EN ISO 19288:2016

SLOVENSKI STANDARD
01-september-2016
'RGDMQLPDWHULDOL]DYDUMHQMHäLþQHHOHNWURGHPDVLYQHåLFHLQSDOLFH]DWDOLOQR
YDUMHQMHPDJQH]LMDLQPDJQH]LMHYLK]OLWLQ5D]YUVWLWHY,62
Welding consumables - Solid wire electrodes, solid wires and rods for fusion welding of
magnesium and magnesium alloys - Classification (ISO 19288:2016)
Schweißzusätze - Massivdrahtelektroden, Massivdrähte und Massivstäbe zum
Schmelzschweißen von Magnesium und Magnesiumlegierungen - Einteilung (ISO
19288:2016)
Produits consommables pour le soudage - Fils-électrodes pleins, fils pleins et baguettes
pleines pour le soudage par fusion du magnésium et des alliages de magnésium -
Classification (ISO 19288:2016)
Ta slovenski standard je istoveten z: EN ISO 19288:2016
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
77.120.20 Magnezij in magnezijeve Magnesium and magnesium
zlitine alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19288
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2016
EUROPÄISCHE NORM
ICS 25.160.20
English Version
Welding consumables - Solid wire electrodes, solid wires
and rods for fusion welding of magnesium and magnesium
alloys - Classification (ISO 19288:2016)
Produits consommables pour le soudage - Fils- Schweißzusätze - Massivdrahtelektroden,
électrodes pleins, fils pleins et baguettes pleines pour Massivdrähte und Massivstäbe zum Schmelzschweißen
le soudage par fusion du magnésium et des alliages de von Magnesium und Magnesiumlegierungen -
magnésium - Classification (ISO 19288:2016) Einteilung (ISO 19288:2016)
This European Standard was approved by CEN on 22 April 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19288:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 19288:2016) has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2016, and conflicting national standards
shall be withdrawn at the latest by December 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19288:2016 has been approved by CEN as EN ISO 19288:2016 without any modification.
INTERNATIONAL ISO
STANDARD 19288
First edition
2016-05-15
Welding consumables — Solid wire
electrodes, solid wires and rods for
fusion welding of magnesium and
magnesium alloys — Classification
Produits consommables pour le soudage — Fils-électrodes pleins, fils
pleins et baguettes pleines pour le soudage par fusion du magnésium
et des alliages de magnésium — Classification
Reference number
ISO 19288:2016(E)
©
ISO 2016
ISO 19288:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 19288:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Classification . 1
4 Symbols and requirements . 1
4.1 Symbol for the product . 1
4.2 Symbol for the chemical composition . 1
5 Mechanical properties . 2
6 Chemical analysis . 2
7 Rounding procedure . 2
8 Retest . 2
9 Technical delivery conditions . 2
10 Designation . 4
Annex A (informative) Explanation of classification symbols for chemical composition .5
ISO 19288:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
Requests for official interpretations of any aspect of this International Standard should be directed to
the Secretariat of ISO/TC 44/SC 3 via your national standards body. A complete listing of these bodies
can be found at www.iso.org.
iv © ISO 2016 – All rights reserved

ISO 19288:2016(E)
Introduction
This International Standard proposes a classification in order to designate solid wire electrodes, solid
wires and rods in terms of their chemical composition.
There is no unique relationship between the product form (solid wire electrodes, solid wires or rods)
and the welding process used (gas-shielded metal arc welding, tungsten inert gas arc welding, plasma
arc welding or laser beam welding). For this reason, solid wire electrodes, solid wires and rods may be
classified in terms of their chemical composition.
In this International Standard, the symbol of the welding process is not used because
a) different joining processes are performed with the same chemical component consumable, and
b) the producer is not able to determine the process symbol before shipping.
Mechanical properties of all-weld metal test specimens or welded joints will vary from those obtained
in production due to differences in welding procedure and the parent material. Mechanical properties
of all-weld metal or welded joints are consequently not specified.
INTERNATIONAL STANDARD ISO 19288:2016(E)
Welding consumables — Solid wire electrodes, solid wires
and rods for fusion welding of magnesium and magnesium
alloys — Classification
1 Scope
This International Standard specifies requirements for the classification of solid wire electrodes, solid
wires and rods for fusion welding of magnesium and magnesium alloys. The classification is based on
their chemical composition.
The compositions of solid wire electrodes for metal inert gas (MIG) welding are the same as solid wire
electrodes, solid wires and rods for tungsten inert gas (TIG) arc welding, plasma arc welding, laser
beam welding, laser-MIG hybrid welding and other fusion welding processes.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 544, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of
product, dimensions, tolerances and markings
ISO 14344, Welding consumables — Procurement of filler materials and fluxes
ISO 80000-1:2009, Quantities and units — Part 1: General. Corrected by ISO 80000-1:2009/Cor 1:2011
3 Classification
The classification is divided into two parts as follows:
a) the first part gives a symbol indicating the product to be identified (see 4.1);
b) the second part giv
...