prEN ISO 11126-1

SLOVENSKI STANDARD
01-november-2024
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov -
Specifikacije za nekovinske granulate za peskanje - 1. del: Splošni uvod in
razvrstitev (ISO/DIS 11126-1:2024)
Preparation of steel substrates before application of paints and related products -
Specifications for non-metallic blast-cleaning abrasives - Part 1: General introduction and
classification (ISO/DIS 11126-1:2024)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Anforderungen an nichtmetallische Strahlmittel - Teil 1: Allgemeine Einleitung und
Einteilung (ISO/DIS 11126-1:2024)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Spécifications pour abrasifs non métalliques destinés à la préparation par
projection - Partie 1: Introduction générale et classification (ISO/DIS 11126-1:2024)
Ta slovenski standard je istoveten z: prEN ISO 11126-1
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 11126-1
ISO/TC 35/SC 12
Preparation of steel substrates
Secretariat: BSI
before application of paints and
Voting begins on:
related products — Specifications
2024-10-09
for non-metallic blast-cleaning
Voting terminates on:
abrasives —
2025-01-01
Part 1:
General introduction and
classification
Préparation des subjectiles d'acier avant application de peintures
et de produits assimilés — Spécifications pour abrasifs non
métalliques destinés à la préparation par projection —
Partie 1: Introduction générale et classification
ICS: 25.220.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 11126-1:2024(en)
DRAFT
ISO/DIS 11126-1:2024(en)
International
Standard
ISO/DIS 11126-1
ISO/TC 35/SC 12
Preparation of steel substrates
Secretariat: BSI
before application of paints and
Voting begins on:
related products — Specifications
for non-metallic blast-cleaning
Voting terminates on:
abrasives —
Part 1:
General introduction and
classification
Préparation des subjectiles d'acier avant application de peintures
et de produits assimilés — Spécifications pour abrasifs non
métalliques destinés à la préparation par projection —
Partie 1: Introduction générale et classification
ICS: 25.220.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 11126-1:2024(en)
ii
ISO/DIS 11126-1:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
4.1 Abrasive type .2
4.2 Initial particle shape .2
4.3 Particle size range .2
5 Designation of abrasives . 3
6 Identification and marking. 3
Annex A (informative) International Standards for metallic and non-metallic blast-cleaning
abrasives . 4
Bibliography . 6

iii
ISO/DIS 11126-1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL:
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 12,
Preparation of steel substrates before application of paints and related products.
This third edition cancels and replaces the second edition (ISO 11126-1:2018), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Table 1, Table 2 and Annex A have been technically revised.
A list of all parts in the ISO 11126 series can be found on t
...