ASTM F2012-18

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2012 − 16 F2012 − 18
Standard Consumer Safety Performance Specification for
1
Stationary Activity Centers
This standard is issued under the fixed designation F2012; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety performance specification is intended to mitigate potential safety hazards
associated with a child’s use of a stationary activity center and thereby minimize the risk of injury or
death. The specific hazards addressed by this specification are seat strength to support the occupant,
product tip over, openings for finger entrapment and small parts.
1. Scope
1.1 This consumer safety performance specification covers performance requirements, test methods and marking requirements
to promote safe use of a stationary activity center by an occupant.
1.2 This consumer safety performance specification is intended to minimize the risk of incidents to an occupant resulting from
normal use and reasonably foreseeable misuse or abuse of a stationary activity center.
1.3 No stationary activity center produced after the approval date of this consumer safety performance specification shall, either
by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.4 This consumer safety performance specification is not intended to address incidents and injuries resulting from the
interaction of other persons with the child occupant in the stationary activity center or the incidents resulting from abuse and
misuse by children able to walk.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this consumer safety performance
specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and
determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D3359 Test Methods for Rating Adhesion by Tape Test
F963 Consumer Safety Specification for Toy Safety
3
2.2 Federal Regulations:
16 CFR 1303 Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint
16 CFR 1500 Hazardous Substances Act Regulations including sections:
1500.48 Technical Requirements for Determining a Sharp Point in Toys or Other Articles Intended for Use by Children Under
Eight Years of Age
1
This consumer safety performance specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee
F15.17 on Carriages, Strollers, Walkers and Stationary Activity Centers.
Current edition approved April 15, 2016March 1, 2018. Published May 2016March 2018. Originally approved in 2000. Last previous edition approved in 20132016 as
F2012 – 13.F2012 – 16. DOI: 10.1520/F2012-16.10.1520/F2012-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Superintendent of Documents, US Government Printing Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2012 − 18
1500.49 Technical Requirements for Determining a Sharp Metal or Glass Edge in Toys or Other Articles Intended for Use by
Children Under Eight Years of Age
1500.50-.52 Test Methods for Simulating Use and Abuse of Toys and Other Articles Intended for Use by Children
16 CFR 1501 M
...