EN 13329:2016+A1:2017/FprA2

SLOVENSKI STANDARD
SIST EN 13329:2016+A1:2017/oprA2:2020
01-julij-2020
Laminatne talne obloge - Elementi z zunanjo plastjo na osnovi aminoplastičnih
termostabilnih smol - Specifikacije, zahteve in preskusne metode
Laminate floor coverings - Elements with a surface layer based on aminoplastic
thermosetting resins - Specifications, requirements and test methods
Laminatböden - Elemente mit einer Deckschicht auf Basis aminoplastischer,
wärmehärtbarer Harze - Spezifikationen, Anforderungen und Prüfverfahren
Revêtements de sol stratifiés - Éléments dont la surface est à base de résines
aminoplastes thermodurcissables - Spécifications, exigences et méthodes d'essai
Ta slovenski standard je istoveten z: EN 13329:2016+A1:2017/prA2
ICS:
97.150 Talne obloge Floor coverings
SIST EN en
13329:2016+A1:2017/oprA2:2020
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN 13329:2016+A1:2017/oprA2:2020

SIST EN 13329:2016+A1:2017/oprA2:2020

DRAFT
EUROPEAN STANDARD
EN 13329:2016+A1:2017
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
July 2020
ICS 97.150
English Version
Laminate floor coverings - Elements with a surface layer
based on aminoplastic thermosetting resins -
Specifications, requirements and test methods
Revêtements de sol stratifiés - Éléments dont la surface Laminatböden - Elemente mit einer Deckschicht auf
est à base de résines aminoplastes thermodurcissables Basis aminoplastischer, wärmehärtbarer Harze -
- Spécifications, exigences et méthodes d'essai Spezifikationen, Anforderungen und Prüfverfahren
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 134.

This draft amendment A2, if approved, will modify the European Standard EN 13329:2016+A1:2017. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13329:2016+A1:2017/prA2:2020 E
worldwide for CEN national Members.

SIST EN 13329:2016+A1:2017/oprA2:2020
EN 13329:2016+A1:2017/prA2:2020 (E)
Contents Page
European foreword . 3
1 Modification to Clause 1, Scope . 4
2 Modification to term 3.3, substrate . 4
3 Modification to 4.2, Classification requirements, Table 2 . 4
4 Modification to Annex H, Determination of large ball impact resistance . 7
Annex H (normative) Determination of large ball impact resistance . 8
H.1 General. 8
H.2 Apparatus . 8
H.3 Procedure . 8

SIST EN 13329:2016+A1:2017/oprA2:2020
EN 13329:2016+A1:2017/prA2:2020 (E)
European foreword
This document (EN 13329:2016+A1:2017/prA2:2020) has been prepared by Technical Committee
CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13329:2016+A1:2017.
In comparison with the previous version EN 13329:2016+A1:2017 of the original edition EN
13329:2016, the new consolidated version EN 13329:2016+A2:2020 will contain the following
technical modifications:
— Scope: replacement of the last paragraph;
— term 3.3 substrate: replacement of the definition;
— Table 2: change the requirements and test method for impact resistance: small ball and addition of
d
footnote to table as clarification for testing, replacement of Table 2;
— Annex H: small ball test method has been deleted, replacement of Annex H.

SIST EN 13329:2016+A1:2017/oprA2:2020
EN 13329:2016+A1:2017/prA2:2020 (E)
1 Modification to Clause 1, Scope
Replace the last paragraph of the scope
“Laminate floor coverings are considered for domestic and commercial levels of use, including domestic
kitchens. This standard does not specify requirements relating to areas which are subjected to frequent
wetting, such as bathrooms, laundry rooms or saunas.”
with
“Laminate floor coverings are generally designed for floating installations and are considered for
domestic and commercial levels of use, including domestic kitchens. This document does not specify
requirements relating to the use in areas which are subjected to frequent wetting, such as bathrooms,
laundry rooms or saunas. In general laminate floor coverings can only be used in those areas when
authorized by the manufacturer and under conditions described in the manufacturer's installation
guidelines.”.
2 Modification to term 3.3, substrate
Replace the definition
”core material of the laminate floor covering”
with
“core material of the laminate floor covering made of wood, as defined in EN 13756, for at least 65 % in
mass”.
3 Modification to 4.2, Classification requirements, Table 2
...