ASTM F2755-22

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2755 − 14 F2755 − 22
Standard Safety Specification for
1
CautionarySafety Labeling of Inflatable Air Mattresses
This standard is issued under the fixed designation F2755; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Since 20022010 (until Jan. 1, 2008Jan. 1, 2021), the Consumer Product Safety Commission (CPSC)
has received reports of 16 tragic 83 deaths, mostly infants younger than 8 months of age, who were
placed to sleep on air mattresses. Eleven suffocated in a facedown position on anForty-two (42) were
co-sleeping, 25 suffocated on the air mattress, and five16 died as a result of suffocation after falling
into gaps between the air mattress and bed frame or the air mattress and adjacent furniture or wall.
1. Scope
1.1 This safety specification covers safety requirements aimed at providing cautionary labeling information for safer provides
safety labeling requirements for use of inflatable air mattresses (also known as “air beds,” collectively referred to herein as
“inflatable air mattresses”). The intent of this safety specification is to reduce child (infant) injuries and fatalities caused by
suffocation on inflatable air mattresses.“product”).
1.2 The intent of this safety specification is to reduce infant and child deaths and injuries caused by suffocation and entrapment
on inflatable air mattresses.
1.3 This safety specification covers all size inflatable air mattresses—including product sizes, including, but not limited to, full,
queen, king, and twin sizes.
1.4 This safety specification covers products intended for indoor and outdoor use, including camping and recreational uses.
1.5 This safety specification does not cover inflatable air mattresses products designed specifically for use in Durable Infant
Products.and Toddler Products (such as play yards, cribs, non-full-size cribs, etc.).
1.4 This safety specification is intended to reduce entrapment hazards to children and risk of suffocation to infants up to and
including age 15 months.
1.5 This safety specification includes inflatable air mattresses intended for recreational, camping, and other indoor and outdoor
uses.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1
This specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee F15.63 on Inflatable Air
Mattresses.
Current edition approved March 1, 2014June 1, 2022. Published March 2014June 2022. Originally approved in 2014. Last previous edition approved in 2014 as
F2755 – 14. DOI: 10.1520/F2755-14.10.1520/F2755-22.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2755 − 22
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ANSI Standards:
ANSI Z535.4ANSI Z535.4 Standard for Product Safety Signs and Labels
ANSI Z535.6ANSI Z535.6 Product Safety Information in Product Manuals, Instructions, and Other Collateral Materials
3. Safety RequirementsLabeling Requirements—Product
3.1 Soft and hard outer retail packaging or storage container, or both, of the product shall, on the principal display panel, include
all of the cautionary information in accordance with 5.2. Each mattress shall have a permanent label or sewed-on tag located in
a conspicuous location stating all of the cautionary information in accordance product shall be labeled with 5.2.warnings.
3.2 On product labels with cautionary information Warnings shall be in contrasting color(s) to the background, permanent, and
conspicuous.colors, in sans serif font, visible to the person inflating the product into its use position(s), and permanent. Permanent
is defined as the warnings remaining legible w
...