Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

SCOPE
1.1 This test method covers determination of the density (see Note 1) of freshly mixed concrete and gives formulas for calculating the yield, cement content, and air content of the concrete. Yield is defined as the volume of concrete produced from a mixture of known quantities of the component materials.
1.2 The values stated in either inch-pound or SI units shall be regarded separately as standard. The SI units are shown in brackets. The values stated might not be exact equivalents; therefore each system must be used independently of the other.Note 0
Unit weight was the previous terminology used to describe the property determined by this test method, which is mass per unit volume.
1.3 The text of this test method references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of this test method.

General Information

Status
Historical
Publication Date
14-Aug-2007
Current Stage
Ref Project

Relations

Buy Standard

Standard
ASTM C138/C138M-07 - Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
American Association State
Designation:C138/C138M–07 Highway and Transportation Officials Standard
AASHTO No.: T121
Standard Test Method for
Density (Unit Weight), Yield, and Air Content (Gravimetric)
1
of Concrete
This standard is issued under the fixed designation C 138/C 138M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
A = air content (percentage of voids) in the concrete
1.1 This test method covers determination of the density
3 3
C = actual cement content, lb/yd or kg/m
(see Note 1) of freshly mixed concrete and gives formulas for
C = mass of cement in the batch, lb or kg
b
calculating the yield, cement content, and air content of the
3 3
D = density (unit weight) of concrete, lb/ft or kg/m
concrete. Yield is defined as the volume of concrete produced
M = totalmassofallmaterialsbatched,lborkg(seeNote
from a mixture of known quantities of the component materi-
3)
als.
M = mass of the measure filled with concrete, lb or kg
c
1.2 The values stated in either inch-pound or SI units shall
M = mass of the measure, lb or kg
m
be regarded separately as standard. The SI units are shown in
R = relative yield
y
brackets. The values stated might not be exact equivalents;
T = theoretical density of the concrete computed on an
3 3
therefore each system must be used independently of the other.
airfree basis, lb/ft or kg/m (see Note 2)
3
Y = yield, volume of concrete produced per batch, yd or
NOTE 1—Unit weight was the previous terminology used to describe
3
the property determined by this test method, which is mass per unit m
volume. Y = volume of concrete which the batch was designed to
d
3 3
produce, yd or m
1.3 The text of this test method references notes and
3
Y = volume of concrete produced per batch, ft
f
footnotes that provide explanatory information. These notes
V = total absolute volume of the component ingredients
and footnotes (excluding those in tables) shall not be consid-
3 3
in the batch, ft or m
ered as requirements of this test method.
3 3
V = volume of the measure, ft or m
m
2. Referenced Documents
NOTE 2—The theoretical density is, customarily, a laboratory determi-
2
nation, the value for which is assumed to remain constant for all batches
2.1 ASTM Standards:
made using identical component ingredients and proportions. It is calcu-
C 29/C 29M Test Method for Bulk Density (“Unit Weight”)
lated from the following equation:
and Voids in Aggregate
T 5 M/V (1)
C 150 Specification for Portland Cement
C 172 Practice for Sampling Freshly Mixed Concrete
The absolute volume of each ingredient in cubic feet is equal to the
C 188 Test Method for Density of Hydraulic Cement
quotient of the mass of that ingredient divided by the product of its
C 231 Test Method for Air Content of Freshly Mixed
specific gravity times 62.4. The absolute volume of each ingredient in
Concrete by the Pressure Method
cubic metres is equal to the mass of the ingredient in kilograms divided by
1000 times its specific gravity. For the aggregate components, the bulk
3. Terminology
specific gravity and mass should be based on the saturated, surface-dry
condition. For cement, the actual specific gravity should be determined by
3.1 Symbols:
Test Method C 188. A value of 3.15 may be used for cements manufac-
tured to meet the requirements of Specification C 150.
1 NOTE 3—The total mass of all materials batched is the sum of the
This test method is under the jurisdiction of ASTM Committee C09 on
masses of the cement, the fine aggregate in the condition used, the coarse
Concrete and ConcreteAggregates and is the direct responsibility of Subcommittee
aggregate in the condition used, the mixing water added to the batch, and
C09.60 on Testing Fresh Concrete.
Current edition approved Aug. 15, 2007. Published September 2007. Originally any other solid or liquid materials used.
approved in 1938. Last previous edition approved in 2001 as C 138/C 138M – 01a.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C138/C138M–07
3
4. Apparatus measures of 0.5 ft [14 L] or smaller, and a mallet having a
mass of 2.25 6 0.50 lb [1000 6 2
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.