ASTM F1210-19

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1210 − 14 F1210 − 19
Standard Guide for
Ecological Considerations for the Use of Oil Spill
Dispersants in Freshwater and Other Inland Environments,
1
Lakes and Large Water Bodies
This standard is issued under the fixed designation F1210; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of
minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and
socioeconomic factors are not considered, although these and other factors are often important in spill response.
1.2 Spill responders have available several means to control or clean up spilled oil. In this guide, the use of dispersants is given
equal consideration with other spill countermeasures. It is not considered as a “last resort” after all other methods have failed.
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences
between individual dispersants or between different oil products are not considered.
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the
use of dispersants primarily to protect habitats from impact (or to minimize impacts).
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of
dispersants to subsurface waters.
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.
1.7 This guide does not address getting regulatory approval.
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.10 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
F2532 Guide for Determining Net Environmental Benefit of Dispersant Use
3. Significance and Use
3.1 This guide is meant to aid local and regional response teams who may use it during spill response planning and spill events.
3.2 This guide should be adapted to site specific circumstance.
4. Environment Covered—Lakes and Large Water Bodies
4.1 Lakes and large water bodies are major fresh water features that are a significant part of major water systems. They have
a dynamic near-shore ecology, and a wide mixture of animal and plants species. In northern regions, these water bodies may be
1
This guide is under the jurisdiction of ASTM Committee F20 on Hazardous Substances and Oil Spill Responseand is the direct responsibility of Subcommittee F20.13
on Treatment.
Current edition approved March 1, 2014Aug. 1, 2019. Published March 2014August 2019. Originally approved in 1989. Last previous edition approved in 20082014 as
F1210 – 08.F1210 –14. DOI: 10.1520/F1210-14.10.1520/F1210-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1210 − 19
partly or completely ice-covered during part of the year but will not freeze to the bottom. Commercially important fishing and
recreational activities are frequently associated with these water bodies.
4.2 While most of these bodies are naturally occurring and exist during the most of the year, some may be man-made.
4.3 The characteristics of these water bodies are:
4
...

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1210 − 19
Standard Guide for
Ecological Considerations for the Use of Oil Spill
Dispersants in Freshwater and Other Inland Environments,
1
Lakes and Large Water Bodies
This standard is issued under the fixed designation F1210; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
1.1 This guide covers the use of oil spill dispersants to assist
1.10 This international standard was developed in accor-
in the control of oil spills. The guide is written with the goal of
dance with internationally recognized principles on standard-
minimizing the environmental impacts of oil spills; this goal is
ization established in the Decision on Principles for the
the basis on which the recommendations are made. Aesthetic
Development of International Standards, Guides and Recom-
and socioeconomic factors are not considered, although these
mendations issued by the World Trade Organization Technical
and other factors are often important in spill response.
Barriers to Trade (TBT) Committee.
1.2 Spill responders have available several means to control
or clean up spilled oil. In this guide, the use of dispersants is
2. Referenced Documents
given equal consideration with other spill countermeasures. It
2
2.1 ASTM Standards:
is not considered as a “last resort” after all other methods have
F2532 Guide for Determining Net Environmental Benefit of
failed.
Dispersant Use
1.3 This is a general guide only. Oil, as used in this guide,
3. Significance and Use
includes crude oils and refined petroleum products. Differences
between individual dispersants or between different oil prod-
3.1 This guide is meant to aid response teams who may use
ucts are not considered.
it during spill response planning and spill events.
1.4 The guide is organized by habitat type, for example,
3.2 This guide should be adapted to site specific circum-
small ponds and lakes, rivers and streams, and land. It
stance.
considers the use of dispersants primarily to protect habitats
from impact (or to minimize impacts).
4. Environment Covered—Lakes and Large Water
Bodies
1.5 This guide applies only to freshwater and other inland
environments. It does not consider the direct application of
4.1 Lakes and large water bodies are major fresh water
dispersants to subsurface waters.
features that are a significant part of major water systems. They
have a dynamic near-shore ecology, and a wide mixture of
1.6 In making dispersant use decisions, appropriate govern-
animal and plants species. In northern regions, these water
ment authorities should be consulted as required by law.
bodies may be partly or completely ice-covered during part of
1.7 This guide does not address getting regulatory approval.
the year but will not freeze to the bottom. Commercially
1.8 The values stated in SI units are to be regarded as important fishing and recreational activities are frequently
standard. No other units of measurement are included in this associated with these water bodies.
standard.
4.2 While most of these bodies are naturally occurring and
1.9 This standard does not purport to address all of the
exist during most of the year, some may be man-made.
safety concerns, if any, associated with its use. It is the
4.3 The characteristics of these water bodies are:
responsibility of the user of this standard to establish appro-
4.3.1 Open water area greater than 10 hectares,
4.3.2 Water depths in excess of 1.5 m,
1
This guide is under the jurisdiction of ASTM Committee F20 on Hazardous
Substances and Oil Spill Responseand is the direct responsibility of Subcommittee
2
F20.13 on Treatment. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2019. Published August 2019. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1989. Last previous edition approved in 2014 as F1210 –14. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F1210-19. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1210 − 19
4.3.3 Soft or hard bottom with a low organic content except adverse effects of spilled oil on certain biological species at the
in shallow water areas, expense of other components of the ecosystem (14).
4.3.4 A well defined inlet or outlet, or both, and
6.2 Guide F2532 sh
...