the user's national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
DRAFT INTERNATIONAL STANDARD ISO/DIS 8739:2023(E)
Fasteners — Parallel grooved pins, with pilot point — Full-
length diamond grooves
1 Scope
This document specifies the characteristics of parallel grooved pins with pilot point and full-length
diamond grooves (with closed-end at the insertion side), in steel and stainless steel, and with nominal
diameter 1 mm to 25 mm.
These grooved pins are designed to fulfil the main following function:
— locking together two or more parts,
with the easiest installat
...