EN ISO 8504-2:2019

SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST EN ISO 8504-2:2002
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Postopki
priprave površine - 2. del: Peskanje z abrazivi (ISO 8504-2:2019)
Preparation of steel substrates before application of paints and related products -
Surface preparation methods - Part 2: Abrasive blast-cleaning (ISO 8504-2:2019)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Verfahren für die Oberflächenvorbereitung - Teil 2: Strahlen (ISO 8504-2:2019)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Méthodes de préparation des subjectiles - Partie 2: Décapage par projection
d'abrasif (ISO 8504-2:2019)
Ta slovenski standard je istoveten z: EN ISO 8504-2:2019
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 8504-2
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2019
EUROPÄISCHE NORM
ICS 25.220.10 Supersedes EN ISO 8504-2:2001
English Version
Preparation of steel substrates before application of paints
and related products - Surface preparation methods - Part
2: Abrasive blast-cleaning (ISO 8504-2:2019)
Préparation des subjectiles d'acier avant application de Vorbereitung von Stahloberflächen vor dem Auftragen
peintures et de produits assimilés - Méthodes de von Beschichtungsstoffen - Verfahren für die
préparation des subjectiles - Partie 2: Décapage par Oberflächenvorbereitung - Teil 2: Strahlen (ISO 8504-
projection d'abrasif (ISO 8504-2:2019) 2:2019)
This European Standard was approved by CEN on 30 September 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8504-2:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 8504-2:2019) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2020, and conflicting national standards shall be
withdrawn at the latest by May 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8504-2:2001.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8504-2:2019 has been approved by CEN as EN ISO 8504-2:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 8504-2
Third edition
2019-10
Preparation of steel substrates before
application of paints and related
products — Surface preparation
methods —
Part 2:
Abrasive blast-cleaning
Préparation des subjectiles d'acier avant application de peintures et
de produits assimilés — Méthodes de préparation des subjectiles —
Partie 2: Décapage par projection d'abrasif
Reference number
ISO 8504-2:2019(E)
©
ISO 2019
ISO 8504-2:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 8504-2:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abrasives . 2
4.1 Materials and types . 2
4.2 General requirements . 4
4.2.1 Technical . 4
4.2.2 Health and safety . 4
4.3 Selection considerations . 4
5 Abrasive blast-cleaning methods . 5
5.1 Dry abrasive blast-cleaning . 5
5.1.1 Centrifugal abrasive blast-cleaning . 5
5.1.2 Compressed-air abrasive blast-cleaning . 6
5.1.3 Vacuum or suction-head abrasive blast-cleaning . 6
5.2 Wet abrasive blast-cleaning . 7
5.2.1 General. 7
5.2.2 Moisture-injection abrasive blast-cleaning (compressed-air moisture-
injection abrasive blast- cleaning) . 7
5.2.3 Compressed-air wet abrasive blast-cleaning . 8
5.2.4 Slurry blast-cleaning . 8
5.2.5 Pressurized-liquid blast-cleaning . 9
6 Procedure. 9
6.1 Preparation before blast-cleaning . 9
6.2 Blast-cleaning . 9
6.3 After blast-cleaning .10
7 Assessment of the blast-cleaned surface.10
Bibliography .11
ISO 8504-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 12, Preparation of steel substrates before application of paints and related products.
This third edition cancels and replaces the second edition (ISO 8504-2:2000), which has been technically
revised. The main changes compared to the previous edition are as follows:
— update of Clause 2, normative references;
— editorial revision.
A list of all parts in the ISO 8504 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2019 – All rights reserved
...