ASTM F1267-06
(Specification)Standard Specification for Metal, Expanded, Steel
Standard Specification for Metal, Expanded, Steel
SCOPE
1.1 This specification covers expanded metal.
1.1.1 Expanded metal covered by this specification is intended for a variety of applications.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only and may be approximate.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 1267 – 06
Standard Specification for
1
Metal, Expanded, Steel
This standard is issued under the fixed designation F 1267; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy,
High-Strength Low-Alloy with Improved Formability, and
1.1 This specification covers expanded metal.
Ultra-High Strength
1.1.1 Expanded metal covered by this specification is in-
3
2.2 SAE Standard:
tended for a variety of applications.
SAE J 1086 Metals and Alloys in the Unified Numbering
1.2 The values stated in inch-pound units are to be regarded
System
as the standard. The values given in parentheses are for
4
2.3 Military Standards:
information only and may be approximate.
MIL-C-16173 Corrosion Preventive Compound, Solvent
1.3 The following precautionary caveat pertains only to the
Cutback, Cold-Application
test methods portion, Section 10, of this specification. This
MIL-STD-105 Sampling Procedures and Tables for Inspec-
standard does not purport to address all of the safety problems
tion by Attributes
associatedwithitsuse.Itistheresponsibilityoftheuserofthis
standard to establish appropriate safety and health practices
3. Classification
and determine the applicability of regulatory limitations prior
3.1 Expanded metal shall be of the following types, classes,
to use.
and grades as specified (see 4.1.2).
2. Referenced Documents 3.2 Type:
2
3.2.1 Type I—Expanded (see Fig. 1).
2.1 ASTM Standards:
3.2.2 Type II—Expanded and flattened (see Fig. 2).
A 123/A 123M Specification for Zinc (Hot-Dip Galva-
3.3 Class:
nized) Coatings on Iron and Steel Products
3.3.1 Class 1—Uncoated.
A 167 Specification for Stainless and Heat-Resisting
3.3.2 Class 2—Hot-dip zinc-coated (galvanized).
Chromium-Nickel Steel Plate, Sheet, and Strip
3.3.3 Class 3—Corrosion-resisting steel.
A 176 Specification for Stainless and Heat-Resisting Chro-
3.4 Grade:
mium Steel Plate, Sheet, and Strip
3.4.1 Grade A—0.0025 in. (0.06 mm) minimum coating
A 666 Specification for Annealed or Cold-Worked Austen-
thickness.
itic Stainless Steel Sheet, Strip, Plate, and Flat Bar
3.4.2 Grade B—0.0012 in. (0.03 mm) minimum coating
A 700 Practices for Packaging, Marking, and Loading
thickness.
Methods for Steel Products for Shipment
A 1008/A 1008M Specification for Steel, Sheet, Cold-
4. Ordering Information
Rolled, Carbon, Structural, High-Strength Low-Alloy,
4.1 Orders for material under this specification shall include
High-Strength Low-Alloy with Improved Formability, So-
the following information, as required, to describe the material
lution Hardened, and Bake Hardenable
adequately:
A 1011/A 1011M Specification for Steel, Sheet and Strip,
4.1.1 ASTM designation,
4.1.2 Type, class, and grade of steel required (see 3.1),
1 4.1.3 Material required (see 5.1),
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.19 on Steel Sheet and Strip.
Current edition approved Oct. 1, 2006. Published October 2006. Originally
3
approved in 1989. Last previous edition approved in 2001 as F 1267 – 01. Available from Society of Automotive Engineers (SAE), 400 Commonwealth
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Dr., Warrendale, PA 15096-0001, http://www.sae.org.
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM AvailablefromManufacturersStandardizationSocietyoftheValveandFittings
Standards volume information, refer to the standard’s Document Summary page on Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http://www.mss-
the ASTM website. hq.com.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F1267–06
4.1.5 Length, width, and thickness of uncoated mesh, and
weight per square foot uncoated (see Tables 1-4),
4.1.6 Size of sheet required, if other than sizes specified in
6.1,
4.1.7 Whether or not sheets from which samples have been
selected for coating thickness test may be included as part of
material shipped (see 9.1.2), and
4.1.8 Optional requirements, if any (see Supplementary
Requirements S1 through S3).
FIG. 1 Type I, Expanded
5. Materials and Manufacture
5.1 Expanded metal shall be made from Commercial Steel
(CS Type B) carbon steel sheets as specified in Specifications
A 1008/
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.