prEN 13126-19

SLOVENSKI STANDARD
01-april-2025
Stavbno okovje - Okovje za okna in zastekljena vrata - Zahteve in preskusne
metode - 19. del: Drsne zapiralne naprave
Building hardware - Hardware for windows and door-height windows - Requirements and
test methods - Part 19: Sliding closing devices
Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und
Prüfverfahren - Teil 19: Schiebeverschlüsse (SCD)
Quincaillerie pour le bâtiment - Ferrures de fenêtres et portes-fenêtres - Exigences et
méthodes d'essai - Partie 19 : Dispositifs de verrouillage pour ouvrants coulissants
(SCD)
Ta slovenski standard je istoveten z: prEN 13126-19
ICS:
91.190 Stavbna oprema Building accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2025
ICS 91.190 Will supersede EN 13126-19:2011
English Version
Building hardware - Hardware for windows and door-
height windows - Requirements and test methods - Part
19: Sliding closing devices
Quincaillerie pour le bâtiment - Ferrures de fenêtres et Baubeschläge - Beschläge für Fenster und Fenstertüren
portes-fenêtres - Exigences et méthodes d'essai - Partie - Anforderungen und Prüfverfahren - Teil 19:
19 : Dispositifs de verrouillage pour ouvrants Schiebeverschlüsse (SCD)
coulissants (SCD)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 33.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13126-19:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Classification. 9
4.1 General. 9
4.2 Durability (1 – first box) . 9
4.3 Mass (2 – second box) . 9
4.4 Corrosion resistance (3 – third box) . 9
4.5 Test sizes – Size limitations (4 – fourth box). 9
4.6 Type of hardware (5 – fifth box) . 9
4.7 Secured position (6 – sixth box) . 9
4.8 Example of classification for sliding closing devices . 10
5 Requirements . 10
5.1 Dangerous substances. 10
5.2 Mechanical resistance . 10
5.3 Durability . 11
5.4 Requirement for a secured position | key-operated profile cylinder (if applicable) . 11
5.4.1 Durability test of a locking mechanism . 11
5.4.2 Torque resistance of the locking mechanism / solid fixing . 11
5.5 Static load test . 11
5.6 Corrosion resistance . 12
6 Test equipment and preparation of the test . 12
6.1 Test rig . 12
6.2 Specimen . 12
6.3 Mounting of the specimen. 12
7 Test procedure . 12
7.1 Samples . 12
7.2 Durability test on a SCD . 13
7.2.1 General. 13
7.2.2 Durability test on a SCD manual action . 13
7.2.3 Durability test on a SCD automatic action . 14
7.2.4 Acceptance criteria. 14
7.3 Tests of the mechanism of an optional secured position (if applicable) . 15
7.3.1 Durability test for a locking mechanism . 15
7.3.2 Torque resistance of the locking mechanism / Solid fixing test . 15
7.4 Static load test . 15
7.5 Corrosion resistance . 15
8 Marking . 16
Annex A (informative) Test assembly . 17
Annex B (informative) SCDs and operating forces . 20
Annex C (informative) Flow chart of test procedure . 21
Bibliography . 22
European foreword
This document (prEN 13126-19:2025) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
The performance tests incorporated in this document are considered to be reproducible and as such will
provide a consistent and objective assessment of the performance of these products throughout CEN
Member States.
This document will supersede EN 13126-19:2011.
In comparison with the previous edition, the following technical modifications have been made:
— EN 13126-19 now is independent from EN 13126-1; all necessary information is included without
the need of any further information from EN 13126-1;
— several editorial changings in the wording for a better understanding;
— new terms added under 3.5 to 3.15'
— under 4.1 classification system changed completely
— former digit 1 (Category of use) is now box 1 for the grade of cycles for the durability test
— former digit 3 (Mass) is now box 2
— former digit 4 (Corrosion resistance) is now box 3
— former digit 5 (Safety in use) is now box 4 for the test sizes
— former digit 6 (Corrosion resistance) is now box 3
— former digit 7 (Security) was deleted
— former digit 8 (Applicable part) is now box 5 for the type of hardware
— former digit 9 (Test sizes) is now box 4
— new box 6 for information on an optional secured position
— under 4.8 new examples added for a classification
— under 5.1 new text for dangerous substances added
— under 5.3 new grades H1 to H3 for the cycles for the durability test defined
— under 5.4 requirements added for an optional secured position with a key-operated profile cylinder
— under 5.4.1 grades for a durability test of a locking system added
— under 5.4.2 requirements for torque resistance of the locking mechanism added
— static load test is now under 5.5
— new text for the Corrosion resistance under 5.6
— several subclauses under 6. Test equipment and preparation of the test added; 6.1 Test rig, 6.2
Specimen, 6.3 Mounting of specimen
— subclause 7.1 Samples revised
— subclauses 7.2.2 durability test on a SCD manual action an 7.2.3 durability test on a SCD manual
action added
— complete subclause 7.3 Test of the mechanism of an optional secured position (if applicable) added
— in Annex A new figures integrated
EN 13126 consists of the following parts:
— EN 13126-1, Building hardware — Hardware for windows and door height windows — Requirements
and test methods — Part 1: Requirements common to all types of hardware;
— EN 13126-2, Building hardware — Hardware for windows and door height windows — Requirements
and test methods — Part 2: Window fastener handles;
— EN 13126-3, Building hardware — Hardware for windows and door-height windows — Requirements
and test methods — Part 3: Handles, primarily for Tilt and Turn, Tilt-First and Turn-Only hardware;
— EN 13126-4, Building hardware — Requirements and test methods for windows and door height
windows — Part 4: Espagnolettes;
— EN 13126-5, Building hardware — Hardware for windows and door height windows — Requirements
and test methods — Part 5: Devices that restrict the opening of windows and door height windows;
— EN 13126-6, Building hardware — Hardware for windows and door height windows — Requirements
and test methods — Part 6: Variable geometry stay hinges (with or without a friction stay);
— EN 13126-7, Building hardware — Requirements and test methods for windows and door height
windows — Part 7: Finger catches;
— EN 13126-8, Building hardware — Hardware for windows and door height windows — Part 8:
Requirements and test methods for tilt and turn, Tilt-First and Turn-Only hardware;
— EN 13126-9, Building hardware — Requirements and test methods for windows and door height
windows — Part 9: Hardware for horizontal and vertical pivot windows;
— EN 13126-10, Building hardware — Requirements and test methods for windows and door height
windows — Part 10: Arm-balancing systems;
— EN 13126-11, Building hardware — Requirements and test methods for windows and door height
windows — Part 11: Top hung projecting reversible hardware;
— EN 13126-12, Building hardware — Requirements and test methods for windows and door height
windows — Part 12: Side hung projecting reversible hardw
...